Panasonic HD-PLC DA-PU100 Manual de usuario

Operating Manual

PLC Adaptor

Model No. DA-PU100

• Thank you for purchasing this Panasonic

product.

•Please read this Operating Manual

carefully before installing the product.

• Keep all documentation in a safe place for

future reference.

• To obtain the Installation Manual, contact

your dealer.

• This product is compatible with "HD-PLC

multi-hop technology".

Things you should keep a record of:

Date of purchase

Model number

Serial number

Dealer’s name and address

Dealer’s telephone number

Table of Contents

For Your Safety 2

Introduction 4

Precautions 5

Location of controls 6

Connection of power supply 7

Appendix 8

PNQX8788ZA P0718AG0

Printed in Vietnam

For Your Safety

To prevent severe injury and loss of life, read this section carefully before using the product

to ensure proper and safe operation.

• The following types of symbols are used to describe the level of injury and/or damage

that may occur if the product is used incorrectly.

• The following types of symbols are used to classify and describe the type of instructions

to be observed. (The following symbols are examples.)

This type of symbol is used to

alert operators to actions that

must not be performed.

This type of symbol is used to

alert operators to a procedure

that must be performed.

WARNING

Denotes a potential hazard that could result in

serious injury or death.

• Do not install the product near medical devices, and do not connect it to the

same power line as a medical device. If high-frequency signals from the

product affect the medical equipment, it may cause malfunction and

accidents.

• Keep the screws, fixing brackets, USB connector cap, LAN connector cap,

RS-485 terminal, and terminal cover out of reach of children to prevent

swallowing.

• Do not damage the terminals.

• Do not get the product wet.

• Do not install or inspect the product with wet hands.

• Do not touch the product during a thunderstorm.

• Do not disassemble or alter the product.

• Do not put metal or foreign objects inside the product.

• Do not drop the product or subject it to strong impacts.

• Do not overload the AC outlets and extension cords.

• Do not disassemble the product.

• Be sure to attach the terminal cover. High voltage can cause fire or electric

shocks.

• Install, inspect, and repair the product only after disconnecting it from power.

• After installation, ensure the area around the product is safe.

• Only qualified electrical workers may install, inspect, and repair the product.

• Fasten the terminal screw firmly with the appropriate torque.

• Install the product in the distribution box.

• Cut the circuit breaker immediately if the product emits smoke, overheats, or

produces abnormal smells or noises. Use a certified circuit breaker with a

contact gap of 3 mm (0.12 in.) or more, and install it near this product.

CAUTION

Denotes hazards that could result in minor injury or

damage to the product.

• Do not install the product in a location that is subject to large amounts of

water, humidity, dust, or soot (such as in a kitchen or near a humidifier), nor in

a location where corrosive gases (such as ammonia, hydrogen sulfide, or

chlorine) are present.

• Do not install the product in a location that is unstable or subject to heavy

vibrations.

• Keep away from fire.

• Disconnect the power when the product will not be used for an extended

period of time, or when the product will be inspected.

• Disconnect the power if the product falls or becomes damaged.

• Be sure to secure the product with all 3 of the fixing brackets.

• Confirm the strength of the mounting location. Consider whether the

mounting location is strong enough to hold the product for an extended

period of time. A weakening of the mounting location may lead to the product

falling. The mounting location must be able to support a force of 12.26 N

(1.25 kgf) or more at each screw position. If the mounting location does not

provide sufficient support, it must be reinforced to provide sufficient support,

or falling prevention measures must be taken. If the product will be installed

150 cm or higher off the floor, be sure to take falling prevention measures.

• When mounting the product, ensure that the metal parts of the product, such

as the fixing screws, do not come into contact with other metal parts.

• If you stop using the product, remove the product from the distribution box to

eliminate the risk of falling.

• Ensure that the environment inside the distribution box meets the

temperature and humidity requirements.

Introduction

Check that all accessories are included before installing the product.

PLC Adaptor (1)

Fixing brackets (3)

Small fixing screws (3)

Large fixing screws (3)

Operating Manual (this manual) (1)

Precautions

• This product is for indoor use only.

• Panasonic is not responsible for any loss of data and other direct or indirect damage

caused by external factors such as power failures or noise on electrical wiring.

• This product may be a source of electrical interference for the following devices:

–Other PLC devices that use different transmission methods

–Remote controlled devices using radio waves

–Short wave radios, lights with dimmers, touch lamps, wireless mice, etc.

• If this device interferes with other products, try the following countermeasures:

–If this device interferes with short wave radios:

• Keep the short wave radio away from the wall.

• Use a different frequency.

• Certain electrical devices emit electrical noise. If this noise is passed on to the electrical

wiring, it may interfere with the performance, speed, and reliability of the product. We

recommend connecting an electrical noise filter to noise emitting devices.

Note

• The following devices are most likely to emit noise:

–Other PLC devices that use different transmission methods

–Battery chargers (including cell phone chargers), AC adaptors (for modems, routers,

laptop PCs, etc.), hair dryers, vacuum cleaners, power drills, lights with dimmers, and

touch lamps.

• Do not connect the product to a power outlet with a noise filter or a surge protector.

• This product transmits data over existing electrical wiring. Electrical noise, the length of

the wiring, and the specification of the circuit breaker may be causes of interference.

Also, if there is strong radio equipment nearby, it may cause low speeds or disrupt

communication.

• If the wiring from the product is too long, data communication may be affected.

• Do not connect the product to a backup power supply device, such as a UPS

(uninterruptable power supply).

• Keep the product away from devices with a magnet. They may interfere with the product.

• Do not place the product near air conditioners or heaters. They may damage the product.

• Graphical symbols on the product.

～Alternating current Double insulation

Location of controls

Unit

With the terminal cover removed

MASTER indicator: Indicates whether the product is a MASTER or TERMINAL.

LAN indicator: Indicates the status of the LAN connection.

PLC indicator: Indicates the status of the PLC link.

SET UP button: For details, refer to the Installation Manual.

USB connector

RS-485 terminal

DIN rail lever: Pull the lever in the direction of the arrow to release the product from the

DIN rail.

LAN connector

RESET button: Resets the product.

CLEAR button: Restores the factory default settings.

Terminal cover

Terminal cover screws

Holes for fixing screws

Power terminal (N phase)

Power terminal (L phase)

The state of each indicator

MASTER indicator On (green)*1 Operating as PRIMARY MASTER.

On (orange)*1 Operating as SECONDARY MASTER.

Off Operating as TERMINAL.

LAN indicator Blinking Connected to the LAN.

PLC indicator On (green)*1 Connected to a PLC device.

On (orange)*1 Connected to power, but not connected to

a PLC device.

Off Power is not connected.

*1 After turning on the power, the LED lights steady for 8 hours, and then blinks after that.

If you press the SET UP button, the LED lights steady for 1 minute, and then blinks after

that.

Connection of power supply

Follow this procedure to wire the product to the distribution box.

1. Remove the terminal cover.

2. Wire the L phase of the power line to terminal L ( ) and the N phase to terminal N

( ).

• Applicable AWG value is 20 - 14. Use certified or equivalent wires for the electric

wires of this product.

3. Attach the terminal cover.

• For other details, please refer to the Installation Manual.

Appendix

Troubleshooting

Symptom Possible Cause Remedy

None of the

indicators light

or blink.

Power is not connected. Connect a power source.

The product might be

malfunctioning.

If the PLC indicator does not

light, contact your dealer.

The PLC

indicator lights

or blinks

orange.

Another product is not turned on. Turn on another device set to

operate as the master or a

terminal device.

A power strip with a noise filter or

surge protector is being used.

If you are using a power strip,

use one that does not include a

noise filter or surge protector.

A power strip with a long power

cord is being used.

Use a power strip whose power

cord is as short as possible.

Due to the wiring conditions

between PLC adapters or the

effects of noise, the PLC signal is

not reaching its destination.

Reevaluate the installation

locations, or add another PLC

adapter (relay unit) to the power

wires on the transmission route.

The LAN

indicator does

not light.

A LAN cable is not connected. Check the connection of the LAN

cable.

The network device is not turned

on.

Turn on the network device.

The wired connection function of

a network device is not enabled.

Disable the wireless connection

function of the device, and

enable the wired connection

function.

The PLC

indicator lights

red.

The product's operation might be

frozen.

Either turn off the power and

then turn it on again, or press

and hold the RESET button for at

least 1 second.

Factory Reset

This function will erase all of the settings in this product and initialize it to the factory default

settings.

1. Connect the product to a power source.

2. Press and hold the CLEAR button for more than 3 seconds.

Notice

• After the indicators light, wait at least 30 seconds before terminating power to the

product.

Specifications

Unit

Operating

environment

Temperature: -25 ℃ – 60 ℃ (-13 ℉ – 140 ℉)

Humidity: 20 % RH – 85 % RH (No condensation)

Degree of protection

from solid objects

IP5X

External dimensions Width × Height × Depth (Approx.):

75 mm × 102 mm × 47 mm (2.95 in. × 4.02 in. × 1.85 in.)

(Unit only. Not including protrusions.)

Weight Approx. 260 g (0.57 lb.) (Unit only)

Power requirements AC 100 – 240 V, 50/60 Hz

Power consumption Avg. 4 W, Max. 7 W (100 V)

Avg. 6 W, Max. 8.5 W (240 V)

Interface PLC port*1 / Ethernet port*1 / RS-485 port*1 / USB port*1

Protocol TCP/IP / DHCPc / HTTPd: IPv4 / IPv6

SNMP/MIB: IPv4

*1 1ch

PLC port

Standard HD-PLC multi-hop

Multi-hop 10

Communication

speed

240 Mbps*1

Frequency band 2 MHz – 28 MHz

Modulation method Wavelet OFDM (2 PAM - 32 PAM)

Access method CSMA/CA

Error correction Reed-Solomon encoder/decoder

Convolutional encoder/Viterbi decoder

LDPC-CC (Low Density Parity Check-Convolutional Codes)

Security AES 128-bit encryption

Communication

distance

Approx. 200 m (656 ft)*2 between PLC adaptors

Otros manuales para HD-PLC DA-PU100

Tabla de contenidos

Otros manuales de Receptor de Panasonic

Panasonic

Panasonic TUIRD20 - DSS RECEIVER Manual de usuario

Panasonic

Panasonic SA-HE70S-U Operating Manual de usuario

Panasonic

Panasonic SA-HE75E Manual de usuario

Panasonic

Panasonic SA-DT300E Manual de usuario

Panasonic

Panasonic CF-AA5713A Series Manual de usuario

Panasonic

Panasonic BL-PA100A - HD-PLC Ethernet Adaptor Manual de usuario

Panasonic

Panasonic TUIRD20 - DSS RECEIVER Manual de usuario

Panasonic

Panasonic RF-2400D Manual de usuario

Panasonic

Panasonic RF-SW50 Manual de usuario

Panasonic

Panasonic DNUA-P75 Manual de usuario

Panasonic

Panasonic TU-DST52F Manual de usuario

Panasonic

Panasonic CZ-CAPRA1 Manual de usuario

Panasonic

Panasonic CQ-C3403W Manual de usuario

Panasonic

Panasonic AG-IA232TC-E Manual de usuario

Panasonic

Panasonic SA-XR50S Manual de usuario

Panasonic

Panasonic CQ-VD5505W Manual de usuario

Panasonic

Panasonic SAHE9 - RECEIVER Manual de usuario

Panasonic

Panasonic SHFX71 - WIRELESS SYSTEM Manual de usuario

Panasonic

Panasonic RF-B65D Manual de usuario

Panasonic

Panasonic SAXR70 - RECEIVER Manual de usuario

Panasonic

Panasonic WVRC100 - BROADCAST RECEIVER Instrucciones de funcionamiento

Panasonic

Panasonic SAHE9 - RECEIVER Manual de usuario

Panasonic

Panasonic RAMSA WX-RP700 Manual de usuario

Panasonic

Panasonic PS-550SU Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario