Panasonic EBL512 G3 5000 Manual técnico

Planning Instructions

MEW01472

Revision -

Fire Alarm System EBL512 G3

United version 2.7.x

Author: Jan Pettersson

Date of issue: 2012-04-05

Date of rev:

This page has deliberately been left blank.

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

Table of contents

1Introduction________________________________ 9

2Definitions / Explanations ___________________ 11

2.1 PEWN AB_______________________________________ 11

2.2 Alarm points _____________________________________ 11

2.2.1 Smoke detector _______________________________ 11

2.2.2 Sensor ______________________________________ 11

2.2.3 Analog detector_______________________________ 11

2.2.4 Analog (Sensor) Base (ASB) ____________________ 11

2.2.5 Conventional detector __________________________ 11

2.2.6 (Conventional Detector) Base (CDB) ______________ 11

2.2.7 Addressable__________________________________ 11

2.2.8 Conventional zone line input / External line_________ 12

2.3 Output unit ______________________________________ 12

2.4 Output / Control output_____________________________ 12

2.5 Short circuit isolator (ISO) __________________________ 12

2.6 Display unit (D.U.) ________________________________ 12

2.7 COM loop _______________________________________ 12

2.8 Control Unit / C.U. / C.I.E.__________________________ 12

2.9 Fire Brigade Panel (FBP) ___________________________ 12

2.10 Control panel (CP) ________________________________ 12

2.11 System__________________________________________ 12

2.12 Network / TLON®/ LonWorks®/ Echelon / Node / TLON

Conn. board / Channel / Backbone net / Router / Repeater _______ 13

2.13 LED____________________________________________ 13

2.14 External Indicator (Ext. LED)________________________ 13

2.15 Display / LCD____________________________________ 13

2.16 Door open (Door / Key switch)_______________________ 13

2.17 Site Specific Data (SSD)____________________________ 14

2.18 Software (S/W) / System program ____________________ 14

2.19 Mixed system ____________________________________ 14

3Overview _________________________________ 15

3.1 The EBL512 G3 system ____________________________ 15

3.1.1 Printer ______________________________________ 15

3.1.2 Expansion boards _____________________________ 15

3.1.3 Power supply_________________________________ 15

3.2 S/W versions _____________________________________ 16

3.3 Documents ______________________________________ 16

3.4 Applications _____________________________________ 16

3.5 PC software (S/W) ________________________________ 16

3.5.1 Win512 version 2.7.x __________________________ 16

3.5.2 WinG3 version 1.1.x___________________________ 17

3.5.3 TLON Manager_______________________________ 17

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

3.5.4 Web512 II Config Tool 2.7______________________ 17

4Control Unit / TLON Network _______________ 18

4.1 The TLON network________________________________ 18

4.2 Single TLON Network / Redundancy in distributed system_ 18

5Control Units 5000 and 5001 _________________ 20

5.1 Mounting plates___________________________________ 22

5.1.1 Mounting plate for 19" mounting rack, 5020 ________ 22

5.1.2 Mounting plate for inflammable wall, 5021 _________ 22

5.2 COM loops ______________________________________ 23

5.3 Programmable voltage outputs (S0-S3) ________________ 25

5.4 Programmable relay outputs (R0-R1)__________________ 25

5.5 Programmable inputs (I0-I3)_________________________ 25

5.6 Relay outputs for routing equipment (tx) _______________ 26

5.6.1 Fire alarm output______________________________ 26

5.6.2 Fault condition output __________________________ 26

6Expansion boards 458x _____________________ 27

6.1 Expansion board no. (address) setting__________________ 28

6.2 8 zones expansion board 4580 _______________________ 28

6.2.1 Type of detectors = Type of zone line input _________ 29

6.2.2 Input states __________________________________ 30

6.3 8 relays expansion board 4581 _______________________ 31

6.4 I/O Matrix board 4582 _____________________________ 31

6.4.1 Generic _____________________________________ 33

6.4.2 Fan control __________________________________ 33

6.4.3 Zone control _________________________________ 34

6.5 Inputs and outputs expansion board 4583_______________ 34

6.6 External FBP / DU interface board 1587 _______________ 34

7Printer ___________________________________ 35

8TLON connection board 1590 ________________ 36

8.1 Single TLON Network _____________________________ 36

8.2 Network programming _____________________________ 36

9Peripheral devices__________________________ 37

9.1 COM loop units___________________________________ 37

9.1.1 Input units ___________________________________ 39

9.1.2 Addressable I/O units __________________________ 46

9.1.3 Alarm devices (addressable sounders) _____________ 48

9.1.4 Short circuit isolators (addressable) _______________ 49

9.1.5 Units for Hazardous (Ex) areas___________________ 50

9.1.6 Other COM loop units__________________________ 51

9.2 Units connected to the RS485 interface ________________ 53

9.2.1 External Fire Brigade Panels_____________________ 53

9.2.2 Alert Annunciation Units _______________________ 55

9.2.3 External Presentation Units______________________ 56

9.3 Units connected to the RS232 interface J7 ______________ 57

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

9.3.1 Web-servers__________________________________ 57

9.4 Other units_______________________________________ 57

9.4.1 Alert Annunciation Controllers___________________ 57

9.4.2 External LED ________________________________ 58

9.4.3 Alarm devices (sounders, etc.) ___________________ 58

9.4.4 Door release magnets __________________________ 58

9.4.5 Boxes_______________________________________ 59

9.4.6 Duct detector chambers_________________________ 59

10 Programmable inputs_______________________ 60

10.1 The 3361 unit's Inputs In0 / Z & In1___________________ 60

10.1.1 Input In0 ____________________________________ 60

10.1.2 Input In1 ____________________________________ 60

11 Input programming ________________________ 61

11.1 Trigger conditions_________________________________ 61

11.2 Logic ___________________________________________ 63

12 Programmable outputs______________________ 64

12.1 Control unit outputs S0 –S3_________________________ 65

12.2 Control unit outputs R0 & R1________________________ 65

12.3 8 relays expansion board 4581 Output 0 –Output 7_______ 65

12.4 The 3361 unit's Outputs Re0 & Re1 ___________________ 66

12.5 The 3364 unit's VO0 –VO2 _________________________ 66

12.6 The 3377 unit's Output (siren)________________________ 66

12.7 The 3379 unit's Output (sounder) _____________________ 66

12.8 The 4380 unit's Output (beacon)______________________ 66

13 Output programming_______________________ 67

13.1 Type of output____________________________________ 67

13.2 Logic ___________________________________________ 68

13.3 Supervised / Not supervised _________________________ 68

13.4 Time Activation Output ____________________________ 68

13.5 Control expression ________________________________ 71

13.5.1 Trigger conditions_____________________________ 71

13.5.2 Logical operators______________________________ 75

13.5.3 Control expression examples ____________________ 75

14 Interlocking function _______________________ 79

14.1 Programming of interlocking function _________________ 79

14.1.1 Interlocking output ____________________________ 79

14.1.2 Interlocking input _____________________________ 79

14.1.3 Interlocking combination _______________________ 79

14.2 Interlocking indications_____________________________ 81

14.3 Information of interlocking combinations (H9) __________ 81

14.3.1 Display interlocking information (H9/C1) __________ 81

14.3.2 Activate interlocking output (H9/C2) ______________ 81

14.3.3 Reset interlocking output (H9/C3) ________________ 82

14.3.4 Disable interlocking output (H9/C4)_______________ 82

14.3.5 Re-enable interlocking output (H9/C5)_____________ 82

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

14.4 Interlocking control expressions ______________________ 82

15 Fire Door Closing __________________________ 83

16 Functions / Services / Features _______________ 84

16.1 Sensor value _____________________________________ 84

16.2 Week average sensor value__________________________ 84

16.3 Decision value____________________________________ 85

16.4 Alarm algorithms for smoke detectors / Detection levels /

Offsets85

16.4.1 Alarm algorithm / Alternative alarm algorithm ______ 86

16.4.2 Filtering algorithm ____________________________ 87

16.4.3 Smouldering smoke algorithm ___________________ 89

16.5 Performance factor ________________________________ 90

16.6 Algorithms for analog heat detectors __________________ 91

16.6.1 Class A1 algorithm ____________________________ 92

16.6.2 Class A2 S algorithm __________________________ 92

16.6.3 Class B S algorithm____________________________ 92

16.7 Self verification___________________________________ 92

16.8 Minimum / Maximum sensor values___________________ 93

16.9 2-zone / 2-address dependence (Co-incidence alarm)______ 94

16.9.1 2-zone dependence ____________________________ 94

16.9.2 2-address (-unit) dependence ____________________ 95

16.9.3 Reset of 2-zone / 2-address dependence (co-incidence

alarm 95

16.10 Delayed alarm __________________________________ 96

16.11 Alarm Verification Facility________________________ 96

16.12 Alert Annunciation ______________________________ 97

16.13 Alarm Acknowledgement Facility (AAF)_____________ 99

16.14 Quiet alarm ___________________________________ 101

16.15 Fire alarm type A and Fire alarm type B_____________ 101

16.15.1 Fire alarm type B___________________________ 102

16.15.2 Fire alarm type A __________________________ 102

16.16 Disable alarm points and outputs __________________ 102

16.16.1 Disable zone ______________________________ 103

16.16.2 Disable zone / address_______________________ 103

16.16.3 Disable control output_______________________ 103

16.16.4 Disable / Re-enable output type _______________ 103

16.16.5 Disable / Re-enable alarm devices _____________ 103

16.17 Disable interlocking output_______________________ 103

16.18 Disable outputs for routing equipment ______________ 104

16.19 Disconnect & Re-connect loop / zone line input_______ 104

16.20 External time channels __________________________ 104

16.21 Test mode ____________________________________ 104

16.22 Test alarm devices______________________________ 105

16.23 Test of routing equipment________________________ 105

16.24 Calibration of supervised outputs __________________ 105

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

16.25 Service signal _________________________________ 105

16.26 Fault signal (fault condition)______________________ 106

16.27 Alarm texts ___________________________________ 106

16.27.1 Creating the alarm texts via Win512 version 2.7.x_ 107

16.27.2 Downloading alarm texts to the DU:s 1728 / 1735 /

1736 and ext. FBP:s 1826 / 1828________________________ 108

16.28 Real time clock (RTC) __________________________ 108

16.28.1 Daylight saving time ________________________ 109

16.29 Loss of main power source _______________________ 109

16.29.1 Fault: Loss of main power source ______________ 109

16.29.2 LCD backlight_____________________________ 109

16.30 Evacuate _____________________________________ 109

16.31 Win512 Tools menu ____________________________ 110

17 Redundancy in distributed system ___________ 112

17.1 Master and Slaves ________________________________ 112

17.1.1 Master unit _________________________________ 112

17.1.2 Slave unit___________________________________ 113

17.2 Several control units ______________________________ 115

17.2.1 Master unit _________________________________ 115

17.2.2 Several control units (slaves) ___________________ 115

18 Special New Zealand functions ______________ 118

18.1 Alarm devices ___________________________________ 118

18.1.1 Silence alarm devices (inside switch) _____________ 118

18.1.2 New Zealand FB Silence switch (outside switch)____ 118

18.2 Battery faults____________________________________ 120

18.2.1 FAULT: Battery _____________________________ 120

18.2.2 FAULT: Low battery capacity __________________ 120

18.3 Routing equipment isolate (disable) __________________ 120

18.4 Acknowledged alarm _____________________________ 120

19 Cyber sensor functions_____________________ 122

19.1 Pulse up –down counter ___________________________ 123

19.1.1 Pulse up –down counter for smoke ______________ 123

19.1.2 Pulse up –down counter for temperature __________ 123

19.1.3 Pulse up –down counter for smoke & temperature __ 123

19.2 Fire judgement __________________________________ 123

19.3 Alarm threshold levels ____________________________ 124

19.4 Learning function / Learning conditions_______________ 124

19.4.1 Learning conditions___________________________ 124

19.5 Alarm delay time_________________________________ 126

19.6 Analog data output _______________________________ 127

19.7 Sensitivity compensation __________________________ 127

19.8 Self diagnosis of internal devices ____________________ 128

19.9 Address setting check _____________________________ 128

20 Control unit properties (settings) ____________ 129

20.1 Control unit properties ____________________________ 129

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

20.1.1 General data ________________________________ 129

20.1.2 Type of control unit___________________________ 129

20.1.3 LED indications by inputs______________________ 130

20.1.4 Miscellaneous _______________________________ 130

20.1.5 Selective alarm presentation ____________________ 131

20.2 Log events______________________________________ 132

20.3 Log setup_______________________________________ 132

20.4 Control unit information ___________________________ 132

21 System properties (settings)_________________ 133

21.1 System data _____________________________________ 133

21.1.1 Logical name________________________________ 133

21.1.2 Alarm delay time_____________________________ 133

21.1.3 Main power loss fault delay time ________________ 133

21.1.4 Alarm reset _________________________________ 133

21.1.5 Door closing by time__________________________ 134

21.1.6 Miscellaneous _______________________________ 134

21.1.7 LCD in quiescent state ________________________ 135

21.2 Time channels ___________________________________ 135

21.3 Time activation output ____________________________ 135

21.4 Door open ______________________________________ 136

21.4.1 Indication door open affected by_________________ 136

21.4.2 Disablement of routing equipment _______________ 136

21.5 National holidays ________________________________ 137

21.6 Alarm algorithms ________________________________ 137

21.6.1 Classic smoke detectors' properties_______________ 137

21.6.2 Heat detectors' (3308, 3309, 3316 and 4300) properties138

21.6.3 Smoke detectors' (3304, 4301, 3316 and 4300) properties139

21.6.4 Multi detectors' (3316 and 4300 + decision algorithm)

properties __________________________________________ 139

21.7 System information_______________________________ 140

21.8 Alert Annunciation and Alarm Acknowledgement Facility 140

21.8.1 Alert Annunciation ___________________________ 140

21.8.2 Alarm Acknowledgement Facility _______________ 140

21.9 Two zone dependence_____________________________ 140

22 Compatibility_____________________________ 142

23 Cable types ______________________________ 143

23.1 TLON Network cables ____________________________ 143

23.2 COM loop cables_________________________________ 143

23.3 Ext. FBP / Display Units cables _____________________ 143

23.4 Conventional zone line cables_______________________ 143

23.5 Alarm device cables ______________________________ 144

23.6 Other cables_____________________________________ 144

24 COM loop cable length_____________________ 145

25 Current consumption ______________________ 148

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

26 Power supply_____________________________ 152

26.1 Charger functions ________________________________ 153

26.1.1 Charging ___________________________________ 153

26.1.2 Battery charging functions:_____________________ 153

26.1.3 Security functions ____________________________ 153

26.2 Current consumption calculations____________________ 154

26.3 Rectifier (main power source)_______________________ 155

26.4 Battery (second power source) ______________________ 155

26.5 Fuses __________________________________________ 156

26.6 Form / Table of current consumption _________________ 157

27 S/W versions _____________________________ 158

28 Technical data____________________________ 159

29 Limitations_______________________________ 160

29.1 User definable texts_______________________________ 160

29.2 C.i.e. / System ___________________________________ 160

30 National regulations _______________________ 162

31 Drawings / connection diagrams_____________ 163

32 Revision history___________________________ 164

Drawings according to the valid table of drawings.

Panasonic Eco Solutions Nordic AB

MEW01472 Rev: - Planning Instructions Fire alarm system EBL512 G3, United version 2.7.x

Otros manuales para EBL512 G3 5000

Tabla de contenidos

Otros manuales de Unidad de control de Panasonic

Panasonic

Panasonic PAN1322-SPP Manual de usuario

Panasonic

Panasonic PAN1740A Guía de configuración rápida

Panasonic

Panasonic CATU9000U - AV CTRL AMP Manual de usuario

Panasonic

Panasonic CF-BAV0512U Manual de usuario

Panasonic

Panasonic SF-C21 Manual de usuario

Panasonic

Panasonic INDUSTRY PAN9028 Manual de usuario

Panasonic

Panasonic GP-KS162CUDE Manual de usuario

Panasonic

Panasonic AJRC10G - REMOTE CONTROL UNIT Manual de usuario

Panasonic

Panasonic FZ-VCN55 Series Manual de usuario

Panasonic

Panasonic BMED500 - CAMERA CONTROL UNIT Manual de usuario

Panasonic

Panasonic GP-KH232CUE Manual de usuario

Panasonic

Panasonic SL-PC104 Manual de usuario

Panasonic

Panasonic eUniStone Guía

Panasonic

Panasonic CF-BAC02GU Manual de usuario

Panasonic

Panasonic PAN1326C Guía

Panasonic

Panasonic PAN4620 Manual de usuario

Panasonic

Panasonic CF-BAD02GU Manual de usuario

Panasonic

Panasonic CF-BAJ0256U Manual de usuario

Panasonic

Panasonic WVPS15 - CAMERA DRIVE UNIT Manual de usuario

Panasonic

Panasonic AK-HCU931 Manual de usuario

Panasonic

Panasonic PAN1326C2 Manual de usuario

Panasonic

Panasonic CF-BAU0512U Manual de usuario

Panasonic

Panasonic CF-BAU0256U Manual de usuario

Panasonic

Panasonic CARICAM AU-VSHL2G Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario