Panasonic OneHome BB-HCM331A Manual de usuario

Operating Instructions

Please read this manual before using and save this manual for future reference.

Panasonic Network Camera Website: http://www.panasonic.com/netcam

for customers in the USA or Puerto Rico

Model No.

BB-HCM331A

Network Camera Outdoor Ready

Operating Instructions

Main Features

Splash Resistant body for indoor and outdoor use

Your Panasonic Network Camera has a splash resistant body. The splash resistant

body allows the camera to be used indoors or outdoors.

IPv6*1 Network Camera

Your Panasonic Network Camera supports IPv6 (Internet Protocol Version 6), IPv6

was created to address the additional IP addresses that will be needed as the

Internet continues to expand. Since the camera also supports IPv4 that's currently

used, it is "dual stack" design will seamlessly operate while IPv6 is phased in. For

more information in IPv6 you wish to visit http://www.ipv6.org/. See page 14 for

more information.

Audio 2-way Communication*2 (Walkie-talkie Type)

Your Panasonic Network Camera now provides 2-way audio, between the camera

and your PC. You will be able to hear the person on camera and respond using a

microphone connected to your PC's sound card (customer-provided.) They will

hear your response through the amplified speaker (customer-provided) connected

to the camera. The audio feature uses a JavaTM applet that is installed during the

installation procedure.

For example, the camera can be used in the following various locations:

• In the baby's room, to hear if the baby is crying.

• At the front door, to see and hear who is at the door.

• In the children's play room, to see and hear if they are safe.

Note

PLEASE NOTE that under certain circumstances, audio/video recording may

be PROHIBITED by law. This device should be used only in compliance with

all applicable federal, state and local statutes.

Better Image Quality

The CCD sensor and the color night view mode provides better image quality and

low light performance.

• The CCD sensor gives you clear image.

• You can monitor live video (Motion JPEG) that refreshes its image 30 frames

per second.

*1 To connect in IPv6, subscribe to the ISP's "IPv4/IPv6 Dual-Stack" or "IPv6 over IPv4

Tunneling" service. The camera does not work in IPv6-only network.

*2 Audio feature does not work on mobile phones. Talk button and Listen button cannot be used

simultaneously. It will be supported by the firmware update in the future. In consequence of

traffic and network environments, the audio may be delayed or may break up.

Operating Instructions

3[For assistance, please call: 1-800-272-7033]

• Color night view mode allows you to monitor the camera in low illuminance.

Various Camera Control Features

The camera pans or tilts fast in maximum 80 ° per second. (The previous model:

21 ° per second) You can control the camera at high speed from your PC or mobile

phone. Alarm position feature also allows the camera to automatically turn the lens

to the alarm position. Additionally, the following control features are available to

easily and quickly monitor the camera.

SD Memory Card*1 Recording

The camera has an SD memory card slot. You can record camera images to the

SD memory card. If you enable alarm buffer/transfer, you can record the image at

the timing of signal detection of door sensor or light. About 58,000 images (320 x

240 resolution and standard quality) can be recorded to 1 GB SD memory card. If

you enable 1-minute interval timer buffer/transfer, you can record the images for

about 41 days.

Enhanced Multi-Camera Page

Multi-Camera page displays up to 4 cameras while supporting each audio 2-way

communication. The previous model displays only 4 cameras, but this camera can

switch 3 sets of 4 cameras. Additionally, the camera can displays maximum 12

cameras on a page in a static image.

Supporting Viewnetcam.com service

Viewnetcam.com service allows you to access the camera over the Internet with

your favorite domain name (e.g. bob.viewnetcam.com) instead of a global IP

address.

Multi-Language Display

Top page, Single Camera and Multi-Camera page can be displayed in English,

French, German, Italian, Spanish, Russian, Simplified Chinese or Japanese. The

Setup, Maintenance and Support pages are displayed only in English or Japanese.

Click to Center ......... When you click a certain point on the camera image, the

point is centered on the image.

Preset Position ......... You can register 8 preset positions. When you click each

button, the image switches to its position.

Output Control ......... You can control the external devices (Open or Short to

GND) (E.g., turning the light on or ringing a buzzer).

*1 SD memory card is sold separately. The camera supports 1 GB, 512 MB, 256 MB, 128 MB or

64 MB Panasonic SD memory card.

Operating Instructions

How to Use This Documentation

The camera includes the following 2 manual types.

•Installation/Troubleshooting

Installation/Troubleshooting provides explanations for accessories included

with the camera, the initial configuration, and troubleshooting tips. The

Installation/Troubleshooting helps you to easily configure the camera.

•Operating Instructions (This manual)

Operating Instructions explains about operations, settings, features and the

cleaning method when using the camera.

Abbreviations

• UPnP is the abbreviation for Universal Plug and Play.

• "Network Camera" is called "Camera" in this Operating Instructions.

Trademarks

• Adobe, Acrobat and Reader are either registered trademarks or trademarks of

Adobe Systems Incorporated in the United States and/or other countries.

• Ethernet is either a registered trademark or a trademark of Xerox Corporation

in the United States and/or other countries.

• Microsoft, Windows, Hotmail and ActiveX are either registered trademarks or

trademarks of Microsoft Corporation in the United States and/or other

countries.

• Pentium is a trademark or registered trademark of Intel Corporation or its

subsidiaries in the United States and other countries.

• SD mark is a trademark of the SD Card Association.

• Screen shots reprinted with permission from Microsoft Corporation.

• All other trademarks identified herein are the property of their respective

owners.

Operating Instructions

5[For assistance, please call: 1-800-272-7033]

System Requirements for your PC

Your PC (Personal Computer) and network must meet the following technical

specifications for the camera to work properly.

For IPv4 Connection

Item Description

Operating

System

Microsoft®Windows®XP, Microsoft®Windows®2000

Microsoft®Windows®Me, Microsoft®Windows®98SE

CPU •For viewing single camera

Pentium®III (800 MHz or greater is recommended.)

•For viewing multiple cameras

Pentium 4 (1.8 GHz or greater is recommended.)

Protocol TCP/IP protocol (HTTP, TCP, UDP, IP, DNS, ARP, ICMP)

Interface 10/100 Mbps network card installed

Web Browser Internet Explorer 6.0 or later (Not included on the Setup CD-

ROM)

Audio Audio input/output feature (Microphone or speaker)

Operating Instructions

Note

See Panasonic Network Camera support website at

http://panasonic.co.jp/pcc/products/en/netwkcam/ for the latest

information about web browser.

For IPv6 Connection

Item Description

Operating

System

Microsoft®Windows®XP Service Pack 1

CPU •For viewing single camera

Pentium III (800 MHz or greater is recommended.)

•For viewing multiple cameras

Pentium 4 (1.8 GHz or greater is recommended.)

Protocol TCP/IP protocol (HTTP, TCP, UDP, IP, DNS, ICMPv6, NDP)

Interface 10/100 Mbps network card installed

Web Browser Internet Explorer 6.0 or later (Not included on the Setup CD-

ROM)

Audio Audio input/output feature (Microphone or speaker)

Operating Instructions

7[For assistance, please call: 1-800-272-7033]

IMPORTANT SAFETY INSTRUCTIONS

When using this unit, basic safety precautions should always be followed to reduce

the risk of fire, electric shock, or personal injury.

1. Read and understand all instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. After taking away the sand or the dust on the lens cover, wipe the lens cover

with a dry cloth.

6. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves,

or other devices (including amplifiers) that produce heat.

8. Protect the AC adaptor cord and AC cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where they exit

from the unit.

9. The AC cord is used as the main disconnect device, ensure that the socket-

outlet is located/installed near the equipment and is easily accessible.

10. Only use attachments/accessories such as stand specified by the

manufacturer.

11. Do not touch the unit or the AC adaptor cord and AC cord during lightning

storms.

12. Unplug the unit when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when

the unit has been damaged in any way, such as the AC adaptor cord, AC cord

or plug is damaged, the unit does not operate normally, or has been dropped.

14. The attached AC adaptor and AC cord is intended for indoor use only. Both AC

adaptor and AC cord must be waterproofed for outside use.

15. Keep the SD memory card (customer-provided) out of reach of children to

prevent swallowing.

SAVE THESE INSTRUCTIONS

Operating Instructions

User Name and Password Protection

The use of a unique User Name and secret Password is an important tool that

will help limit unauthorized individuals from accessing the camera. If you

choose to disable this tool, and choose not to limit access by use of a User

Name and Password, this may result in access to the camera by

unauthorized individuals. (see page 70)

Operating Instructions

9[For assistance, please call: 1-800-272-7033]

Table of Contents

1 Camera Monitoring......................................................12

1.1 Accessing the Camera................................................................. 12

1.1.1 To Access the Camera in IPv6 ................................................................ 14

1.2 Viewing Single Camera page....................................................... 16

1.2.1 Auto Centering the Image (Click to Center)............................................. 19

1.2.2 Capturing a Still Image ............................................................................ 20

1.2.3 Using Operation Bar ................................................................................ 21

1.2.4 Setting Home Position/Alarm Position/Preset Button .............................. 23

1.3 Listening to Camera Audio—Talking to the Camera .................... 27

1.4 Viewing Multi-Camera page ......................................................... 30

1.5 Viewing Buffered Image page ...................................................... 32

1.5.1 Deleting Buffered Images ........................................................................ 34

1.6 Viewing Still Images on Your Mobile Phone................................. 35

2 Various Camera Features ...........................................37

2.1 Using Camera Features ............................................................... 37

2.2 Connecting the Camera to Your IPv4 Network............................. 40

2.3 Connecting the Camera to Your IPv6 Network............................. 44

2.4 What is IPsec? ............................................................................. 48

2.5 Encrypt the Camera Image in Transport Mode ............................ 51

2.6 Encrypt the Camera Image in Tunnel Mode................................. 54

2.7 Using UPnP™ (Universal Plug and Play) .................................... 58

2.8 Registering with the Viewnetcam.com service............................. 60

2.9 Setting Date and Time ................................................................. 62

2.10 Changing Camera Settings.......................................................... 64

2.11 Adjusting Audio ............................................................................ 68

2.12 Changing Authentication Setting and Administrator User Name and

Password...................................................................................... 70

2.13 Logging in to the Camera............................................................. 73

2.14 Creating, Modifying or Deleting General Users............................ 74

2.15 Changing Initial Settings on the Single Camera page or the Multi-

Camera page ............................................................................... 76

Operating Instructions

2.16 Configuring Multiple Cameras...................................................... 79

2.17 Format the SD memory card ....................................................... 81

2.18 Stop the SD Memory Recording .................................................. 82

2.19 Buffering or Transferring Images by Timer................................... 83

2.20 Buffering or Transferring Images by Alarm Signal........................ 92

2.21 Transfer the Camera Image in Transport Mode.......................... 103

2.22 Transfer the Camera Image in Tunnel Mode .............................. 104

2.23 Specifying Operation Time......................................................... 105

2.24 Controlling External Output Terminal ......................................... 107

2.25 Changing Indicator Display ........................................................ 108

3 Camera Maintenance ................................................109

3.1 Maintenance page ..................................................................... 109

3.1.1 Confirming the Status ............................................................................ 110

3.1.2 Restarting the Camera .......................................................................... 110

3.1.3 Updating the Camera Firmware............................................................. 111

3.1.4 Creating Configuration File .................................................................... 114

3.1.5 Loading Settings from a Configuration File............................................ 115

3.1.6 Resetting the Camera to Factory Default............................................... 116

3.2 Support page ............................................................................. 117

3.2.1 Seeing Help page .................................................................................. 117

3.2.2 Seeing Product Information ................................................................... 117

3.2.3 Seeing Support Information................................................................... 118

3.3 External I/O................................................................................ 119

3.4 FACTORY DEFAULT RESET Button.......................................... 121

3.5 RESTART Button ....................................................................... 122

3.6 Default Setting List..................................................................... 123

3.7 Cleaning..................................................................................... 131

3.7.1 Cleaning the Main Unit .......................................................................... 131

3.8 Setting an IP Address on Your PC ............................................. 132

3.9 Using Setup Program................................................................. 133

3.10 Setting Your PC.......................................................................... 136

3.10.1 Setting the Proxy Server Settings on Web Browser ............................. 136

3.10.2 Setting UPnP™ to Display Camera Shortcut in My Network Places..... 139

3.10.3 Setting the Internet Temporary File Setting on Web Browser................ 139

3.11 ASCII Character Table ............................................................... 140

Otros manuales para OneHome BB-HCM331A

Tabla de contenidos

Otros manuales de Cámara de seguridad de Panasonic

Panasonic

Panasonic AW-HE60 Manual de usuario

Panasonic

Panasonic Super Dynamic III WV-CW964 Manual de usuario

Panasonic

Panasonic WVPS15 - CAMERA DRIVE UNIT Manual de usuario

Panasonic

Panasonic WV-CF334E Manual de usuario

Panasonic

Panasonic WV-S2550L Manual de funcionamiento

Panasonic

Panasonic BL-C131 Manual de usuario

Panasonic

Panasonic BB-HCM311 Manual de usuario

Panasonic

Panasonic KX-HCM280 Manual de usuario

Panasonic

Panasonic WVNM100 - NETWORK COLOR CAMERA Manual de usuario

Panasonic

Panasonic BL-WV10A Manual de usuario

Panasonic

Panasonic WV-CW590G Manual de usuario

Panasonic

Panasonic WV-SPW311AL Manual de usuario

Panasonic

Panasonic BB-HCM511 Manual de usuario

Panasonic

Panasonic WV-CS570 Manual de usuario

Panasonic

Panasonic WV-SF135 Manual de usuario

Panasonic

Panasonic PI-DNA3PWA Manual de usuario

Panasonic

Panasonic TY-CC10W Manual de usuario

Panasonic

Panasonic HomeHawk Manual de usuario

Panasonic

Panasonic i-Pro WV-SP302 Manual de usuario

Panasonic

Panasonic WV-S15700-V2L Series Manual de usuario

Panasonic

Panasonic VL-CM851BX Manual de usuario

Panasonic

Panasonic WV-S3511L Manual de funcionamiento

Panasonic

Panasonic WV-CW590A Manual de usuario

Panasonic

Panasonic WVCS854 - COMBINATION CAMERA Manual de instrucciones

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario