Panasonic WJSX150 - SWITCHER - ADDENDUM Instrucciones de instalación y funcionamiento

This operation is skipped when the auto login is set to ON.

(Refer to the operating instructions of matrix switcher.)

1. Turn on the power switches of all system components.

The OPERATE indicator will light up.

2. To turn on the power of the system controller, connect

the AC adapter to the AC outlet.

The OPERATE indicator lights up and "Terminal Mode

No User" appears on the LCD.

BEFORE OPERATION

INSTALLATIONS AND CONNECTIONS

SETUP PROCEDURES (HARDWARE)

Note: This section describes the terminal mode. To operate

in the PS·Data mode, refer to the operating instructions.

Before starting the following procedures, all system compo-

nents must be turned on.

The following procedures are applicable when the system

controller is connected to the matrix switcher.

■ Operation Start (Login)

Note: When auto login is set to ON, operators can log into

the system without entering their passwords. (Refer to

p. 2 Operation Start (Auto Login).)

Terminal Mode

No User

Addendum for WV-CU950/650 and WJ-SX150 Series

(1) ADDENDUM FOR SYSTEM CONTROLLER WV-CU950/WV-CU650:

MATRIX SWITCHER WJ-SX150 SERIES

OPERATING PROCEDURES

The descriptions in this document are applicable when WJ-SX150A Administrator Console and the firmware of this unit (matrix

switcher) are Ver. 2.04 or later.

Note: Refer to the operating instructions of matrix switcher for how to check the version.

■Basic System Connections

•The connection details are the same as System

Controller WV-CU360C/CJ. Refer to the operating

instructions of matrix switcher .

•

To connect System Controller WV-CU950 or WV-CU650

to Digital Disk Recorder WJ-HD300 Series or WJ-HD220

Series via the matrix switcher, refer to pp. 37 to 40.

■MODE Switch Setting

Either of the terminal mode or PS·Data mode are applicable

for connections. Refer to WV-CU950/WV-CU650 Operating

Instructions for details on the switch setting for each mode.

■CONTROLLER NO. Switch

Setting

Normally, set this switch to “1” (default position).

■ Operation End (Logout)

This operation is skipped when the auto logout is set to ON.

This function is used when an operator leaves the controller

or no longer requires access to the system.

To log out of the system, press the MON LOCK/LOGOUT

button while holding down the SHIFT button.

"Logout" will blink on the LCD for about 3 seconds. Then,

"Terminal Mode No User" appears on the LCD.

Note: If you want to save the power consumption, discon-

nect the DC 9 V plug from the controller, and remove

the AC adapter from the AC outlet.

■ Operation End (Auto Logout)

If the auto logout is set to ON and no operation takes place

for a specific time, any operators can logout automatically.

After the logout, "Terminal Mode No User" automatically

appears on the LCD.

You can activate auto logout and set up the duration until

logout (configurable by minute) through WJ-SX150A

Administrator Console. (Refer to the operating instructions

of matrix switcher.)

3. To select your registered operator ID number (1 to 16,

up to 2 digits), press the numeric buttons, then press

the CAM (SET) button.

"Password" entry form appears on the LCD.

Note: The factory default setting is 150.

4. To select your registered password (up to 5 digits),

press the numeric buttons, then press the CAM (SET)

button.

The factory default setting is "150".

If the operator ID and password are correct, "Login OK"

will blink on the LCD for about 3 seconds. Then, "Mon -"

"Cam - -" will appear on the LED display.

Note: If an operator ID or password error occurs,

"Invalid" will blink on the LCD for about 3 seconds.

Then, return to Step 3 and select your operator ID.

■ Operation Start (Auto Login)

If the auto login is set to ON, any operators can log into the

system automatically. After the controller is turned on, "Auto

then "Mon -" "Cam - -" automatically appears.

Auto login is configurable through WJ-SX150A

Administrator Console. (Refer to the operating instructions

of matrix switcher.)

Mon- Cam--

User ID 150

Password __∗∗∗

Mon- Cam--

Invalid

Blinking

Terminal Mode

No User

Terminal Mode

No User

User ID 150

Password _____

● Releasing Priority Lock

1. Select the desired monitor. (Refer to Monitor Selection.)

2. Press the MON LOCK/LOGOUT button to release the

priority lock mode.

The monitor number returns to the normal display on

the active monitor.

■ Camera Selection

1. Select the desired monitor. (Refer to Monitor Selection.)

2. Press the numeric buttons to select the desired camera

number (1 to 99).

3. Press the CAM (SET) button.

The selected camera's image will appear on the active

monitor, and the selected camera number will appear

on the LCD.

Note: If you have entered a wrong camera number,

press the CLEAR button to clear the input.

4. If the selected camera number is not valid, "Prohibited"

and the camera number will blink on the LCD for about

3 seconds.

In this case, return to Step 2 and select another camera

number.

Note: If the camera is selected by an operator with

higher priority, "Prohibited" will also blink on the

LCD.

5. To replace the currently selected camera with the next

higher-numbered camera , press the + button.

To replace the currently selected camera with the next

lower-numbered camera, press the – button.

Note: Cameras selected by operators with higher priori-

ty will be skipped.

Note: This section describes the terminal mode. To operate

in the PS·Data mode, refer to the operating instructions.

After the login procedure, the following operations are avail-

able to control the system.

The operation begins with monitor selection. Then, the

image of selected camera appears on the active monitor.

■ Monitor Selection

1. To select the desired monitor number (1 to 4), press the

numeric button.

2. Press the MON (ESC) button to execute the selection.

The selected monitor number will appear on the LCD.

3. If the selected monitor number is not valid, or if an oper-

ator with higher priority is controlling the monitor, the

monitor number and "Prohibited" will blink on the LCD

for approximately 3 seconds.

In this case, return to Step 1 and select another monitor

number.

■ Priority Lock

● Applying Priority Lock

1. Select the desired monitor. (Refer to Monitor Selection).

2. Press the MON LOCK/LOGOUT button to toggle the pri-

ority lock mode on and off on the active monitor.

If the priority lock mode is selected, the monitor number

will inversely appear on the active monitor as shown in

the figure.

Note: This function will prevent operators with lower priority

from gaining control of a monitor.

However, higher or equal priority operators may still

gain control of the monitor.

Mon1 Cam--

MONITOR SELECTION AND CAMERA SELECTION

Mon1 Cam03

Mon1 Cam04

Mon- Cam--

Prohibited

Blinking

M04

Note: This section describes the terminal mode. To operate

in the PS·Data mode, refer to the operating instructions.

Buttons and control for cameras or camera site accessories

are located on the 3D joystick unit and the right side of

main unit.

Included are zoom control, focus control, iris control, preset

and pan/tilt controls.

Normally, combination cameras equipped with the specific

feature or a WV-RC100 or WV-RC150 Receiver are required

to utilize these functions.

Note: Refer to the cameras' operating instructions whether

to confirm that each function is available.

■ Lens Control

This function is available when specified lens, with motor-

ized zoom/focus functions, is mounted on the camera, and

the lens selection (DC/VIDEO) on the camera is set to DC.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the FOCUS FAR or NEAR button while watching

the monitor. The lens focus is adjusted to obtain a

sharply focused image.

Note: Pressing the B button or top button of 3D joystick

unit can also set the lens focus automatically.

3. To adjust the lens zoom, move the zoom wheel con-

troller to the right (TELE) or left (WIDE).

4. Press the IRIS OPEN or CLOSE buttons to open/close

the lens iris. The lens iris is adjusted by these buttons to

obtain the proper image exposure.

Note: To set the lens iris automatically, press the A but-

ton of 3D joystick unit.

■ Pan/Tilt Control

● Manual Operation

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Move the 3D joystick to move the pan/tilt head towards

the desired direction.

● Auto Panning

Refer to p. 8 Camera Panning Function for how to oper-

ate.

CAMERA CONTROL

FAR

FOCUS

NEAR

OPEN

IRIS

Top button

WIDE TELE

Zoom wheel controller

■ Program Preset Position

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. To move the camera to the position to be preset, move

the 3D joystick and press the lens control buttons.

3. To select the desired preset position number, press the

numeric buttons. (1 to 64)

4. When you have selected a wrong number, press the

CLEAR button to clear the numeric input.

5. Press the PRESET/PGM PRESET button while holding

down the SHIFT button to save a preset position of the

selected camera.

Notes:

•If the entered position number has stored the previ-

ous preset position, it will be overwritten by the new

one.

•SETUP MENU and WJ-SX150A Administrator

Console can configure each operator's pan/tilt con-

trol. (Refer to the operating instructions of matrix

switcher.)

■ Call Preset Position

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. To select the desired preset position number, press the

numeric buttons. (1 to 64)

3. When you have selected a wrong number, press the

CLEAR button to clear the numeric input.

4. Press the PRESET/PGM PRESET button to move to the

preset position of the selected camera on the active

monitor.

Notes:

•To use the above function, you must set the preset

position number for the camera.

•If you press no numeric buttons or the button 0 in

Step 2, the camera will move to the home position.

Mon1 Cam03 Pre48

Memory

Mon1 Cam03 Pre05

■ Camera Function (Shortcut

Function)

The following function is available only when specified cam-

eras with the camera function feature are used.

This function enables executing camera functions via a

shortcut.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the numeric buttons to select an assigned func-

tion number, then press the CAM FUNC/SYS FUNC but-

ton.

For example, enter 175 for AGC ON.

The selected function will be executed on the active

monitor.

Notes:

•When you select a wrong number, press the CLEAR

button to clear the numeric input.

•Refer to the cameras' operating instructions for

details on available shortcuts.

Note: This section describes the terminal mode. To operate

in the PS·Data mode, refer to the operating instructions.

■Camera Setup

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the MENU button repeatedly until "Camera Setup"

appears on the LCD.

3. Press the F1 button. The camera's SETUP MENU will

appear on the active monitor.

4. To select the desired item in the menu, move the 3D

joystick to Cor D. To select the desired parameter (or

mode) in the menu, move the 3D joystick to Aor B.

5. To execute the currently highlighted selection and to

enter a submenu of SETUP MENU, press the CAM

(SET) button.

6. To leave from the currently selected menu and to return

to the previous page of the menu, press the MON (ESC)

button.

7. Move the cursor to SPECIAL on the camera’s setup

menu, and press the F3 button to display the special

menu.

8. Move the cursor to CAMERA RESET on the camera’s

setup menu, and press the F4 button to reset all the

functions to the defaults.

Note: Refer to the operating instructions of the selected

camera for details.

9. To close the camera's SETUP MENU, press the F2 but-

ton.

10. To exit the mode, press the MON (ESC) button.

CAMERA FUNCTION CONTROL

Camera Setup 006

On Off Rst A.Rst

Camera Setup 006

On Off Rst A.Rst

■ Patrol Learn and Play

A routine of manual operations can be stored for a specific

time and later reproduced repetitively.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. To save the patrol sequence, follow the procedure

below.

qPress the MENU button repeatedly until "Patrol

Learn" will appear on the LCD.

wPress the F1 button.

eOperate the camera manually.

rPress the F2 button.

The operation data will be saved.

3. To reproduce the operation data, follow the procedure

below.

qPress the MENU button repeatedly until "Auto

Mode" appears on the LCD.

wPress the F4 button.

eTo stop the reproduction, move the 3D joystick.

4. To exit the mode, press the MON (ESC) button.

Patrol Learn 007

Start Stop

Auto Mode 009

Seq Sort Pan Patrol

■Auto Pan Setup and Activation

You will set up and activate the auto pan function. The cam-

era can pan between the start and end points you will set.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the MENU button repeatedly until "Auto Pan

Setup" appears on the LCD.

3. To set the start and end point of auto pan, perform the

following.

qTo move the camera to a point you wish to start

auto pan, move the 3D joystick and press the lens

control buttons (IRIS OPEN and CLOSE, FOCUS

FAR and NEAR).

wPress the F3 button.

The start point of auto pan will be set.

eTo move the camera to a point you wish to end auto

pan, move the 3D joystick.

rPress the F4 button.

The end point of auto pan will be set.

Auto Pan Setup 008

Play Rvrs Start End

■ Changing to Black and White

Images

This function gets the clear camera images on the monitor

while shooting the objects under low light conditions.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the MENU button repeatedly until "BW Mode"

appears on the LCD.

3. Press the F1 button to change the image from the color

mode to the BW (black and white) mode on the active

monitor.

4. Press the F2 button to change the BW image to the

color image on the active monitor.

5. Press the MON (ESC) button to exit the mode.

■ Camera Panning Function

There are three panning modes available as follows:

sequence mode, sort mode, and auto pan. (Refer to the

operating instructions of matrix switcher.)

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the MENU button repeatedly until "Auto Mode"

appears on the LCD.

3. Press the assigned function button to activate the pan-

ning function of the selected camera.

The LCD will indicate the selected mode as follows.

F1: "Seq" (Activates SEQUENCE PAN.)

F2: "Sort" (Activates SORT PAN.)

F3: "Pan" (Activates AUTO PAN.)

Note: The AUTO MODE parameter, previously set in

the camera's SETUP MENU, will be automatically

replaced to the activated function parameter.

4. To exit the mode, press the MON (ESC) button.

BW Mode 010

On Off Auto1 Auto2

Auto Mode 009

Seq Sort Pan Patrol

Note: This section describes the terminal mode. To operate

in the PS·Data mode, refer to the operating instructions.

■Receiver Control

The following functions are available only when the

receivers are included in the system and the specified

camera housing is installed.

● Camera Housing Control

Wiper Control

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the WIPER button to turn on the housing wiper of

the camera repeatedly until buttons are released.

Defroster Control

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the DEF ON/OFF button to turn on the housing

defroster of the camera.

3. To turn off the defroster, press the DEF ON/OFF button

while holding down the SHIFT button.

● Auxiliary Control

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the AUX1 ON/OFF button to turn on the user's

auxiliary switch 1 of the receiver.

Press the AUX1 ON/OFF button while holding down the

SHIFT button to turn off the user's auxiliary switch 1 of

the receiver.

3. Press the AUX2 ON/OFF button to turn on the user's

auxiliary switch 2 of the receiver.

Press the AUX2 ON/OFF button while holding down the

SHIFT button to turn off the user's auxiliary switch 2 of

the receiver.

CAMERA SITE ACCESSORIES CONTROL

Note: This section describes the terminal mode. To operate

in the PS·Data mode, refer to the operating instructions.

■ Tour Sequence

The following functions are available if a tour sequence has

been previously configured through SETUP MENU or WJ-

SX150A Administrator Console. Any tour sequence can be

assigned to any monitors.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. To select the desired tour sequence number, press the

numeric buttons.

3. When you have selected a wrong number, press the

CLEAR button to clear the numeric input.

4. Press the TOUR SEQ/GROUP SEQ button to run the

tour sequence in the forward direction on the active

monitor.

5. Press the SEQ PAUSE/SEQ STOP button to pause a

tour sequence on the active monitor.

The "P" sign (indicating the pause status) is displayed

at the tour sequence number on the active monitor, and

a camera number currently selected appears on the

LCD.

•Press the SEQ PAUSE/SEQ STOP button to restart a

tour sequence forward from the next step that was pre-

viously paused.

•Press the + button to move the sequence one frame to

the next step from the step that was previously paused.

•Press the – button to move the sequence one frame to

the previous step from the step that was previously

paused.

6. Press the SEQ PAUSE/SEQ STOP button while holding

down the SHIFT button to stop a tour sequence on the

active monitor and return to spot monitoring.

■ Group Sequence

The following function is available only if a group sequence

has been previously established in WJ-SX150A

Administrator Console.

A group sequence determines the assignment of monitors

and cameras. Therefore, monitor selection is not required.

1. Press the numeric buttons to select a desired group

sequence number.

2. When you have selected a wrong number, press the

CLEAR button to clear the numeric input.

3. Press the TOUR SEQ/GROUP SEQ button while holding

down the SHIFT button to run a group sequence for-

ward on the assigned monitors.

4. Press the SEQ PAUSE/SEQ STOP, + or – button to

operate the group sequence. Refer to Step 5 of Tour

Sequence in this page for how to use these buttons.

5. To stop the sequence, select one of the monitors that

are being run on the selected group sequence, then

press the SEQ PAUSE/SEQ STOP button while holding

down the SHIFT button

Note: If an alarm is activated during a sequence pause, the

sequence runs again after the matrix switcher recovers

from the alarm mode.

RUNNING SEQUENCE

Mon1 Cam01

T04

Mon1 Cam07

T04P

Mon1 Cam01

T01

Otros manuales para WJSX150 - SWITCHER - ADDENDUM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Conmutador de matriz de Panasonic

Panasonic

Panasonic WJSX550A - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX550B - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic Matrix System150 WJ-SX155 Manual de usuario

Panasonic

Panasonic AVHS400N - MULTI FORMAT LIVE SWITCHER Manual de usuario

Panasonic

Panasonic WJSX550B - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX550C - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX150 - SWITCHER - ADDENDUM Manual de usuario

Panasonic

Panasonic WJ-SX 150A Manual de usuario

Panasonic

Panasonic WJSX650 - SWITCHER Manual de usuario

Panasonic

Panasonic WJSX350 - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX350 - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX550C - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJ-SX650/G Manual de usuario

Panasonic

Panasonic WJSX150 - SWITCHER - ADDENDUM Manual de usuario

Panasonic

Panasonic WJSX550A - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX350 - MATRIX SWITCHER Manual de usuario

Panasonic

Panasonic WJSX650 - SWITCHER Manual de usuario

Panasonic

Panasonic System 850 Manual de usuario

Panasonic

Panasonic WJSX550A - MATRIX SWITCHER Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas