Panasonic KX-A272 Manual de usuario

Model KX-A272

Operating Instructions

DECT Repeater

Please read before use and save.

QUQX00130YA_01_A 20/1/04 6:40 pm Page 1

2|Operating Instructions

Table of Contents

Overview ..........................................................................................................3

Compatibility......................................................................................................3

General Safety ..................................................................................................3

Environment ......................................................................................................4

Accessories ......................................................................................................4

Wall Mounting ..................................................................................................5

Connection ........................................................................................................5

Placement ........................................................................................................6

LED Status ........................................................................................................6

Automatic Registration......................................................................................7

Manual Registration ..........................................................................................8

De-Registration ..............................................................................................10

Verification Tone ..............................................................................................11

Site Survey Mode............................................................................................12

Serial Repeater ID Programming....................................................................13

Before Requesting Help..................................................................................15

Technical Information ......................................................................................16

Guarantee ......................................................................................................17

Index ..............................................................................................................18

QUQX00130YA_01_A 20/1/04 6:40 pm Page 2

Operating Instructions | 3

Overview

Arepeater is used when you need to extend the range of your cordless DECT

telephone or PBX cell station, to include areas where reception was previously not

available. The repeater extends the range in all directions, allowing several floors to

be covered.

Up to 6 repeaters can be registered at a DECT base unit, and up to 18 repeaters

can be registered at a PBX cell station (when utilising Serial Repeater ID

Programming).

Please note : The number of simultaneous calls on a Cell Station is reduced by

adding a repeater. This is by design. Each repeater is controlled using one speech

path. The repeater can support up to a maximum of two handsets.

Compatibility

The Panasonic DECT repeater is:-

•Compatible with selected Panasonic consumer DECT products. Please refer to your

repeater packaging or your DECT operating instructions for compatibility

information.

•Capable of providing full handover with TDA PBX products plus TD1232/TD816 with

TD7590 (a software upgrade may be necessary).

•Designed to be used as a range extender (no handover) using TD7580.

•Designed to be used as a range extender (no handover) using TD7590 (without the

software upgrade).

General Safety

•Only use the power supply included with the product.

•Do not connect the AC adaptor to any AC outlet other than the standard AC220-

240V.

•The apparatus is approved for use with PQLV19E, PQLV19AL and PQLV19CE

power supply.

•This apparatus will restrict emergency telephone calls from portable handsets linked

through the repeater under the following conditions:

•The portable handset batteries need recharging or have failed.

•During a mains power failure.

•When the key lock of the portable handset is set to ON.

•When the handset is in direct call mode.

•Do not open the repeater.

•This apparatus should not be used near emergency/intensive care medical

equipment and should not be used by people with pacemakers.

•Care should be taken that objects do not fall, and liquids are not spilt onto the unit.

Do not subject this unit to excessive smoke, dust, mechanical vibration or shock.

QUQX00130YA_01_A 20/1/04 6:40 pm Page 3

4|Operating Instructions

Environment

•Do not use this unit near water.

•This unit should be kept away from heat sources such as radiators, cookers, etc. It

should also not be placed in rooms where the temperature is less than 5ºC or

greater than 40ºC.

•The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is

located near the unit and is accessible.

WARNING: TO PREVENT THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE

THE PRODUCT TO RAIN OR ANY OTHER TYPE OF MOISTURE.

Accessories (Included)

•AC Adaptor

PQLV19E (UK only)

PQLV19AL (Australian)

or PQLV19CE (European)

• Repeater

KX-A272

•Quick Setup Guide

QUQX00112Y

•Operating Instructions (on CD-ROM)

QUQX00117Y

•Screw Pack

OR OR

QUQX00130YA_01_A 20/1/04 6:40 pm Page 4

Operating Instructions | 5

Wall Mounting

This unit can be mounted on a suitable wall or placed on a flat surface.

•Insert screws into wall. Avoid pipes and electrical cables etc. that may be

present/buried. The centre of the screws must be 71mm apart. Allow a protrusion of

2mm from the base of the screw head to the wall, using the washer provided (see

diagram below).

•Arrange the AC cord as shown, then mount the unit (4 possible routes available).

Connection

•Plug in the AC adaptor to the rear of the unit, and fasten the AC cord to prevent it

from being disconnected.

•The AC adaptor must remain connected at all times. (It is normal for the adaptor to

feel warm during use).

LED

Switch

Screw

Head

Washer

Wall

71mm

DC Jack

Cord from AC

adaptor

QUQX00130YA_01_A 20/1/04 6:40 pm Page 5

6|Operating Instructions

Placement

To get the best performance from the repeater:

•Select a raised position (on wall etc), which is well within range of the Base

Unit/Cell Station.

•Avoid positioning the repeater close to objects that will interfere with reception, such

as thick walls, radiators, metal shelving etc.

•For maximum distance noise-free operation, place your DECT repeater away from

electrical appliances such as TV, radio, personal computer or other telephone

equipment.

•Keep a minimum distance of 10m between repeaters.

•If the Green LED flashes - move the repeater closer to the Base Unit/Cell Station or

away from obstructions etc.

LED Status

Red LED (Indicates special states)

Green LED (Indicates registration / communications states)

On/off/blink specification Definition

On Repeater is not assigned to any system

Off Normal Operation

Slow blinking - “320ms on / 320ms off” Manual registration mode

Intermittent blinking “100ms on / 2.4sec off” Verification mode (Flashes in time with monitor beep

tone)

On/off/blink specification Definition

On Repeater successfully registered

Off Repeater de-powered

Slow blinking - “320ms on / 320ms off” Registration process ‘searching’ for Cell Station /

unregistered

Fast blinking - “200ms on / 200ms off” Repeater ID programming mode / Site Survey mode

(PBX application only)

QUQX00130YA_01_A 20/1/04 6:40 pm Page 6

Operating Instructions | 7

Automatic Registration

Automatic registration cannot be performed if the repeater is already registered to

another base unit or cell station. Please follow the DE-REGISTRATION procedure

on page 10 before attempting Automatic Registration.

•Ensure that the repeater is switched off

(disconnect the AC adaptor) (both LEDs are

OFF).

•Place your DECT base unit into registration mode by pressing and holding the ÏÏ

button for 10 seconds. This step is not necessary for registration to PBX cell

stations.

•Power on the repeater, by connecting the AC

adaptor. The red LED will light for 2 seconds,

and then the green LED will flash slowly. This

indicates that the repeater is searching for

the cell station or base unit.

•When the repeater has found the cell station

or base unit, the green LED will go steady

ON.

Note: It may take up to 60 seconds for the

repeater to register with the cell station or

base unit.

•If after 60 seconds the registration has not

completed, the red LED will go steady ON,

indicating that registration has been

unsuccessful. In this case the registration

must be repeated. Power off the repeater and

start again.

•Please note :1) Manual registration procedure may be required if the repeater is

used with unlisted products.

2) We recommend that you power down any cell station that you do

not wish to connect to the Repeater prior to Registration.

QUQX00130YA_01_A 20/1/04 6:40 pm Page 7

8|Operating Instructions

Manual Registration

There must be at least one handset already registered to the base unit or cell

station to carry out manual registration.

•Ensure that the repeater is switched off

(disconnect the AC adaptor) (both LEDs are

OFF).

•Power on the repeater, by connecting the AC

adaptor. The red LED will light for 2 seconds,

and then the green LED will flash slowly.

•Hold down the repeater switch for 3 seconds.

The green LED and the red LED will flash

alternately.

•Place your DECT base unit into registration mode by pressing and holding the ÏÏ

button for 10 seconds. This step is not necessary for registration to PBX cell

stations.

•When the repeater has found a suitable cell

station or base unit, the green LED will flash

quickly.

•Please note :1) We recommend that you power down any cell station that you do

not wish to connect to the Repeater prior to Registration.

QUQX00130YA_01_A 20/1/04 6:40 pm Page 8

Operating Instructions | 9

Manual Registration continued.

•Press ‘off hook’ on the handset. The

green LED will go steady ON.

•Enter a unique identifying number on the handset keypad for each repeater

registered. The identifying number can be 2 to 7 for domestic DECT products,

and 000 to 255 for PBX DECT products. The digit will display on the handset

screen.

•The green LED will flash to correspond

with the dialled digit. i.e digit 5 will

cause the green LED to flash 5 times.

For PBX use the digit 0 will cause the

green LED to flash 10 times. i.e digits

025 will cause the green LED to flash

10 times for ‘0’, then a delay of 2

seconds, then flash 2 times for ‘2’, then

a delay of 2 seconds, then flash 5 times

for ‘5’. You do not have to wait for the

confirmation flashes when registering.

•Dial “*” on the handset to store the

identifying number to memory. The

green LED will go off for 1 second.

If the identifying number entered is

already assigned, the red LED will light

for 1 second. A new identifying number

must then be entered followed by “*”.

The green LED will then flash slowly for

a short period of time before going

steady ON. Registration is complete.

•If the registration is not successful, the red

LED will turn steady ON. In this case, repeat

the registration process.

QUQX00130YA_01_A 20/1/04 6:40 pm Page 9

10 | Operating Instructions

De-Registration

In order to perform de-registration, the repeater must have already been registered

to a base unit or cell station.

•Ensure that the repeater is switched off

(disconnect the AC adaptor) (both LEDs

are OFF).

•While holding down the repeater switch,

power on the repeater by connecting

the AC adaptor. Continue to hold down

the repeater switch for 10 seconds. The

red LED will flash slowly.

•After 10 seconds the red LED will go

steady ON. The Repeater is now de-

registered successfully.

•To re-register the repeater, please follow the normal registration process.

QUQX00130YA_01_A 20/1/04 6:40 pm Page 10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Reloj de repetición de Panasonic

Panasonic

Panasonic WX-CR480P Manual de usuario

Panasonic

Panasonic KX-A405 Manual de usuario

Panasonic

Panasonic VL-FAN2 Manual de usuario

Panasonic

Panasonic VL-FKD2 Manual de usuario

Panasonic

Panasonic KX-A406 Manual de usuario

Panasonic

Panasonic WX-CR470 Manual de usuario

Panasonic

Panasonic VL-FKD2AZ Manual de usuario

Panasonic

Panasonic VL-FKD2 Manual de usuario

Panasonic

Panasonic VL-FKD2EX Manual de usuario

Panasonic

Panasonic KX-A407 Series Manual de usuario

Panasonic

Panasonic KX-A405 Manual de usuario

Panasonic

Panasonic WX-CR470 Manual de usuario

Panasonic

Panasonic A406 Manual de usuario

Panasonic

Panasonic AJRP900 - DIGITAL TRIAX REPEAT Manual de usuario

Panasonic

Panasonic KX-A405 Manual de usuario

Panasonic

Panasonic VL-FAN1BX Manual de usuario

Panasonic

Panasonic WX-CR470 Manual de usuario

Panasonic

Panasonic KX-HNH200 Manual de usuario

Panasonic

Panasonic VL-FKD2BX Manual de usuario

Panasonic

Panasonic AJ-RP900P Manual de usuario

Panasonic

Panasonic KX-A406 Guía de instalación y uso

Panasonic

Panasonic KX-TGA405EX Manual de usuario

Panasonic

Panasonic KX-A406 Manual de usuario

Manuales populares de Reloj de repetición de otras marcas

Gigaset

Gigaset 108 Manual de usuario

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Manual de usuario

Kenwood

Kenwood TKR-750-850 Manual de lista de piezas

Asus

Asus RP-AC51 Manual de usuario

Exibel

Exibel HRP0101 Manual de usuario

Kidde

Kidde Vega Manual de usuario

Telcosat

Telcosat RBB 850 Guía de instalación

York

York Universal LINC485 Manual de usuario

MIKOM

MIKOM MRx01B Power Series Manual de usuario

Simrad

Simrad RD 301 Manual de usuario

Tait

Tait TB7304 Manual de usuario

R-tron

R-tron RSN-CDMA-37-C Manual de usuario

Inventronics

Inventronics DALI REPEATER SO Manual de usuario

XFP

XFP 16 Manual de usuario

Andrew

Andrew MRx18 Manual de usuario

COMBA

COMBA RXA3748 Manual de usuario

ADRF

ADRF SDR-ICS-43 Manual de usuario

Teltonika

Teltonika WRP100 Manual de usuario