Panasonic Easa-Phone VA-824 Instrucciones de montaje

Thank you for purchasing the Panasonic Easa-Phone VA-824, Key Telephone System.

This system can connect eight central office lines and twenty four key telephones and DSS, door box, external paging amp and

external music source can be added.

Please read this manual carefully before the installation of this system.

Please follow the installation procedure described below.

Before connecting telephone lines, inform to telephone company of the following.

COLI

Telephone numbers COL2

COL3

COL4

COL5

COL6

COL7

COL8

Model number

FCC registration number for VA-824 KSU from factory

When modified to PBX (See page 18)

Factory interface code

Service order code

Ringer equivalence

Required network interface jack

Panasonic VA-824

ACK8GR-19274-KF-E

ACK8GR-19273-MF-E

02LS2

9.OF

0.4B

USOC RJI IW, RJl IC

CONTENTS

1. SYSTEMCONNECTIONLAYOUT ....................................................... 1

2. INSTALLATION OF KEY SERVICE UNIT ................................................. 3

How to wall mount the key service unit ................................................... 3

3. INSTALLATIONOFKEYTELEPHONE ................................................... 5

How to wall mount the key telephone .................................................... 5

4. WIRINGCONNECTIONS ............................................................. 6

Connection between the KSU, Key TEL and CO/PBX line ....................................... 6

Typeofwires ..................................................................... 7

Wiringcables.. ................................................................... 8

5. CONNECTION OF OPTIONAL UNIT ..................................................... 9

Variation of card connection .......................................................... 9

Extension of CO/PBX line ............................................................ 10

Connection of direct station selector ..................................................... 11

Connections of single line telephone or 2 Key TE Ls/2 SLTs ...................................... 12

Connection of door box. ............................................................. 13

Connections of sensor and door opener. ................................................... 14

Connection of SMDR ............................................................... 15

External music on hold source and external paging system ....................................... 17

Set up for key service unit ............................................................ 18

6. CONNECTION OF POWER FAILURE UNIT ..................................... ‘-. ......... 19

7. SPECIFICATIONS OF SYSTEM ......................................................... 21

Modules and system configuration ....................................................... 21

System capacity and specifications. ...................................................... 22

Checklistofparts .................................................................. 23

PROGRAMMING . . . . . . . . . . . . . , . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. INITIAL SET LIST. .................... 25

2. METHOD OF PROGRAMMING ............ 27

3. PROGRAMMING ...................... 30

System setting ........................ 30

PBX outside dialing digit ................ 30

Automatic pause ..................... 31

Call duration display appear timing ......... 32

Flash time .......................... 33

Pause time. ......................... 34

System speed dial group A ............... 35

System speed dial group B ............... 38

Long speech alarm .................... 37

COL auto answering ................... 38

COL night incoming ring mode ............ 39

Hold recall ......................... 40

Connection of door box. ................ 41

Type of applicable sensor ................ 42

Sensor alarm stopping method ............ 43

Detection of SLT on-hooking ............. 44

Connection of DSS .................... 45

Hold recall for DSS TEL ................ 48

Display time system setting .............. 47

SMDR output ....................... 48

SMDR YEAR, MONTH and DAY setting ..... 49

SMDR baud rate setting ................. 50

SMDR frame configuration. .............. 51

Type of COL dialing ................... 52

++ and #restriction .................... 53

Digit length restriction .................. 54

Incoming call restriction ................ 55

Override setting ...................... 58

COL setting .......................... 57

Tone/pulse dialing signal conversion ......... 57

COlineorPBXline.. .................. 58

Automatic outside line selection group ....... 59

Length of DTMF signals. ................ 80

Minimum pause ...................... 81

Ring detection time ................... 82

Key telephone setting ................... 83

Telephone type ...................... 83

Line Key assign ...................... 84

Incoming call ringing ................... 88

Off-hook signaling .................... 72

Door box call ........................ 73

Sensor ringing ........................ 74

Zone paging. ........................ 75

System speed dial group. ................ 78

Flexible night service setting .............. 77

Flexible night service ................... 78

Outside dialing restriction class ............ 79

System speed dial restriction .............. 83

APPENDIX: Names and phone numbers list for system

speed dialing . . . . . . . . . . . . . . . . . . . 84

Programming table for initial set . . . . . . 85

Priority for simultaneous calling and

receiving . . . . . . . . . . . . . . . . . . . . . . 141

Tones and lamp indications. . . . . . . . - - 143

189

EM CONNECTION LAYOUT

Full system configuration layout

’ EXT. No. 28 i

I l-JI

I I

I I I

1 EXT. No. 26 I

1 EXT. No. 25 I

I I

1 Door opener Al

I-- -IL--

See page 14

EXT. No. 23 I

i_---_--

See page 9 I- --,

L--l

For option

Key service unit

(KSU)

External paging f-1

1 Speaker AMP

L---

Seepage,7 -----------A

r------l

L I I

- SMDR I

L----J

See page 15

•i : Terminal box

1. SYSTEM CONNECTION LAYOUT

Power failure unit

See page 19 I

I EXT. No. 21

EXT. No. 32

eT2 ----- ----- _____

EXT. No. 20

See page 10

To central r -m

office line I1 2

I EXT. No. 17

Power and grounc

(AC 12OV)

I EXT. No. 16

EXT. No. 15

External music on hold source

r--- 3 ----

+-----)

-___---- ___-----------------_____I --_---------- -I

See page 17 See page 6

2. INSTALLATION OF KEY SERVICE UNIT

How to wall mount the key service unit

Install the key service unit (KSU) on the wall according to the following procedure.

@ Slide the two hooks securing the KSU cover and the key service unit in the arrow direction, then remove the cover.

@ Place template against wall and install the four wood screws. Use the wood screw installation jig provided inside the

key service unit when installing the wood screws.

@ Install the key service unit by hooking the four installation holes at the bottom of the key service unit to the four wood

screws, then tighten the two left side wood screws completely.

NOTE

“Be sure the power switch is OFF, before installation.”

Avoid installing in the following places. (Doing so may result in malfunction, noise, or discoloration)

a) In direct sunlight, hot, cold, or humid places. (Temperature range: 32’F - 104’F)

b) Fulfuric gases produced in areas where there are thermal springs, etc. may damage the equipment or contacts.

c) Places in which shocks or vibrations are frequent or strong.

d) Dusty places, or places where water or oil may come into contact with the unit.

e) Near high-frequency sewing machines or electric welders.

f) On or near computers, telexs, or other office equipment, as well as microwave ovens or air conditioners. (It is preferable

not to install in the same room with the above equipment)

g) Near radio broadcast antennas. (including short wave)

h) Install at least 6 feet from radiosand televisions. (both the key service unit and key telephones)

i) Do not obstruct area around the key service unit. (for reasons of maintenance and inspection - be especially careful to

allow space for cooling above and at the sides of the key service unit)

-I

2. INSTALLATION OF KEY SERVICE UNIT

Key service Unit

3. INSTALLATION OF KEY TELEPHONE

How to wall mount the key telephone

Install the key telephone on the wall according to the following procedure.

0 Pull handset guide, turn it upside

down, then insert it into its position.

@ Push the hooks at two places, then

remove the adapter.

@ Turn the adapter upside down, insert

the guides into two adapter mounting

holes provided at the lower portion of

the key telephone, then push in the

adapter.

@ Place the mounting holes of the

bracket over the studs of the modular

jack and pull the phone downward to

secure in place.

Short station cords are provided to

attach the key telephone.

NOTE

Handset cord obtainable on the market.

t MODEL NO. t LENGTH I

VAX-20884 7 feet

VAX-20885 15 feet

4. WIRING CONNECTIONS

( Connection between the KSU, Key TEL and CO/PBX line

Make connections between the KSU, Key TEL and the central office/PBX line (CO/PBX) according to the following procedure.

Connection between the KSU and

CO/PBX line

Connect COL No. 1 through No. 6

jacks provided inside the KSU to the

CO/PBX line, respectively.

0 Connection between the KSU and Key

TEL

Connect EXT No. 10 through No. 21

jacks provided inside the KSU to the

key telephones, respectively.

EXT No. 10 is desirable to use an LCD

display type key telephone (VA-12022

or VA-12022-B) that is used for the

PROGRAMMING purpose described

later. (see page 28.)

0 Clampring of cords

@ Push in the cables from the top of

the cable guide.

@ Remove the clamp plate, insert

the cords, then reinstall the clamp

plate over the cords and secure

into place with the screw.

NOTE

0 Keep the loop wire resistance to the

key telephone furthest from the key

service unit less than 40 ohms. (Max.

1100 feet with 22 AWG cable)

Do not wire the telephone cable in

parallel with the AC power source,

computer, telex etc. If the cables run

near those wires, shield the cables

within metal tubing or use shielded

cable and ground the shields.

When cables run on the floor, use pro-

tectors or the like to protect the wires

where they may be stepped on. Avoid

wiring under carpets.

0 When using an AC power supply (AC

12OV), make sure the unit is ground.

TO the central

office lines

Cl lIIrIIIllII~

\vI\

to COL

_ COL6 IL EXT. No. 21

, EXT. No. 2(

COL5 A EXT. No. l!

L EXT. No. II

COL4 iL EXT. No. 1’

COL3 L EXT. No. II

AL EXT. No. 1’

< EXT. No. l<

COL2 A EXT. No. 1:

L EXT. No. 1:

COLI h EXT. No 1

c EXT. No. I,

to key telephone

Type of wires

a CONNECTION OF WIRING CABLE (FOR USE WITH A MODULAR CONNECTOR)

(a) If the key service unit and the exten-

sion are within 25 feet, use the cable

supplied (7 feet, 15 feet or 25 feet).

(See page 21)

KSU

----_

--A---o

Quad cable

\ J

25 FEET

[Max option:

cord)

(b) Station cord and Handset cord

Depending on the connection and

length, 4 types of station cords and 2

types of Handset cords are available.

(See page 21)

extension are apart by more than 200

feet, please use quad cable. Quad

cables assure proper operation over

long distance than flat cables.

In this case, use connector

(Modu-

lar-Screw).

0 Terminal Box

When coupling cables, either of the

following can be used (m or

Key-TEL

200 FEET

(Max flat

cable)

Flat cable

Flat cable obtainable on the market.

Optional cord

MODEL NO. LENGTH

VAX-20880 Short station cord

(wall-mount only)

VAX-20881 7 feet

VAX-20882 15 feet

VAX-20883 25 feet

--------- ----__ -----

Up to 1100 FEET

MODULAR (Max quad cable)

CONNECTOR - MODULAR

CONNECTOR TERMINAL BOX

cl B MODULAR

CONNECTOR - SCREW TERMINAL BOX

Quad cables explanation

Selecting quad cable depends upon the

wiring length.

Make sure that the quad cables are

twisted pair or shielded twisted pair. r

Ti TYPE

Brminal (VAX-208861

Box Terminal Modular M Modular Modular M Screw

NOTE Use the four conductor type

inline coupler. Use this type when the quad cable

and door box unit is connected.

Flat cable Flat cable Flat cable Quad cable

Note: Quad cables are not used for attach-

ing modular terminals. COUPLING

OF CABLE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema telefónico de Panasonic

Panasonic

Panasonic KX-TD308 Manual de usuario

Panasonic

Panasonic KX-TA30820B Manual de usuario

Panasonic

Panasonic KX-TD1232E Manual de usuario

Panasonic

Panasonic KX-TSC11 Manual de usuario

Panasonic

Panasonic KX-TA1232 Instrucciones de instalación y funcionamiento

Panasonic

Panasonic KX-TA1232 Manual de usuario

Panasonic

Panasonic KX-TD816 Manual de usuario

Panasonic

Panasonic KX-TD816E Manual de usuario

Panasonic

Panasonic KX-TS2388RUB Manual de usuario

Panasonic

Panasonic KX-TVS90 Manual de usuario

Panasonic

Panasonic KX-TD6112E Hoja de especificaciones

Panasonic

Panasonic KX-TE82461X Manual de usuario

Panasonic

Panasonic Easa-Phone VA-30910 Manual de usuario

Panasonic

Panasonic KX-TG5110M - 5.8 GHz DSS Expandable Cordless... Manual de usuario

Panasonic

Panasonic KX-NS700 Manual del propietario

Panasonic

Panasonic KX-TA624 Especificaciones técnicas

Panasonic

Panasonic VB-44210G Manual de usuario

Panasonic

Panasonic KX-TDA100D Manual de usuario

Panasonic

Panasonic KX-TD208 Manual de usuario

Panasonic

Panasonic KX-TDA50 Manual de usuario

Panasonic

Panasonic KX-TSC11AGW Manual de usuario

Panasonic

Panasonic KXFG2451 - B/W Thermal Transfer Manual de usuario

Panasonic

Panasonic KX-TCD445BXS Manual de usuario

Panasonic

Panasonic KX-TD500CE Manual de usuario

Manuales populares de Sistema telefónico de otras marcas

Teleco

Teleco Perfect Voice Tis 16 Manual de usuario

AT&T

AT&T Network Adapter 25 Manual de usuario

AVE

AVE AF902R-CE Manual de usuario

Tynetec

Tynetec Advent xt Manual de usuario

Ericsson

Ericsson DCT1800-S Manual de usuario

NEC

NEC Electra Elite 192 Manual de usuario

Alcatel

Alcatel EASY REFLEXES 4200 Manual de usuario

Bticino

Bticino PABX 28D Manual de usuario

NEC

NEC SL 2100 Manual de usuario

Sonifex

Sonifex Phone In 6 Manual de instrucciones

TransTel Communications

TransTel Communications TD-824i Instrucciones de montaje

Nortel

Nortel BCM50 Manual del producto

ASCOM

ASCOM TD 92375GB Manual del propietario

Karel

Karel MS26S Hoja de información del producto

EnGenius

EnGenius DuraFon PRO Manual de usuario

Teledat

Teledat X130 DSL Manual de usuario

SpectraLink

SpectraLink MOG400 Manual de usuario

LG-Nortel

LG-Nortel 300 Series Instrucciones de funcionamiento y seguridad