Panasonic WVCS854 - COMBINATION CAMERA Manual de instrucciones

Installing PTZ Cameras

on a DVX system

Panasonic WV-CS854 Dome

External RS-485 Control

June 2002

#3000-40046 Rev. 2

Installing PTZ Cameras on a DVX system

June 2002

Page

Installing Panasonic WV-CS854 on a DVX system

To use a Panasonic WV-CS854 camera with a DVX system , you must wire the camera to the RS-485 converter, and then

plug the converter into the COM port on the DVX system. The A pin must be connected to the orange T and yellow R wires

from the camera, and the COM B pin must be connected to the red T and green R wires from the camera:

RS-485 converter pin Panasonic 5-wire terminal

COM A Orange T (A)

COM B Red T (B)

COM A Green R (A)

COM B Yellow R (B)

The following figure illustrates the connection points between the DVX system and the camera. (Drawing not to scale; DVX

drawing may not match your particular DVX model.)

SW1 SW2

OFF

DVX System

External RS-485 converter

7 to 12 VAC/DC

power adapter

PWR

COM A

COM B

Red T (B)

Yellow R (B)

Orange T (A)

Green R (A)

Panasonic WV-CS854

On the Setup page in

MasterControl, make sure

you select COM1 on the PTZ

tab for this camera.

Installing PTZ Cameras on a DVX system

June 2002

Page

Panasonic WV-CS854: Setup Instructions

The figure on the previous page shows the SW1 switch used to select the protocol, communication parameter, and camera

address. You must set this switch three times, as described in the following instructions:

1. Select the protocol by setting SW1 as follows (factory default settings):

12345678

OFF ON OFF ON ON OFF OFF OFF

2. Insert the camera in its mount and wait for the camera to complete the startup sequence.

3. Remove the camera from its mount.

4. Select the communication parameters (9600bps, data bit 8, parity check N, stop bit 1) by setting SW1 as follows:

12345678

OFFONONONONOFFOFFOFF

5. Insert the camera in its mount and wait for the camera to complete the startup sequence.

6. Remove the camera from its mount.

7. Select a unique camera address from 1 to 32 by setting SW1 as follows (note that 8 is ON in each case):

Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

1 ON OFF OFF OFF OFF OFF OFF ON

2 OFF ON OFF OFF OFF OFF OFF ON

3 ON ON OFF OFF OFF OFF OFF ON

4 OFF OFF ON OFF OFF OFF OFF ON

5 ON OFF ON OFF OFF OFF OFF ON

6 OFF ON ON OFF OFF OFF OFF ON

7 ONONONOFFOFFOFFOFFON

8 OFF OFF OFF ON OFF OFF OFF ON

9 ON OFF OFF ON OFF OFF OFF ON

10 OFF ON OFF ON OFF OFF OFF ON

11 ON ON OFF ON OFF OFF OFF ON

12 OFF OFF ON ON OFF OFF OFF ON

13 ON OFF ON ON OFF OFF OFF ON

14 OFFONONONOFFOFFOFFON

15 ON ON ON ON OFF OFF OFF ON

16 OFF OFF OFF OFF ON OFF OFF ON

17 ON OFF OFF OFF ON OFF OFF ON

18 OFF ON OFF OFF ON OFF OFF ON

19 ON ON OFF OFF ON OFF OFF ON

20 OFF OFF ON OFF ON OFF OFF ON

21 ON OFF ON OFF ON OFF OFF ON

22 OFF ON ON OFF ON OFF OFF ON

23 ON ON ON OFF ON OFF OFF ON

24 OFF OFF OFF ON ON OFF OFF ON

25 ON OFF OFF ON ON OFF OFF ON

26 OFF ON OFF ON ON OFF OFF ON

27 ON ON OFF ON ON OFF OFF ON

28 OFF OFF ON ON ON OFF OFF ON

29 ONOFFONONONOFFOFFON

30 OFFONONONONOFFOFFON

31 ON ON ON ON ON OFF OFF ON

32 OFF OFF OFF OFF OFF ON OFF ON

8. Insert the camera in its mount and wait for the camera to complete the startup sequence.

Installing PTZ Cameras on a DVX system

June 2002

Page

1234

OFFONONON

1234

ON ON ON ON

Panasonic WV-CS854: Camera Termination

The figure on page 2 shows the location of the SW2 switch, which is used to select the termination (switch 1) and duplex

setting (switches 2–4, half duplex). Complete the following instructions:

1. Remove the camera from its mount.

2. Set SW2 as follows if the camera is not the final camera in a chain:

3. Set SW2 as follows if the camera is the final camera in a chain:

See the Panasonic WV-CS854 installation manual for more information.

Panasonic WV-CS854: Connecting Multiple Cameras

Additional cameras are connected to the DVX system in a daisy chain, star, or combination configuration; the final camera in

each chain must be terminated. Each camera must have a unique address that matches the video input number it is connected

to on the DVX system (see the DVX user manual). Sample configurations are shown in the following figure.

See the camera manufacturer’s installation manual for more information.

DVX

Address: 1 Address: 2 Address: 3 (terminate)

DAISY CHAIN

DVX

Address: 1

Address: 2

Address: 3

(terminate)

STAR

DVX

Address: 1

Address: 3

Address: 5

Address: 2 (terminate)

Address: 4 (terminate)

Address: 6 (terminate)

COMBINATION

Installing PTZ Cameras on a DVX system

June 2002

Page

Enabling COM Ports (Upgrade Situtations Only)

When upgrading an existing DVX system to enable PTZ capability, you must enable the COM ports on the DVX system. To

verify that the COM ports are enabled on your system, view the PTZ tab on the Setup page in MasterControl on the DVX

system. If the COM ports are not enabled, the following message is displayed on the PTZ tab:

Unable to detect COM ports on your system. You must install a COM port

to use PTZ cameras.

If this message appears, you must enable the COM (serial) ports in the system BIOS. For assistance, please contact the

Technical Support Center at 1-720-872-9100.

NOTE: The PTZ tab is available in MasterControl only if you have entered a valid PTZ license key. See the front page of

this document for details.

Otros manuales de Cámara de seguridad de Panasonic

Panasonic

Panasonic WV-X8570N Manual de funcionamiento

Panasonic

Panasonic WVCF254 - COLOR CAMERA Manual de usuario

Panasonic

Panasonic AW-UE100WP Manual de usuario

Panasonic

Panasonic WV-SF138 Manual de instalación y operación

Panasonic

Panasonic BL-VP104W Manual de usuario

Panasonic

Panasonic WV-SW352 Manual de usuario

Panasonic

Panasonic aw-he40 series Manual de usuario

Panasonic

Panasonic AJSDC915 - DVC PRO CAMCORDER Manual de usuario

Panasonic

Panasonic WVCP120 - COLOR CCTV CAMERA Manual de usuario

Panasonic

Panasonic Super Dynamic III WV-CW484S Manual de usuario

Panasonic

Panasonic VIDEOLARM PCF3 Hoja de instrucciones

Panasonic

Panasonic WV-SPN531 Manual de usuario

Panasonic

Panasonic WV-NF302E Manual de usuario

Panasonic

Panasonic WV-U2142L Guía de instalación

Panasonic

Panasonic WV-CW384E Manual de usuario

Panasonic

Panasonic KX-HNC600AZ Manual de usuario

Panasonic

Panasonic KX-HCM280 Manual de usuario

Panasonic

Panasonic WV-CW860 Manual de usuario

Panasonic

Panasonic BL-C10A - Network Camera - Pan Manual de usuario

Panasonic

Panasonic WV-CP290 series Manual de usuario

Panasonic

Panasonic WV-SC588A Manual de usuario

Panasonic

Panasonic WV-CZ352 Manual de usuario

Panasonic

Panasonic KX-HCM280A Hoja de especificaciones

Panasonic

Panasonic BL-C210 Series Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario