Panasonic CF-VCW283 Manual de usuario

CD-R/RW Drive Pack

CD-R/RW ドライブパックドライブパック

ドライブパックドライブパック

ドライブパック

CF-VCW283

Introduction........................................................... 4

Usage Precautions ............................................... 5

Using the Drive ..................................................... 6

Troubleshooting ................................................. 10

Specifications ..................................................... 11

OPERATING INSTRUCTIONS

ENGLISH

Einführung........................................................... 12

Vorsichtsmaßnahmen zum Gebrauch .............. 13

Gebrauch des Laufwerks ................................... 14

Störungsbehebung ............................................. 18

Technische Daten ............................................... 19

BEDIENUNGSANLEITUNG

DEUTSCH

Introduction......................................................... 20

Précautions d’utilisation .................................... 21

Utilisation du lecteur .......................................... 22

Dépannage .......................................................... 26

Spécifications ..................................................... 27

MODE D’EMPLOI

FRANÇAIS

はじめにはじめに

はじめに ..........................................................................

..........................................................................

.....................................

安全上のご注意安全上のご注意

安全上のご注意 ..............................................................

..............................................................

...............................

使用上のお願い使用上のお願い

使用上のお願い ..............................................................

..............................................................

...............................

ドライブを使うドライブを使う

ドライブを使う ..............................................................

..............................................................

...............................

困ったときの困ったときの

困ったときの

Q&A

..........................................................

.............................

仕様仕様

仕様 ..................................................................................

..................................................................................

.........................................

保証とアフターサービス保証とアフターサービス

保証とアフターサービス ..............................................

..............................................

.......................

取扱説明書取扱説明書

取扱説明書

日本語日本語

日本語

保証書付き（日本国内向け）

・この取扱説明書と保証書をよくお

読みのうえ、正しくお使いくださ

い。そのあと保存し、必要なとき

にお読みください。

・保証書は「お買い上げ日・販売店

名」などの記入を必ず確かめ、販

売店からお受け取りください。

FJ0403-0

DFQX5392ZA

Printed in Japan

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RA-

DIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL

WARNUNG!

DIESES PROUKT ERZEUGT LASERSTAHLUNG.

DURCHFÜHRUNG ANDERER VORGÄNGE ALS DER HIER ANGEGEBENEN KANN

ZU GEFÄHRLICHER STRAHLUNG FÜHREN.

REPARATUREN DÜRFEN NUR VON QUALIFIZIERTEM FACHPERSONAL

DURCHGEFÜHRT WERDEN.

AVERTISSEMENT!

CET APPAREIL UTILISE UN LASER.

L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCUTION DE

PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER UNE

EXPOSITION À DES RADIATIONS DANGEREUSES.

NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOI-MÊME.

CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.

VARNING

Om apparaten används på annat sätt än i denna bruksanvisnig specificerats, kan användaren

utsättas för osynlig laserstrålning, som överskrider gränsen for laserklass 1.

CLASS 1 LASER PRODUCT

LASER KLASSE1

For U.S.A.

Federal Communications Commission Radio Frequency Interference

Statement

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

Consult the Panasonic Service Center or an experienced radio/TV technician for help.

Warning

To assure continued compliance, use only shielded interface cables when connecting to a

computer or peripheral. Also, any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

Responsible Party: Matsushita Electric Corporation of America

One Panasonic Way

Secaucus, NJ 07094

Tel No:1-800-LAPTOP-5 (1-800-527-8675)

For Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Thank you for purchasing the CD-R/RW Drive Pack for the Panasonic CF-28 notebook

computer series.

This drive connects to the computer through the Multimedia Pocket.

Store this manual in a safe place after reading it.

CD-R/RW Drive Pack*................1

Introduction

[Illustration in this manual]

Windows 98 indicates Microsoft®Windows®98 Second Edition Operating System.

Windows 2000 indicates Microsoft®Windows®2000 Professional Operating System.

Windows XP indicates Microsoft®Windows®XP Professional Operating System.

Operating Instructions ..............1

Easy CD Creator™ 5 Basic CD-ROM ...... 1

Easy CD Creator™ 5 Basic Leaflet .. 1

Microsoft®, MS-DOS®and Windows®are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

Roxio, the Roxio logo, Easy CD Creator and DirectCD are trademarks of Roxio, Inc. which may be

registered in some jurisdictions.

*The CD-R/RW Drive Pack may also be referred to as the drive.

Windows XP

This manual explains the procedure for default settings. The procedure may differ

according to the settings.

NOTE

Usage Precautions

If the disc gets dirty

After wiping the disc with a moist, soft cloth, wipe it with a dry cloth. Always wipe from

the center toward the edge.

Do not place items other than discs on the tray.

Do not leave the tray in the open position or touch the lens area. Should the lens

become soiled by dust or dirt, the unit may not read discs properly.

Under some conditions, dust may build up on the optical lens or disc, possibly resulting in

malfunction.

Do not apply excessive force to the tray in the open position, doing so could damage the

tray.

Do not open the drive or move the computer while the drive is being accessed. Doing so

could cause it to malfunction. In addition, after running an application involving access to

a disc, do not open the drive or remove the disc until after the application has been closed.

After closing the tray, do not attempt to access a disc until the MP indicator ( ) disap-

pears.

Do not expose the drive to oily or tobacco smoke. Doing so could shorten the service life

of the lens.

If the drive malfunctions, we recommend cleaning the lens with a blower used for camera

lenses. (Do not use strong, cleaning sprays.)

Never insert foreign objects such as paper clips into the drive.

Do not use discs that have become deformed (warped, not completely round, etc.).

When the drive is installed, do not use an external drive (CD-ROM drive, DVD-ROM

drive, etc.).

For AutoPlay CDs:

• If an AutoPlay CD does not start after the computer resumes from the standby or hiber-

nation mode, we recommend reinserting the CD again after a 15-second wait.

• An AutoPlay CD may start during the access of a file.

To avoid damaging discs:

Do not touch the surface as it can cause the disc to become dirty or scratched.

Do not allow discs to become dirty or scratched.

Do not place or store discs in locations exposed to heat, direct sunlight, humidity or dust.

Do not write on the surface of the disc with a ball-point pen or other writing instrument.

If the disc is brought from a cold into a warm environment, moisture may form on the disc.

Wipe this moisture off with a soft, dry, lint-free cloth before using the disc.

Do not drop, bend, or place heavy objects on top of discs.

Cleaning the disc using a CD cleaner is recommended once every 2 or 3 months.

Using the Drive

Refer to the Reference Manual included with your computer on how to install/remove the drive.

Installing/Removing a Drive

Preparations

Windows 98

Confirm the following contents in [Start] - [Settings] - [Control Panel] - [System] - [Device

Manager] - [CDROM] - [MATSHITA UJDA***] - [Properties] - [Settings]. Make the set-

tings if they have not yet been made.

• Add a check mark for [DMA].

• Set both [Start drive letter] and [End drive letter] in [Reserved drive letters] to [L:].

Windows 2000

Confirm that [Transfer Mode] is set to [DMA if available] in [Start] - [Settings] - [Control

Panel] - [System] - [Hardware] - [Device Manager] - [IDE ATA/ATAPI controllers] - [Sec-

ondary IDE Channel] - [Advanced Settings] - [Device 0]. Perform this setting if it has not

yet been made.

Windows XP

Confirm that [Transfer Mode] is set to [DMA if available] in [start] - [Control Panel] -

[Performance and Maintenance] - [System] - [Hardware] - [Device Manager] - [IDE ATA/

ATAPI controllers] - [Secondary IDE Channel] - [Advanced Settings] - [Device 0]. Perform

this setting if it has not yet been made.

Be sure to turn the computer off before installing/removing the drive.

CAUTION

If the PC Card does not work, there may be no interrupt request (IRQ) line available.

Deactivate unnecessary equipment using in Setup Utility.

NOTE

Center Holder

Eject Button

Label side up

1Power on your computer

2Open the disc tray

Press the eject button and slowly pull out the tray.

3Place a disc

1Place the disc with the label facing upward in the

drive.

2Push down until the center holder clicks.

Place a finger on the center holder and lift up on the

edge of the disc.

4Close the disc tray

Close the tray without touching the eject button.

NOTE

If the drive has not been accessed within 30 seconds, the drive motor will automatically shut

down to reduce the power consumption. When the drive is accessed once again, the power

of the drive motor is turned on. However, approximately 30 seconds are required until data

is actually read from the disc.

Power-saving Mode

Setting a Disc

If the vibration of the drive is excessively high, use the Setup Utility to reduce the

drive speed by setting it to [Low].

Windows 98

In the following cases, the drive speed may not be set to [Low]. At a time like this,

restart your computer.

• When operation is resumed from the standby or hibernation mode

• When a drive has been installed while the power was still on

NOTE

Before using the drive for the first time, re-

move the protective sheet from the lens area.

The protective sheet inside the drive delays

the opening of the drive by about ten seconds.

This delay is not a problem.

Windows 98

To use the drive in the MS-DOS mode*, configure the drive following the steps below after

performing the preparations ( page 6). If the steps listed below are performed with-

out completing the preparations first, the drive will not operate properly.

*In the MS-DOS mode, discs can only be read.

Using the Drive in the MS-DOS Mode

1Select [Start], then select [Shut Down].

2Select [Restart in MS-DOS mode], then select [OK].

3Open the “CONFIG.SYS” file for editing by issuing the following commands:

cd \ Enter

edit config.sys Enter

4Move the cursor to the line containing “OAKCDROM.SYS” and delete the characters

“rem” at the beginning of the line. (Deleting “rem” causes the item to become valid.)

DEVICEHIGH=C:\WINDOWS\COMMAND\OAKCDROM.SYS /D:MSCD000

(If this line is missing, add it.)

5Press Alt + F(File),then S(Save) to save the file. Then press Alt + F, then

X(Exit) to exit the Edit program.

6Follow the same steps to edit the “AUTOEXEC.BAT” file.

edit autoexec.bat Enter

7Move the cursor to the line containing “MSCDEX.EXE” and delete the characters “rem”

at the beginning of the line. (Deleting “rem” causes the item to become valid.)

LOADHIGH C:\WINDOWS\COMMAND\MSCDEX.EXE /D:MSCD000 /L:L

(If this line is missing, add it.)

8Press Alt + F, then Sto save the file. Then press Alt + F, then Xto exit

the Edit program.

9Restart the computer.

Using the Drive

When using CD-R or CD-RW discs, read the descriptions on the disc packages.

CD-RW discs cannot be read with other drives*unable to accommodate CD-RW discs.

*Consult with the manufacturer of each drive.

Using the CD-ROM of the CD-R/RW writer software (included), install the application

software on your computer. For information on how to install the software, refer to the

included manual of the CD-R/RW writer software.

Be sure to use discs conforming to the proper write speeds. ( page 11)

If the write operation is to involve a long period of time, be sure to connect the AC

adaptor. If the battery power runs low and the power of the computer is cut, the write

operation may end in failure.

Depending on the disc, the quality of the write operation may not be so good. We recom-

mend using any of the following discs.

Recommended Discs:

<CD-R>

HITACHI MAXELL, Ltd.

MITSUBISHI CHEMICAL Co., Ltd.

MITSUI CHEMICALS, Inc.

RICOH Co., Ltd.

TAIYOYUDEN Co., Ltd.

<CD-RW/High Speed CD-RW>

MITSUBISHI CHEMICAL Co., Ltd.

RICOH Co., Ltd.

When writing to CD-R/RW discs

Check the settings by following the instructions

in “Preparations” ( page 6).

Is the drive properly mounted in the multimedia pocket?

Is the disc loaded on the tray correctly?

Is the disc bent, scratched, or dirty?

Is the computer powered on?

To remove a disc when the

computer is powered off, in-

sert a pointed object such as

the bent-out tip of a paper clip

into the emergency hole.

Pushing it completely to the

end will free the tray so that it

can be pulled out.

Did you open the drive or remove the disc while it

was operating?

Re-insert the disc and close the drive. Press

Enter .

Did you touch the eject button when you close the tray?

Is an external drive (CD-ROM drive, DVD-ROM

drive, etc.) connected?

When the drive is installed, do not use an external

drive (CD-ROM drive, DVD-ROM drive, etc.).

Was the computer turned off before the instal-

lation/removal of the drive?

The computer needs to be off so that the drive

can properly initialize during Windows startup.

When the CD-ROM drive or DVD-ROM drive is

replaced after the CD-R/RW drive has been in-

stalled in the Multimedia Pocket, files inside the

drive sometimes cannot be accessed.

In this case, execute [Scan for hardware changes]

using the following procedure.

1Select [Device Manager] in [start] - [Control

Panel] - [Performance and Maintenance] - [Sys-

tem] - [Hardware] .

2Select the drive displayed under [DVD/CD-

ROM drives] (e.g., MATSHITA****), then se-

lect [Action] - [Uninstall] from the menu and

select [OK].

3Select [Action] - [Scan for hardware changes]

from the menu. (Microsoft Corp. has reported

that the above noted problem occurs.)

Troubleshooting

The computer does not recognize

the drive

The MP indicator ( ) does not light

Cannot play disc or read data from it

Cannot eject disc

A blue background appears on the

screen with the MPEG image

The disc tray does not close

The computer hangs or restarts

Windows XP

Cannot access file for CD-ROM

drive or DVD-ROM drive

Emergency Hole

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de CD/CDR de Panasonic

Panasonic

Panasonic LK-MC606BP Manual de usuario

Panasonic

Panasonic KX-LD721 Manual de usuario

Panasonic

Panasonic LK-MW602SK Manual de usuario

Panasonic

Panasonic LF-1004AB Manual de usuario

Panasonic

Panasonic CF-VCD271 Manual de usuario

Panasonic

Panasonic CF-VCW282U Manual de usuario

Panasonic

Panasonic KX-L783A Manual de usuario

Panasonic

Panasonic CW-7586-J Manual de usuario

Panasonic

Panasonic KX-LD742 Manual de usuario

Panasonic

Panasonic KX-LRW21A Manual de usuario

Panasonic

Panasonic KX-LD721 Manual de usuario

Panasonic

Panasonic LF-1007AD Manual de usuario

Panasonic

Panasonic KX-LD740 Manual de usuario

Panasonic

Panasonic CF-VCD252 Manual de usuario

Panasonic

Panasonic CF-VCW721 Manual de usuario

Panasonic

Panasonic CF-VCW281 Manual de usuario

Panasonic

Panasonic CF-VCW722W Manual de usuario

Panasonic

Panasonic KX-LRW10A Manual de usuario

Panasonic

Panasonic KX-L807A Manual de usuario

Panasonic

Panasonic CF-VCW Series Diagrama de cableado

Panasonic

Panasonic KX-LD745 Manual de usuario

Panasonic

Panasonic KX-L783M Manual de usuario

Panasonic

Panasonic KX-L840A Manual de usuario

Panasonic

Panasonic CW-7586-B Manual de usuario

Manuales populares de Unidad de CD/CDR de otras marcas

Philips

Philips CDD3610 Manual de usuario

QPS

QPS Que!Fire Manual de usuario

LG GCC-4241N Manual de usuario

Plextor

Plextor 12X-3 Guía

Samsung

Samsung SN-324B Manual de usuario

Teac

Teac CD-211E Manual de usuario

SmartDisk

SmartDisk Firewire CD-R/W Manual de usuario

Axis

Axis CD-ROM SERVER Manual de usuario

LG CRD-8322B Manual de usuario

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Instrucciones de instalación

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 Manual de usuario

Sony

Sony CRX230AE Manual de usuario

Sony

Sony CRX - 160E Manual de usuario

Pioneer

Pioneer BDR-S13U-X Manual de usuario

LG CRD-8320B Manual de usuario

Conner

Conner CFP2107 Series Manual de usuario

Sony

Sony CRX-1611 Manual de usuario

Plextor

Plextor 12-20C Guía