Panasonic MINAS A6 Series Manual de usuario
Servo Drives
Quick Start Guide
MINAS A6 Multi
PANATERM
Ethernet over EtherCAT (EoE)
QS10001_V1.0_EN
2020.11 https://industry.panasonic.eu
Liability and copyright
Liability and copyright
This manual and everything described in it are copyrighted. You may not copy this manual, in
whole or part, without written consent of Panasonic Electric Works Europe AG (PEWEU).
PEWEU pursues a policy of continuous improvement of the design and performance of its
products. Therefore we reserve the right to change the manual/product without notice. In no
event will PEWEU be liable for direct, special, incidental, or consequential damage resulting
from any defect in the product or its documentation, even if advised of the possibility of such
damages.
Please direct support matters and technical questions to your local Panasonic
representative.
Panasonic Electric Works Europe AG (PEWEU)
Caroline-Herschel-Strasse 100
85521 Ottobrunn, Germany
Tel: +49 89 45 354-1000
2 QS10001_V1.0_EN
Table of contents
Table of contents
1 Introduction................................................................................................................................. 4
1.1 Before you start................................................................................................................................ 4
1.2 About this document.........................................................................................................................4
1.3 Related documents........................................................................................................................... 4
1.4 Available software............................................................................................................................. 5
2 Functional overview................................................................................................................... 6
3 Wiring...........................................................................................................................................8
3.1 Basic wiring of the MINAS A6 Multi................................................................................................. 8
3.2 Connect the EtherCAT communication cable...................................................................................8
4 Set up the host controller......................................................................................................... 9
4.1 Set the IP address in your PC......................................................................................................... 9
4.2 Check the EtherCAT driver installation.............................................................................................9
4.3 Add connected devices to your project............................................................................................ 9
4.4 Activate the EoE functionality in your TwinCAT project..................................................................11
5 Connect PANATERM via EoE..................................................................................................13
6 Activate the TwinCAT Runtime software license.................................................................. 14
7 Help us improve....................................................................................................................... 15
8 Record of changes................................................................................................................... 16
9 Panasonic hotline.....................................................................................................................17
QS10001_V1.0_EN 3
1 Introduction
1 Introduction
1.1 Before you start
Before operating this product, read the safety instructions in the following manuals:
•“SX-DSV03514, MINAS A6 Multi, Technical Reference – Integrated Safety Part”
•“SX-DSV03508, MINAS A6 Multi, Programming Manual – PANATERM for Safety”
This product is for industrial use only.
Electrical connections must be made by qualified electrical personnel.
1.2 About this document
This “Quick Start Guide” is intended to help you set up a MINAS A6 Multi servo drive
system. It is based on information from the MINAS A6 Multi series manuals and the practical
experience of our engineers.
A PC can be used as a host controller to perform Ethernet communication via EtherCAT
(EoE) with a MINAS A6 Multi servo drive system. Step by step instructions will guide you
through installing Beckhoff’s TwinCAT 3 software to configure the EtherCAT functionality on
your PC. And you will learn how to connect the PC configuration software PANATERM with
the MINAS A6 Multi servo drive system via EtherCAT.
In these instructions we assume that you are using a Windows 10 operating system.
Please refer to the original documentation of our servo drive systems for detailed
information. It is available free of charge in our Panasonic Download Center.
1.3 Related documents
Select the following links to download the documents from our Panasonic Download Center.
• Safety specifications:
“SX-DSV03514, MINAS A6 Multi, Technical Reference – Integrated Safety Part”
• Information on wiring the MINAS A6 Multi servo drive system:
“SX-DSV03454, MINAS A6 Multi, Reference Specifications – Driver Module”
• Information on wiring the MINAS A6 Multi power supply module:
“SX-DSV03452, MINAS A6 Multi, Reference Specifications – Power Supply Module”
• Information on EtherCAT communication:
4 QS10001_V1.0_EN
1 Introduction
“SX-DSV03456, MINAS A6 Multi, Technical Reference – EtherCAT Communication
Specification”
• Description of the servo driver functions:
“SX-DSV03455, MINAS A6 Multi, Technical Reference – Functional Specification”
• Information on safety programming:
“SX-DSV03508, MINAS A6 Multi, Programming Manual – PANATERM for Safety”
• Information on how to reduce electromagnetic interference (EMI):
“Recommendations for EMC-compliant wiring of servo drivers and motors”
• Related Quick Start Guides:
“QS10000, MINAS A6 Multi, Position control with Beckhoff host controller over EtherCAT”
“QS10002, MINAS A6 Multi, Safe Torque Off (STO)”
“QS10003, MINAS A6 Multi, Safe Stop 1 (SS1)”
“QS10004, MINAS A6 Multi, Safe Speed Monitoring (SSM)”
“QS10005, MINAS A6 Multi, Position control with Omron host controller over EtherCAT”
“QS10006, MINAS A6 Multi, Position control with TRIO host controller over EtherCAT”
1.4 Available software
The following software is available free of charge in our Panasonic Download Center:
• PC configuration software PANATERM for MINAS A6 Multi, 32 bit, or PC configuration
software PANATERM for MINAS A6 Multi, 64 bit
• Panasonic ESI file
The following software can be downloaded from Beckhoff’s Web site (https://
www.beckhoff.de):
• TwinCAT3 Engineering software (Go to “Download” > “Software” > “TwinCAT3” >
“Engineering”)
QS10001_V1.0_EN 5
2 Functional overview
2 Functional overview
A Panasonic MINAS A6 Multi servo drive system includes a power supply module, one
or more 400V driver modules, and one or two motors connected to each driver module.
Communication can be achieved through EtherCAT with any host controller that supports the
CAN application protocol over EtherCAT (CoE).
With Beckhoff’s TwinCAT 3 software, a PC can be configured as an EtherCAT host controller.
The PC configuration software PANATERM is used to perform the communication with the
MINAS A6 Multi servo drive system.
Example
A servo drive system, consisting of a 15kW power supply module, an A-size 1.5kW two-axis
driver module, and two servo motors with a rated power of 1.0kW and 1.5kW, is connected
to a PC by an Ethernet cable to communicate via EoE.
Use the following accessories:
• 1 x 400V AC power supply cable
Connects the MINAS A6 Multi power supply module to the main power supply (400V AC).
• 1 x 24V DC power supply cable
Connects the power supply unit (24V DC) and the host controller.
• 1 x grounding wire (M4 round terminal)
Connects the PE terminals of the power supply module and the driver module.
• 2 x Panasonic motor cable
Connects the motor and the driver module.
• 2 x Panasonic encoder cable
Connects the encoder and the driver module.
• 1 x Ethernet cable (RJ45)
Connects the PC and the driver module.
• 1 x RJ11 communication cable (2 x RJ11 plug)
Connects the power supply module and the driver module.
• 1 x feed bus bar (50mm) with end cap for the DC link bus (535V DC to 675V DC)
Connects the power supply module and the driver module.
• 1 x feed bus bar (50mm) with end cap for the control bus (24V DC)
Connects the power supply module and the driver module.
6 QS10001_V1.0_EN
2 Functional overview
(1) (2) (3) (4) (5)
(6)
(1) Power supply unit (24V DC)
(2) MINAS A6 Multi power supply module (400V AC, 15kW)
(3) Two-axis MINAS A6 Multi driver module (1.5kW)
(4) MINAS A6 servo motor B (1.5kW)
(5) MINAS A6 servo motor A (1kW)
(6) PC with TwinCAT 3 Engineering software and PANATERM
Set-up of a MINAS A6 Multi servo drive system - Ethernet over EtherCAT with PANATERM
QS10001_V1.0_EN 7
3 Wiring
3 Wiring
3.1 Basic wiring of the MINAS A6 Multi
Check the hardware connections of your servo drive system:
• 24V DC control power supply connected to X11
• 400V AC main power supply cable connected to X102
• Motor cable for servo motor A connected to X105A
• Motor cable for servo motor B connected to X105B
• Encoder cable for servo motor A connected to X9A
• Encoder cable for servo motor B connected to X9B
• X1 and X1A connected with RJ11 communication cable
• Bus bars attached to X104 and X12
• PE terminals of power supply module and driver module connected by grounding wire
For details on how to do the wiring of the MINAS A6 Multi servo drive system, refer to
“Wiring” in “QS10000, MINAS A6 Multi, Position control with Beckhoff host controller over
EtherCAT”.
3.2 Connect the EtherCAT communication cable
Connect an Ethernet cable between the PC and the EtherCAT connector (X6A) of the driver
module. The connector is located on the top side of the driver module.
(1)
(1) X6A: EtherCAT connector on driver module
8 QS10001_V1.0_EN
4 Set up the host controller
4 Set up the host controller
4.1 Set the IP address in your PC
1. In Windows, go to “Network Connections” > “Change adapter options”.
2. Select “Ethernet” > “Properties”.
3. On the “Network” tab, select “Internet protocol, Version 4 (TCP/IPv4)” > “Properties”.
4. Select “Use the following IP address” and set the IP address.
Example:
IP address: 192.168.0.100
Subnet mask: 255.255.255.0
4.2 Check the EtherCAT driver installation
The EtherCAT driver is installed with TwinCAT 3. Check whether the Ethernet interface of the
PC is correctly configured as an EtherCAT interface.
1. Select “TwinCAT” > “Show Real Time Ethernet Compatible Devices” in the TwinCAT 3
toolbar.
2. Make sure the Ethernet network adapter is displayed under “Installed and ready to use
devices (realtime capable)”.
4.3 Add connected devices to your project
You must add the connected devices to your TwinCAT project.
QS10001_V1.0_EN 9
4 Set up the host controller
1. In the “Solution Explorer”, go to “I/O” and right-click on “Devices”. Select “Scan”.
2. Confirm the message that not all devices can be found automatically.
3. When the EtherCAT master device is found, select “OK”.
4. Confirm “Scan for boxes” with “Yes”.
5. When the MINAS A6 Multi driver module is found, the following message comes up that
you confirm with “OK”.
6. Confirm the message “Activate Free Run” with “No”.
10 QS10001_V1.0_EN
Otros manuales para MINAS A6 Series
9
Tabla de contenidos
Otros manuales de Servoaccionamiento de Panasonic
Panasonic
Panasonic MINAS-A4N Manual de usuario
Panasonic
Panasonic MINAS A5E Series Manual de usuario
Panasonic
Panasonic MHMD042P1C Manual de uso y cuidado
Panasonic
Panasonic MINAS A6N Series Manual de usuario
Panasonic
Panasonic LIQI Manual de usuario
Panasonic
Panasonic MINAS A6 Series Manual de usuario
Panasonic
Panasonic MINAS-A5B Series Manual de uso y cuidado
Panasonic
Panasonic MINAS A6 Series Manual de usuario
Panasonic
Panasonic MINAS-A6 Series Manual de usuario
Panasonic
Panasonic MADDT1207 Manual de uso y cuidado
Panasonic
Panasonic MINAS A5 Series Manual de usuario
Panasonic
Panasonic MINAS A6 Series Manual de usuario
Panasonic
Panasonic MSDA043A1A Manual de usuario
Panasonic
Panasonic MINAS-A5BL Series Manual de usuario
Panasonic
Panasonic A5N9 Series Manual de usuario
Panasonic
Panasonic MINAS-A6B Series Manual de usuario
Panasonic
Panasonic PANATERM QS5000 Manual de usuario
Panasonic
Panasonic MINAS A6 Series Manual de uso y cuidado
Panasonic
Panasonic MINAS-A5NL Series Manual de uso y cuidado
Panasonic
Panasonic FP0H Series Manual de usuario
Manuales populares de Servoaccionamiento de otras marcas
Mitsubishi Electric
Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manual de usuario
Robotis
Robotis XH430-W350-T Manual de usuario
NTI AG
NTI AG LinMot C1250 Series Manual de usuario
Welcon
Welcon WE2A D048 Series Manual de usuario
Parallax
Parallax 900-00005 Manual de usuario
Festo
Festo TP 1410 Manual de usuario
