Panasonic ET-D3QW200 Manual de usuario

Thank you for purchasing this Panasonic product.

■To ensure correct use of this lens, please read the operating instructions supplied

with the lens and the projector carefully.

■Before using this product, be sure to read “Read this rst!” (Page 3).

■Please save this manual for future use.

Commercial Use

Model No. ET-D3QW200

DPQX1563ZA/X1

Zoom lens

Operating Instructions

ENGLISH

FRANÇAIS

日本語

2-ENGLISH

Read this rst! ......................................................................................3

Before Use.............................................................................................5

Preparation............................................................................................5

Before replacing the projection lens........................................................ 5

Attaching and Detaching the Lens .......................................................... 5

Peripheral focus adjustment function ...................................................... 6

Lens calibration ....................................................................................... 7

Projection relationships.......................................................................8

Lens shift ranges................................................................................12

Specications .....................................................................................13

Dimensions .........................................................................................13

Projected image size and Projection distance.......Appendix / Annexe / 付録 1

The "Appendix" can be found after the Japanese language section ( 日本語 ).

█ Contents

ENGLISH-3

Read this rst! Always follow these precautions

WARNING:

Do not look at or place your skin into the light emitted from the lens while the

projector is being used.

Doing so can cause burns or loss of sight.

zStrong light is emitted from the projector’s lens. Do not look at or place your hands

directly into this light.

zTurn off the power when moving away from the projection lens or projector.

Do not project an image with the lens cover attached.

zDoing so can cause re.

CAUTION:

Before replacing the projection lens, be sure to turn off the power and

disconnect the power plug from the wall outlet.

zUnexpected projection of light may cause injury to eyes.

zReplacing the projection lens without removing the power plug may result in electric

shock.

Do not stand in front of the lens while the projector is being used.

Doing so can cause damage and burns to clothing.

zStrong light is emitted from the projector’s lens.

Do not place objects in front of the lens while the projector is being used.

Doing so can cause re, damage to the object, or malfunction of the lens and

projector.

zStrong light is emitted from the projector’s lens.

Do not open the desiccant bag. Do not eat the contents.

Inadvertently ingesting desiccant could be harmful.

zIf the desiccant gets into your eyes or mouth, immediately rinse with plenty of water

and seek medical attention.

zKeep desiccant out of the reach of children.

4-ENGLISH

Read this  rst! (continued)

■Hazard distance (IEC 62471-5:2015)

The distance from the projection lens surface, at which the emission reaches the

Accessible Emission Limit (AEL) of risk group 2, is known as the hazard distance (HD)

or safety distance. The area where the emission exceeds the Accessible Emission Limit

of risk group 2 is called the hazard zone (HZ).

Within the hazard zone, never look into the light projected from the projector. The eyes

may be damaged by direct irradiation even if you look at the light just for a moment. If

you are outside the hazard zone, it is considered to be safe in all circumstances except

deliberately staring into the light projected from the projector.

HZ HZ

■Risk group

The combination of the projector and the projection lens is categorized as risk group 2

when the hazard distance is 1 m (39-3/8") or less. It is categorized as risk group 3 when

the hazard distance exceeds 1 m (39-3/8"), and it will be for professional use instead of

consumer use.

In case of risk group 3, there is a possibility of damaging the eyes by direct irradiation

when looking into the projection light from inside the hazard zone even for a moment.

In the case of risk group 2, safe use without damaging the eyes is possible in all

circumstances except deliberately staring into the light projected from the projector.

The risk group for the combination of the projection lens and a compatible projector is as

follows.

Projector model Risk group

PT-RQ50K Risk group 2

ENGLISH-5

This zoom lens is a projection lens equipped with an EEPROM*1 and stepping motor.

*1 EEPROM: Electrically erasable programmable read-only memory

■Supported projectors

PT-RQ50K

Note

zSome of the alphabet letters at the end of projector model numbers may be omitted in this manual.

zModels other than the above may also be supported. Refer to the operating instructions for

your projector or the Panasonic website (https://panasonic.net/cns/projector/).

■Supplied Accessories

Make sure that the following has been provided.

Part name Appearance

Lens cover

zThe product is delivered

with a lens cover attached.

1 each for front and rear

Before Use

Preparation

Before replacing the projection lens

Return the projection lens to the home position before replacing or removing it.

For details on how to return the lens to the home position, refer to the operating instructions

of the projector.

Attention

zMake sure that the projector power supply is switched off before attaching or detaching the

projection lens.

zAfter removing the projection lens, store it safely away from vibration or impacts.

zDo not touch the electrical contacts of the projection lens with your fingers. Dust and dirt on

the contacts may cause contact malfunctions, while static electricity may damage the unit.

zDo not touch the surface of the lens with bare hands. Finger prints and dirt on the surface

of the lens will be magnified by the lens and lower the quality of the projected image. Place

the supplied lens cover on the zoom lens when the projector is not in use.

zThe lens is made of glass. The lens could be damaged if brought into contact with or

rubbed against hard objects. Handle the lens carefully.

zUse a clean, soft and dry cloth to wipe away dust and dirt from the projection lens.

Do not use fluffy cloths containing oil, water or dust for cleaning. The lens is easily

damaged, so do not apply excessive pressure when wiping it.

Attaching and Detaching the Lens

For details on attaching and detaching the projection lens, refer to the operating instructions

of the projector.

6-ENGLISH

Preparation (continued)

Peripheral focus adjustment function

When yo

u change the size of the projected image, the focal balance between the center

and peripheral areas of the screen may shift. This shift in balance tends to increase

proportionally with smaller throw ratios.

The ET-D3QW200 is equipped with a peripheral focus adjustment function to correct the

shift

in focal balance between the center and peripheral areas of the screen.

1) Turn the peripheral focus

adjustment ring in the

direction of the arrow to

match the projection distance

displayed on the lens to the

actual distance from the lens

to the screen.

2) Operate the projector to align

the focus of the center of the

projected image.

Note

zThe projection distances displayed on the lens are approximate guides.

zThe lens focus is not stable immediately after powering on due to the affect of heat

produced by the light from the light source.

It is recommended that the focus be adjusted after the image has been projected for

approximately 1 hour.

■Adjusting the focus

Peripheral focus adjustment ring

ENGLISH-7

Preparation (continued)

Lens calibration

Perform lens calibration after attaching the lens.

1) Press the <MENU> button.

2) Use the ▲ and ▼ buttons to

select [PROJECTOR SETUP],

and press the <ENTER>

button.

zThe [PROJECTOR SETUP] screen

appears.

3) Use the ▲ and ▼ buttons to

select [LENS], and press the

<ENTER> button.

zThe [LENS] screen appears.

4) Use the ▲ and ▼ buttons to

select [LENS CALIBRATION],

and press the <ENTER>

button.

zThe [LENS CALIBRATION] screen

appears.

5) Use the ▲ and ▼ buttons to

select [SHIFT/FOCUS/ZOOM],

and press the <ENTER>

button.

zThe confirmation screen appears.

6) Use the and buttons to

select [OK], and press the

<ENTER> button.

zLens calibration starts.

zThe projection lens moves to the

home position after adjustment

range calibration is complete.

1/2

PROJECTOR SETUP

PROJECTOR ID ALL

PROJECTION METHOD

LENS

OPERATION SETTING NORMAL

LIGHT OUTPUT 100.0%

BRIGHTNESS CONTROL AUTO

NO SIGNAL SETTING

LAST MEMORY

LAST USED

INITIAL STARTUP

STARTUP INPUT SELECT

OFF

DATE AND TIME

SCHEDULE

MULTI PROJECTOR SYNC

MENU SELECT

ENTER

SUB MENU

MENU SELECT

ENTER

LENS

LENS INFORMATION SETTING

LENS MEMORY

LENS HOME POSITION

ACTIVE FOCUS OPTIMIZER

LENS CALIBRATION

EXECUTE

MENU SELECT

ENTER

LENS CALIBRATION : ET-D3QW200

SHIFT/FOCUS/ZOOM

SHIFT/FOCUS

ZOOM

LENS CALIBRATION : ET-D3QW200

Proceed LENS CALIBRATION,

and return to HOME POSITION.

EXECUTE

CHANGE

ENTER

CANCEL

Note

zIf lens calibration is not performed, the available zoom range will be narrowed.

8-ENGLISH

Projection relationships

The dimensional relationship between the screen and the projector is shown below.

■Dimensional relationship diagram

L (LW/LT)

L2 L (LW/LT)

Screen

Projected image

Note

zThis diagram assumes that the size and position of the projected image will be adjusted so

that the image fills the entire screen.

zThis illustration is not drawn to scale.

L Projection distance

LW Minimum distance

LT Maximum distance

L1 Lens protrusion dimension (distance from the front surface of the

projector to the forward end of the projection lens)

L2 Position of the lens optical axis (distance from the front surface of the

projector to the lens optical axis)

L3 Position of the lens apex (distance from the side of the projector to the

lens apex)

SH Projected image height

SW Projected image width

SD Projected image size

zDimensions for L1, L2, and L3 (approximate values) (Unit: m)

Projector model L1 L2 L3

PT-RQ50K 0.31 0.24 0.17

ENGLISH-9

Projection relationships (continued)

Note

zThe illustrations of projectors in this manual are for informational purposes only and do not

represent a specific projector model. Configurations may vary with the model.

zIf the screen is tilted downward, extend the adjustable feet on the sides of the projector

until the projected image is rectangular.

If the projector is inclined horizontally, adjust the adjustable feet until the projector is level.

You can extend the adjustable feet by turning them as shown in the diagram. To return the

feet to the original position, turn them in the opposite direction.

Attention

zTo prevent obstruction of the intake and exhaust vents, install the projector with a

clearance at least 500 mm (1 ft. 7 in.) from walls and objects.

If you are installing the projector in a sealed space, be sure to provide additional air

conditioning equipment and ventilation equipment. Insufficient ventilation will result in an

accumulation of heat and may activate the projector's protection circuit.

zAvoid setting up in places which are subject to sudden temperature changes, such as near

an air conditioner or lighting equipment (studio lamps, etc.).

■Dimensional relationship

For details on the projection distance (L), refer to “Projected image size and Projection

distance” and “Projection distance formulas” in the Appendix.

10-ENGLISH

Projection relationships (continued)

■[GEOMETRY] projection range

[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)

Screen Screen

Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)

Screen

L2: Projection

distance

R2: Arc radius

Screen

L2: Projection

distance

R2: Arc radius

R3L3

Screen

L3: Projection

distance

R3: Arc radius

Arc center

R3L3

Screen

L3: Projection

distance

R3: Arc radius

Arc center

Projector

model

Only [KEYSTONE]

used

[KEYSTONE] and [CURVED CORRECTION]

used together

Only [CURVED

CORRECTION] used

Vertical

keystone

correction

angle α (°)

Horizontal

keystone

correction

angle β (°)

Vertical

keystone

correction

angle α (°)

Horizontal

keystone

correction

angle β (°)

Min. value

of R2/L2

Min. value

of R3/L3

Min. value

of R2/L2

Min. value

of R3/L3

PT-RQ50K ±15 ±5 - - - - - -

Tabla de contenidos

Otros manuales de Accesorios para proyectores de Panasonic

Panasonic

Panasonic ET-ELW21 Manual de usuario

Panasonic

Panasonic ET-LAD10000 Manual de usuario

Panasonic

Panasonic ET-DLE170 Manual de usuario

Panasonic

Panasonic ET-LAEF100 Manual de usuario

Panasonic

Panasonic ET-LAV100 Manual de usuario

Panasonic

Panasonic ET-LEC701 Guía

Panasonic

Panasonic Panaboard KX-BP535 Manual de usuario

Panasonic

Panasonic ET-RFL100 Manual de usuario

Panasonic

Panasonic ET-LAL500 Manual de usuario

Panasonic

Panasonic ET-PKD130B Manual de usuario

Panasonic

Panasonic ET-LAD510 Manual de usuario

Panasonic

Panasonic ET-D75LE8 Manual del sistema

Panasonic

Panasonic ET-LAD7700 Guía

Panasonic

Panasonic ET-LAA110 Manual de usuario

Panasonic

Panasonic ET-ELW20 Manual de usuario

Panasonic

Panasonic ET-PAD310 Manual de usuario

Panasonic

Panasonic ET-LAD60A Manual de usuario

Panasonic

Panasonic ET-LAD57 Guía

Panasonic

Panasonic ET-LAC100 Manual de usuario

Panasonic

Panasonic ET-EMF320 Manual de usuario

Panasonic

Panasonic ET-DLE020 Manual de usuario

Panasonic

Panasonic ET-LAB50 Guía

Panasonic

Panasonic ET-LAD310A Manual de usuario

Panasonic

Panasonic ET-EMW200 Manual de usuario

Manuales populares de Accesorios para proyectores de otras marcas

Optoma

Optoma BX-AL133B Manual de usuario

PEERLESS

PEERLESS PE 1120 Guía

Osram

Osram SIRIUS HRI Series Manual

Presentation Switchers

Presentation Switchers PS111 Manual de usuario

Kramer

Kramer VIA GO Manual de usuario

Yamaha

Yamaha PJL-112 Manual de lista de piezas

Swedstyle

Swedstyle CL23AA02ZA25E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 236CB Manual del propietario

Epson

Epson BrightLink 475Wi Manual de usuario

Acer

Acer WP100 Manual de usuario

i3 i3board Manual de usuario

CHIEF

CHIEF HB-43E Manual de usuario

Biamp

Biamp Modena Hub Manual de servicio

NEC

NEC MP10RX Manual de usuario

Panamorph

Panamorph DCR-S3 Manual de usuario

Exact solutions

Exact solutions FRAME-EVO-P10 Manual de usuario

CHIEF

CHIEF VCM103S Manual de usuario

InFocus

InFocus LP70+ Guía