Panasonic CZ-RWRL3 Manual de usuario

English

Read through the Installation Instructions before you proceed

with the installation.

In particular, you will need to read under the “Safety

Precautions” on page 3.

Contents

Part Names................................................... 2

Supplied accessories.................................. 2

Safety Precautions ...................................... 3

Specications .............................................. 5

Installation Precautions.............................. 6

Wiring ........................................................... 7

Mounting ...................................................... 8

Resin Panel...................................................... 8

Metal Panel ...................................................... 9

Setting ........................................................ 10

Address Setting.............................................. 10

Test Operation ........................................... 11

Self-diagnostics table and

detected contents........................................... 12

Installation Instructions

Infrared Receiver for L

Model No. CZ-RWRL3

2(EN)

Part Names

Receiver

(1) Indication lamp

Indicates operation status.

(2) Light receiving section

Receives signals.

Operation panel

(3) Emergency operation button

Starts/Stops emergency operation.

Supplied accessories

< >: Number of pieces

Installation Instructions

<1>

Installation Instructions

Disc

<1>

Screw M4 × 10

<4>

Clamper

<3>

(EN)

Safety Precautions

We assume no responsibility for accidents

or damages resulting from methods other

than those described in the installation

instructions or methods without using

specied parts.

Malfunctions that occurred due to the

unauthorised installation methods are not

covered by the product warranty.

 Read the installation instructions supplied

with indoor units as well.

 After the installation is complete,

perform test operation to conrm that no

abnormality is present.

 When relocating or repairing this receiver,

provide the Installation Instructions to the

servicing personnel.

 Do not clean inside the receiver by users.

Engage authorised dealer or specialist

for cleaning.

WARNING

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

CAUTION

This symbol refers to a hazard or unsafe

practice which can result in personal injury or

product or property damage.

WARNING

 Turn off the circuit breaker of

the units before installation.

 This receiver shall be installed

in accordance with National

Wiring Regulations.

 Connect and x the specied

cables for wiring securely.

 Do not allow the connection

to be exposed to the external

force of the cables.

 Select an installation location

which is rigid and strong

enough to support or hold the

receiver, and select a location

for easy maintenance.

 This receiver must not be

modied or disassembled

under any circumstances.

Modied or disassembled

receiver may cause re,

electric shock or injury.

Read before installation

This receiver must be installed by the sales dealer or installer.

These instructions are all you need for most installation sites and maintenance conditions.

If you require help for a special problem, contact our sales/service outlet or your certied

dealer for additional instructions.

4(EN)

NOTICE The English text is the original instructions. Other languages are translation of

the original instructions.

CAUTION

 Do not use the receiver at the

following locations.

• Location where ammable

gases, etc. may leak

• Location where corrosive

gases, etc. may leak

• Location with lots of water

or oil droplets (including

machine oil)

• Location where droplets of

organic solvents spread

• Location where acidic or

alkaline solutions or special

sprays are frequently used

 Do not wash with water.

 Do not operate with wet

hands.

Safety Precautions

Disposal of Old Equipment

Only for European Union and countries with recycling systems

This symbol on the products, packaging, and/or accompanying documents means that

used electrical and electronic products must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to

applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment. For more information

about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

(EN)

Specications

Model No. CZ-RWRL3

Dimensions Receiver: (H) 37 mm × (W) 70 mm × (D) 22 mm

Operation panel: (H) 55 mm × (W) 120 mm × (D) 16 mm

Weight Receiver: 15 g

Operation panel: 75 g

Temperature /

Humidity range

0 °C to 40 °C / 20% to 80% (No condensation)

*Indoor use only.

Power Source DC16 V (supplied from indoor unit)

6(EN)

Installation Precautions

 The receiver uses a very weak infrared light for its signal, which can result in the signal not being

received because of the following inuences, so take care in where the indoor unit is installed.

• Inverter or rapid-start type uorescent lights (Models without glow lamps)

• Plasma display or LCD televisions

• Direct sunlight or other sources of bright light

 Do not bundle together with the power source wiring or store in the same metal tube. Operation

error may occur.

 Be careful not to connect cables to other terminals of indoor units (e.g. power source wiring

terminal). Malfunction may occur.

 Avoid the following locations for installation.

• Location where condensation occurs

• Location where voltage uctuation frequently occurs

• Location where there is a machine producing electromagnetic radiation

(EN)

Wiring

1 Connect the receiver and the operation panel with the receiver wiring.

2 Connect the wires from the receiver to the terminals for RC wiring on the indoor unit.

Wiring Diagram

Receiver

wiring

Operation panel

Indoor unit

CN001

2P white

Terminals for RC wiring

RC wiring

• No polarity

CN002

6P white

CN001

6P white

Infrared Receiver for L

Installation when setting Main/Sub for the remote controller and the receiver

It is possible to operate one or more indoor units using two remote controllers.

After installation, set one to [Main] and the other to [Sub].

When using the infrared remote controller and the wired remote controller in combination, set the

wired remote controller to [Main].

R1 R2

12 CN001

R1 R2 R1 R2 R1 R2

12 CN001

Indoor unitIndoor unit Indoor unit Indoor unit

Terminals for

RC wiring

• No polarity

Receiver

(Sub)

Wired RC

(Main)

Receiver

(Sub)

Wired RC

(Main)

Using 1 indoor unit Using more than 1 indoor unit

Note

 The receiver can be connected to any indoor unit for operation.

 Multiple infrared remote controllers cannot be used simultaneously for a single indoor unit.

 Wiring connected via remote controllers is prohibited.

 Also see the “Installation Instructions” supplied with the indoor unit or wired remote controller when

performing remote control with the main and sub remote controllers or group-controlling.

8(EN)

Mounting

See “Setting” before mounting.

Resin Panel

Installing the Operation Panel

1 Remove the 2 screws. Then remove the cover A from the back of the panel. (Fig. A)

2 Fasten the operation panel to the location shown in the gure below with the 2 supplied screws.

(Fig. B)

3 Pass the receiver wiring through the back of the panel.

Operation panel

Receiver wiring

(6P white connector)

Supplied screws

Fig. A Fig. B

Cover A

Installing the Receiver

1 The cover B comes attached to the panel. Remove the 1 screw and detach it by pressing from the

front side of the panel. (Fig. C)

2 Connect the receiver wiring that is sticking out from the operation panel to the receiver and t the

receiver into the panel. Make sure the 6P white connector is fully plugged in all the way.

3 Bend the lead wire of the receiver into shape so that it does not come in contact with the louver

shaft. There is a groove to pass the wire (circled part in Fig. C). Insert the lead wire into this groove

with no slack.

4 Attach the cover A until it is rmly engaged in the claws indicated by arrows. (Fig. D)

5 Arrange the lead wire of the operation panel appropriately and fasten it with the supplied clamper.

6 Install the ceiling panel.

Connect

Receiver

Fig. C Fig. D

Cover B

 For more wiring information, see the section “Wiring”.

(EN)

Mounting

Metal Panel

Installing the Operation Panel

1 Remove the 2 screws and remove the cover A from the back of the panel. (Fig. A)

2 Fasten the operation panel to the location shown in the gure below with the 2 supplied screws.

(Fig. B)

3 Pass the receiver wiring through the back of the panel.

Operation panel

Receiver wiring

(6P white connector)

Loop extra wiring and

fasten with a twist lock.

Supplied screws

Fig. A Fig. B

Cover A

Installing the Receiver

1 The cover B comes attached to the panel. Spread the points as indicated in gure C and remove it.

The tape holding cover B is only to protect it during transport. Remove and discard it.

2 Connect the receiver wiring that is sticking out from the operation panel to the receiver and t the

receiver into the panel. Make sure the 6P white connector is fully plugged in all the way.

3 Pass the lead wire for the receiver through the cutout in the panel and the hole in the metal panel.

Then fasten it to the hole in the metal panel with the supplied clamper. (Fig. D)

4 Attach the cover A.

5 Properly route the lead wire of the operation panel and fasten it with the twist lock. (Fig. B)

6 Install the ceiling panel.

Connect

Receiver

Fig. C Fig. D

Cover B

Fasten the lead wire to

hole in metal panel

Pass through cutout

Spread

 For more wiring information, see the section “Wiring”.

10 (EN)

Setting

Before installing the operation panel, check the settings of the operation panel switches.

Main/Sub switch (4)*

OFF: Main

ON: Sub

Factory default: OFF (1 – 4)

Address switch (1 – 3)

* When using the infrared remote controller and the wired remote controller in combination, set the

wired remote controller to [Main].

Address Setting

 When more than 1 receiver is installed in the same room, setting addresses prevents interference.

 For how to change addresses of infrared remote controllers, see the operating instructions of

infrared remote controllers.

Infrared remote

controller

address display

Address Address Address Address Address Address Address ON/OFF

States

ALL123456

Infrared

receiver

address switch

positions

Receiving is

possible at

all address

positions.

123412341234123412341234OFF ON

Tabla de contenidos

Otros manuales de Receptor de Panasonic

Panasonic

Panasonic WVRC150 - CONTROLLER Manual de usuario

Panasonic

Panasonic TUIRD20 - DSS RECEIVER Manual de usuario

Panasonic

Panasonic CZ-CAPRA1 Manual de usuario

Panasonic

Panasonic SAHE7 - RECEIVER Manual de usuario

Panasonic

Panasonic RF-SW250 Manual de usuario

Panasonic

Panasonic CQ-4400U Manual de usuario

Panasonic

Panasonic RF-P150D Manual de usuario

Panasonic

Panasonic SAXR70 - RECEIVER Manual de usuario

Panasonic

Panasonic CQ-C1305U Manual de usuario

Panasonic

Panasonic SA-G90 Manual de usuario

Panasonic

Panasonic RAMSA WX-RP700 Manual de usuario

Panasonic

Panasonic TZ-DBS01B Manual de usuario

Panasonic

Panasonic CQ-VW120W Manual de usuario

Panasonic

Panasonic DMREZ485V - DVD RECORDER - MULTI LANGUAGE Manual de usuario

Panasonic

Panasonic K-SRC14 Manual de usuario

Panasonic

Panasonic SAXR58 - DIGITAL A/V RECEIVER Manual de usuario

Panasonic

Panasonic CQDF903U - Sirius® Radio-Ready CD... Manual de usuario

Panasonic

Panasonic CY-TM200NA Manual de usuario

Panasonic

Panasonic CZ-CFUNC2 Manual de usuario

Panasonic

Panasonic SA-XR10 Manual de usuario

Panasonic

Panasonic WVRC150 - CONTROLLER Instrucciones de funcionamiento

Panasonic

Panasonic CF-AA5713A Series Manual de usuario

Panasonic

Panasonic SAHE7 - RECEIVER Manual de usuario

Panasonic

Panasonic CQ-C8352N Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario