Panasonic CF-VDW07HM Manual de usuario

Panasonic Wireless Display Monitor – CF-VDW07HM

Installation & Configuration

General

The Panasonic Wireless Display Monitor (WDM) can be installed either in Ad-Hoc mode or

Infrastructure mode. In Ad-Hoc mode, the WDM communicates directly with the PC it is

controlling via the wireless card in the PC. In Infrastructure mode, the WDM communicates

through a Wireless Access Point (or Wireless Router) to the PC it is controlling. In

Infrastructure mode, the PC that is being controlled does not need to have a wireless card. Since

this is the typical configuration for use with Scrap Dragon, that is the method that is described

herein. Each WDM can be configured with 4 different profiles, allowing a single WDM to

control up to 4 different computers on the network.

Installing the Software on the PC

1. On the computer that will be controlled by the Wireless Display Monitor (WDM).

2. Install the MeiWDS software from the installation CD. Run setup.exe from the \meiwds

folder.

3. Reboot the computer. The Wireless Display Setup Utility icon will appear in the

system tray. This is a Windows service, WDS Server.

4. Install the software keyboard from the installation CD. Run setup.exe from the \softkb

folder.

Infrastructure Setup

It is necessary to set the parameters of the Access Point and the PC to the WDM defaults to

establish the initial connection. Once the WDM is connected to the PC, the Wireless Display

Setup Utility is used to change the parameters to the ones that are appropriate for your network.

Isolate the PC and the Access Point from the

rest of the network. Turn on the WDM. If

the WDM has never been connected, you

will see this screen:

If you don’t see this screen, it is because the

WDM has previously been connected.

Follow the instructions on the next page to

get to this screen.

Skip this page if you see this screen:

Press the MENU button on the WDM, you

will see this screen:

Select [Option] using the stylus, you will see

this screen:

Select [Setup] using the stylus, you will see

this screen:

Choose the Profile you wish to configure,

you will see this screen:

Select Infrastructure, you will see this screen

with the information needed to make the

initial connection using the built in default

values. The IP Address of the PC and the IP

Address, SSID and Encryption of the Access

Point MUST match the values displayed

here. While you can use Class A, Class B or

Class C, these instructions assume you are

using Class C.

Select Class C. The default IP Address will be something like 192.168.19.49, and the subnet

mask will be 255.255.255.0. Follow these steps:

1. Determine the current IP address of the Access Point and the user name and password to

user manual for the specific values.

2. In Internet Explorer enter the IP address of the Access Point and login to the

configuration page. Note that the IP address scheme of the PC must match the IP address

scheme of the Access Point or it will not be accessible. You may have to temporarily

change the IP address of the PC.

3. Set the SSID of the Access Point to cfvdw07 and disable encryption. Save the changes.

4. Change the IP address of the Access Point to an address that is the same scheme as the

default address for the PC that is indicated in the WDM. For example, if the default

address is 192.168.19.49, then set the Access Point address to 192.168.19.1. Do not use

an IP address that is just one larger than the default as this is assigned to the WDM. Save

the changes.

5. Change the IP address and subnet mask of the LAN card in the PC to match the default

address for the PC that is indicated in the WDM. For example, 192.168.19.49.

6. It is NOT necessary to create a wireless network profile as indicated in the Panasonic

instruction manual.

7. Left click on the MeiWDS icon in the system tray, then click Password. Enter the

default password wdsp and then OK.

8. Disable any Windows firewall software that might prevent connectivity, or create a port

exception for TCP 11900.

9. On the WDM, select [Connect] with the stylus. If the connection is successful, the screen

on the handheld will mirror the PC, and the MeiWDS icon in the system tray will change

from to .

At this point, the WDM should be communicating with the PC and the screens should be

mirrored. This will also enable access to the Wireless Display Setup Utility that allows the

WDM to be reconfigured to the actual parameters that you wish to use on your network.

Left click on the MeiWDS icon in the system tray and then click Run Setup Utility. Or run

the Wireless Display Setup Utility from the start menu.

Wireless Display Setup Utility

The Wireless Display Setup Utility can only

be run when the WDM is connected to the

PC. The first screen of the Wireless Display

Setup Utility looks like this:

Make sure you are on the correct profile.

You can change the SSID, the encryption,

the IP Addresses and the subnet mask. You

can also give the profile a meaningful name.

When you click the Next button, the new

settings will be saved in the WDM and you

will be prompted to make the corresponding

changes in the Access Point and in the PC.

When changing IP Addresses, always

change the Access Point first, or you will

not be able to connect to it from your

browser.

If necessary, you can repeat this process for other PC’s, using a different profile for each.

You can now reconnect the Access point and the PC to the rest of the network. The WDM

should connect to the PC whenever the WDM is turned on and this profile selected.

Tabla de contenidos

Otros manuales de Monitor de Panasonic

Panasonic

Panasonic TH-103PF10UK - 103" Plasma Panel Manual de usuario

Panasonic

Panasonic TH-58PF20U TENTATIVE Manual de usuario

Panasonic

Panasonic TH-42PM50U Manual de usuario

Panasonic

Panasonic PT53X54J - 53" PROJECTION TV HD Manual de usuario

Panasonic

Panasonic BT-M2090Y Manual de usuario

Panasonic

Panasonic ATH1915DA - BROADCAST MONITOR Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Panasonic

Panasonic TH-42PF11RK Manual de usuario

Panasonic

Panasonic TH-42PHW6EX Manual de usuario

Panasonic

Panasonic TH-42PF20 Manual de usuario

Panasonic

Panasonic BT-LH1710 - Professional - LCD Production... Manual de usuario

Panasonic

Panasonic TH-49SF1HU Manual de usuario

Panasonic

Panasonic TH-42LF5U Manual de usuario

Panasonic

Panasonic 65PF9UK - TH - 65" Plasma Panel Manual de usuario

Panasonic

Panasonic CY-VMC7000U Manual de usuario

Panasonic

Panasonic TH-55AF1U Manual de usuario

Panasonic

Panasonic TH-50PH30ER Manual de usuario

Panasonic

Panasonic PT-50LC13K Manual de usuario

Panasonic

Panasonic BT-H1700P Manual de usuario

Panasonic

Panasonic TH37PR10U - 37" PLASMA TELEVISION Manual de usuario

Panasonic

Panasonic TY-SP65P7W-K Manual de usuario

Panasonic

Panasonic PT53X54J - 53" PROJECTION TV HD Manual de usuario

Panasonic

Panasonic TH-37PHD8GK Manual de usuario

Panasonic

Panasonic TH-42PRT12U Guía de configuración

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación

LG M1950D-PZ Manual de usuario