Panasonic NN-C784MF Manual de usuario
ORDERNO.SIMMC0408027A3
Microwave Oven
NN-C784MF / NN-C784WF
HPE(Hong Kong)
YPQ(Singapore)
MPQ(Malaysia)
TPE(Thailand, Indonesia)
YTE(Others)
KTE(UAE)
KUE(Egypt)
PTE( Iran)
KPQ(Kuwait, Doha, Qatar, Oman, Bahrain, Pakistan)
STM(Saudi Arabia)
ZPE(CISCountries)
SPECIFICATIONS
1
2004 PanasonicHome Appliances Microwave Oven (Shanghai)
Co., Ltd. / All rights reserved. Unauthorized copying and
distribution isaviolation of law.
2
3
4
5
1. SCHEMATIC DIAGRAM
1.1. NN-C784MF/WF (EXCEPT ZPE)
1.2. NN-C784MF (ZPE)
6
2. CAUTIONS TO BE OBSERVED WHEN
TROUBLESHOOTING
Unlike manyotherappliances, the microwave ovenis a high voltage, high current device. It is
free fromdangerinordinaryuse, though extreme care shouldbe takenduring repair.
Caution
Servicemen shouldremove theirwatches whenever working close
to or replacing the magnetron.
2.1. Check the grounding
7
Donot operate on a twowire extension cord. The microwave ovenis designedtobe grounded
whenused. It is imperative, therefore, toensure the appliance is properlygroundedbefore
beginning repairwork.
2.2. Inverter warnings
DANGER, HIGH VOLTAGE AND HIGH TEMPERATURE (HOT/LINE) OFTHE INVERTER POWER
SUPPLY (U)
Thishigh voltage inverter power supplyhandles veryhigh voltage
and current for the magnetron tube. Though itisfree from danger
inordinaryuse, extreme care shouldbe taken during repair.
The aluminum heat sink isalso energized with high voltage (HOT),
so do not touch when the AC input terminalsare energized. The
power devices Collector isdirectlyconnected to the aluminum heat
sink.
The aluminum heat sink maybe HOTdue to heat energy, therefore,
extreme care shouldbe taken during servicing.
H.V. Inverterwarning
WARNING FOR INVERTER POWER SUPPLY (U) GROUNDING
Check the high voltage inverter power supplycircuitgrounding.
The high voltage inverter power supplycircuitboard must have a
proper chassisground, the inverter grounding bracket must be
connected to the chassis. Ifthe inverter board isnot grounded it
will expose the user to veryhigh voltages and cause extreme
DANGER!Besure that the inverter circuitisproperlygrounded via
the inverter earth bracket.
8
Grounding of the invertercircuit board
WARNING!DISCHARGE THE HIGH VOLATGE CAPACITORS
For about 30 seconds after the oven isturned off, an electriccharge
remains inthe high voltage capacitors inthe inverter power supply
circuitboard.
When replacing or checking parts, remove the power plug from the
outlet and short the inverter output terminal of the magnetron
filament terminalsto the chassisground with an insulated handle
screwdriver to discharge. Please be sure to touch the chassis
ground side first and then short to the output terminals.
Discharging the high voltage capacitors
WARNING
There ishigh voltage present with high current capabilities inthe
circuits of the primaryand secondarywindings, choke coil and heat
sink of the inverter. Itisextremelydangerous to work on or near
these circuits with the oven energized. DO NOTmeasure the
voltage inthe high voltage circuitincluding the filament voltage of
the magnetron.
9
WARNING
Never touch anycircuitwiring with your hand or with an insulated
tool during operation.
2.3. Part replacement.
Whenanypart orcomponent is tobe replaced, always ensure that the powercordis removed
fromthe wall outlet.
2.4. When the 10Afuse isblowndue to the operation of the short
switch:
WARNING
When the 10A250V fuse isblowndue to the operation of the
interlock monitor switch, replace all of the components (primary
latch switch, secondarylatch switch, short switch and power relay
B(RY1)).
1. Thisismandatory. Refer to “adjustments and measurements” for
the location of these switches.
2. When replacing the fuse, confirm that ithas the appropriate rating
for these models.
3. When replacing faultyswitches, be sure the mounting tabs are
not bent, broken or deficient intheirabilityto holdthe switches.
2.5. Avoidinserting nails, wire etc. through anyholes inthe unit
during operation.
Neverinsert a wire, nail oranyothermetal object through the lampholes on the cavityorany
holes orgaps, because suchobjects maywork as anantenna and cause microwave leakage.
2.6. Confirm after repair
1. After repairor replacement of parts, make sure that the screwsof
the oven, etc. are neither loose nor missing. Microwaves might
leak ifscrewsare not properlytightened.
2. Make sure that all electrical connections are tight before inserting
the plug into the wall outlet.
3. Check for microwave energyleakage. (Refer to procedure for
measuring microwave energyleakage).
CAUTION MICROWAVE RADIATION
USE CAUTIONNOTTO BECOME EXPOSEDTO RADIATIONFROM
THEMICROWAVE MAGNETRONOROTHERPARTS CONDUCTING
10
Otros manuales para NN-C784MF
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Microondas de Panasonic
Panasonic
Panasonic NN-SD377S Manual de instrucciones
Panasonic
Panasonic NN-SD291W Manual de usuario
Panasonic
Panasonic NN-GF574S Manual de usuario
Panasonic
Panasonic NN-ST651B Manual de usuario
Panasonic
Panasonic NN-S788BA Manual de usuario
Panasonic
Panasonic NN-CD989S Manual de usuario
Panasonic
Panasonic NN-SM221W Manual de usuario
Panasonic
Panasonic NN-ST27HMZPE Manual de usuario
Panasonic
Panasonic INVERTER NN-GT46KB Manual de usuario
Panasonic
Panasonic NN-A750WB Manual de usuario
Panasonic
Panasonic Inverter NN-T685S Manual de usuario
Panasonic
Panasonic NNF693 Manual de usuario
Panasonic
Panasonic NN-MX20 Manual de usuario
Panasonic
Panasonic NN-GD368M Manual de usuario
Panasonic
Panasonic The Genius NN-S780BA Manual de usuario
Panasonic
Panasonic NN-SD376S Manual de usuario
Panasonic
Panasonic NN-GD462M Manual de usuario
Panasonic
Panasonic NE-671 Manual de usuario
Panasonic
Panasonic NE1064T - COMMERCIAL MICROWAVE Manual de usuario
Panasonic
Panasonic NN-SD698S Manual de usuario
