Panasonic CQ-VD6503W Manual de usuario

2CQ-VD6503W

English

Safety Information

CAUTION:

• PLEASE FOLLOW THE LAWS AND REGULATIONS

OF YOUR STATE, PROVINCE OR COUNTRY FOR

INSTALLATION OF THE UNIT.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE

THIS APPLIANCE TO RAIN, SPLASHING, DRIP-

PING OR MOISTURE.

6503WII01eng06.2.202:33PMページ2

CQ-VD6503W

English

Upgrade Options

Safety Information................................................2

Upgrade Options ..................................................3

Contents................................................................3

Installation Guide .................................................4

Electrical Connections ........................................8

Contents

Display Unit

CQ-VD6503W

Expansion Module

(CY-EM100N, option)

Hands-Free Kit featuring

Bluetooth®technology

(CY-BT100N, option)

CD Changer

(CX-DP880, option)

DVD Changer

(CX-DH801W, option)

Rear Monitor

iPod

TV Tuner

(CY-TUP133W,

CY-TUN133W option)

6503WII01eng06.2.202:33PMページ3

4CQ-VD6503W

English

Installation Guide

Preparation Dashboard Installation

¡Before installation, check the radio operation with

antenna and speakers.

¡Disconnect the cable from the negative (–) battery ter-

minal (see caution below).

¡The unit should be installed in a horizontal position

with the front end up at a convenient angle, but not

more than 30°.

Installation Opening

The unit can be installed in any dashboard having an

opening as shown below. The dashboard should be 4.5

mm – 6 mm thick in order to be able to support the unit.

Installation Precautions

This product should be installed by a professional

installer, if possible.

In case of difficulty, please consult your nearest author-

ized Panasonic Service Centre.

1. This system is to be used only in a 12 V DC battery

system (car) with negative ground.

2. Follow the electrical connections carefully (a page 8-

16). Failure to do so may result in damage to the unit.

3. Connect the power lead after all other connections are

made.

4. Be sure to connect the battery lead (yellow) to the pos-

itive terminal (+) of the battery or fuse block (BAT) ter-

minal.

5. Insulate all exposed wires to prevent short circuiting.

6. Secure all loose wires after installing the unit.

7. Please carefully read the operating and installation

instructions of the respective equipment before con-

necting it to this unit.

0 – 30°

182 mm

111.6 mm

Caution

¡Do not disconnect the battery terminals of a car with

trip or navigational computer since all user settings

stored in memory will be lost. Instead take extra

care with installing the unit to prevent shorts.

Caution

¡Please follow the laws and regulations of your

province or country for installation of the unit.

¡When bending the mounting tab of the mounting

collar with a screwdriver, be careful not to injure

your hands and fingers.

¡We strongly recommend you to wear gloves for

installation work to protect yourself from injuries.

6503WII01eng06.2.202:33PMページ4

CQ-VD6503W

English

Lock Cancel Plate

❏Transportation Bracket Removal

Be sure to remove the transportation brackets before

use (installation). Use round head screws (5 mmøx 8

mm) for installation. (apage 7)

Be careful not to lose these screws.

Round Head Screw (5 mmøx 8 mm)

Transportation Bracket

❏Installation Hardware

(For Installation)

Note:

¡The number in parenthesis underneath each accessory

part name is the part number for maintenance and

service.

¡Accessories and their parts numbers are subject to

modification without prior notice due to improvements.

¡Mounting Collar wis mounted on the main unit at

shipment.

¡Use the supplied screws for installation exclusively. In

case of losing any of them, please order the specific

screw.

Qty.DiagramItemNo.

Trim Plate

Mounting Collar

Rear Support Strap

Round Head Screw

(5 mmø x 8 mm)

Flat-Head Screw

(5 mmø x 8 mm)

Mounting Bolt (5 mmø)

Tapping Screw

(5 mmøx 16 mm)

Hex. Nut (5 mmø)

❏Before Installation

Caution

¡Do not press the panel forcefully.

¡Do not scratch the panel with fingernails or any hard

objects.

¡Do not bump the front panel.

aFailure to observe the above may damage or

break the glass on the surface of the touch panel.

❏Installation Hardware

(For Wiring)

Qty.DiagramItemNo.

Power Connector

(ISO connector)

!0 1

Reverse Extension Cord

!1 1

Clip Connector

!2 1

6503WII01eng06.3.66:32PMページ5

6CQ-VD6503W

English

Installation Guide (continued)

❏Mounting Procedures (A) (When using Mounting Collar w)

Mounting and removing the Display Unit

Note:

¡The car model, installation conditions and combination

of the units used may impose some restrictions on

opening and closing the monitor as well as on the

angle and position to which the monitor can be adjust-

ed.

IMPORTANT

When this unit is installed in dashboard, ensure that there

is sufficient air flow around the unit to prevent damage

from overheating. Do not block any ventilation holes on

the unit.

Insert the Mounting Collar winto the dash-

board, and bend the mounting tabs out with

a screwdriver.

Establish the rear connection of the unit.

After fixing Power Connector !0, fix the rear

of the unit to the car body by either method

(a) or (b).

Insert the unit into Mounting Collar w.

Secure the clamp plate of Mounting Collar w

to the hook.

Insert Trim Plate q.

After installation reconnect the negative (–)

battery terminal.

Snapping point

(a) Using the Rear Support Strap u.(b) Using the Rubber Cushion (option)

Fire wall of car

3 mmø

tTapping Screw

(5 mmø x 16 mm)

uRear Support

Strap

rMounting Bolt

(5 mmø)

To the unit

rMounting Bolt

(5 mmø)

Rear Support

Bracket

(Provided on

the Car)

Rubber Bushing

(option)

yHex. Nut

(5 mmø)

Method for Fixing the Rear of the Unit

6503WII01eng06.2.202:33PMページ6

CQ-VD6503W

English

❏Mounting Procedures (B)

(When not using Mounting Collar w)

Use the brackets supplied with your car when mounting

this unit. The bracket shape and mounting method vary

with car manufacturers, car types and manufacturing

year. Please consult your nearest dealer or installer.

❏Removing Procedures

qRemove the trim plate q.

wLock release.

qInsert the lock cancel plate euntil you hear a

click.

wPull the unit out.

ePull the unit out with both hands.

Note: Use pliers to bend the

fingers on the bracket vertically.

Select mounting screws according to the hole

positions and hole shape of the bracket.

iRound Head Screw

(5 mmø x 8 mm)

Note:

Recycle the Round Head Screws that fixed the

transportation brackets for two more

positions. (apage 5)

oFlat-Head Screw

(5 mmø x 8 mm)

6503WII01eng06.2.202:33PMページ7

8CQ-VD6503W

English

FUSE 15AFUSE 15AFUSE 15A

8mmMAX

>PBT< JAM- S Aa

AV-OUT

CAMERA-IN

2 41

Electrical Connections

Caution

¡This unit is designed for use in a car having a 12 V negative ground battery system.

¡Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from

any metal parts.

¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery

may clear the memory.

¡Run the cords avoiding the spots where the temperature can be extremely high.

Video Output Terminal (AV-OUT)

Connect the rear monitor. (apage 15)

Pre-Out Connector (front)

To external amplifier.

Pre-Out Connector (rear)

To external amplifier.

Pre-Out Connector (center)

To external amplifier. Video Input Terminal (AV1-IN)

Video Input Terminal (AV2-IN)

Note: When an external device is connected

to the system-up connector, the audio termi-

nals, {(R)(Red), (L)(White)}, of AV2-IN are

disabled.

Connect a VCR, camcorder, other brand’s car

navigation system, etc. (apage 15)

Camera Input Terminal (CAMERA-IN)

Connect a rear view camera. (apage 16)

(R)(Red)

(L)(White)

(Yellow)

(R)(Red)

(Black) (White)

(Red)

(Black)

(L)(White)

(Yellow)

Pre-Out Subwoofer connector (mono)

To external amplifier.

Fuse (15 A) Refer fuse replacement to your nearest

authorized Panasonic Service Centre. Do not try fuse

replacement by yourself.

CQ-VD6503W

(Rear)

6503WII01eng06.3.66:32PMページ8

CQ-VD6503W

English

FRONT SP

SIDE BRAKE

REVERSE

ACC

BATTERY 15A

REAR SP

Note:

¡To prevent from damage to the unit, be sure to follow the wiring diagrams below.

¡Be sure to fully plug in the connectors. Secure them with clamps and tapes.

¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or

your dealer if other methods are required.

: This book refers to connections to the Panasonic car navigation system that will come onto the market in the

future. Descriptions regarding the car navigation system are boxed with a dotted line.

Radio Antenna Connector (RADIO ANT IN)

RGB Connector

To the Panasonic Car Navigation System (available in future).

System-up Connector

To external devices equipped with system-up connector.

!0 Power Connector

Motor Antenna Relay Control Lead (Blue)

(To motor antenna) (Max. 100 mA)

This lead is not intended for use with a switch actuated power

antenna.

External Amplifier Control Power Lead (Blue/white stripe)

To an external amplifier.

Note:

¡Use the power control lead of the TV tuner for TV

tuner connection.

¡Connect both the power control lead of the TV tuner

and the amplifier control connector of the external

amplifier when the TV tuner and external amplifier are

connected at the same time.

Navi Mute Lead (Orange)

Connect to the Navi Mute Lead of the Panasonic car

navigation system. (available in future)

Side Brake (Parking Brake) Connection Lead (Bright green)

Be sure to wire the side brake (parking brake) for safety and pre-

venting accidents. (apage 10)

Reverse Lead (Violet/white stripe)

When connecting the rear view camera, use the reverse

lead. (apage 16)

Battery Lead (Yellow)

To the car battery, continuous +12 V DC.

Power Lead (Red)

To ACC power, +12 V DC.

Front Right + (Gray)

Front Right – (Gray/black stripe)

Front Left + (White)

Front Left – (White/black stripe)

Rear Right + (Violet)

Rear Right – (Violet/black stripe)

Rear Left + (Green)

Rear Left – (Green/black stripe)

Speaker connections

• Do not connect more than one speaker to one set of

speaker leads (except for connecting to a tweeter).

• Do not use a 3-wire type speaker system having a

common earth lead.

Ground Lead (Black)

To a clean, bare metallic part of the car chassis

Note:

Use a Reverse Extension Cord

if needed.

6503WII01eng06.2.202:33PMページ9

10 CQ-VD6503W

English

—

SIDE BRAKE

The side brake (parking brake) switch position varies with car model.

For details on the exact location of the side brake (parking brake) switch

in your car, contact your dealer.

qAttach a Clip Connector !2 to the end of the side

brake (parking brake) connection lead.

wThe Clip Connector !2 is connected to the power

source side lead of the side brake (parking brake)

lever.

Connecting the Side Brake (Parking Brake) Connection Lead

Hand brake Foot brake

Side Brake (Parking Brake) Connection

Lead (Bright green)

When the side brake (parking brake) lever is

engaged, the unit is grounded by the chassis.

Side brake (parking brake) switch

Car chassis

Battery

Brake light

!2 Clip Connector

Side Brake (Parking Brake) Connection Lead

(Bright green)

Comes up to this point.

Power source side lead

Caution

¡For safety, be sure to ask your nearest professional installer to do this connection.

Electrical Connections (continued)

6503WII01eng06.2.202:33PMページ10

CQ-VD6503W

English

Connection with TV Tuner

Note:

¡Refer to the operating instructions for the connected devices, in addition.

FUSE 15AFUSE 15AFUSE 15A

8mmMA X

>PBT< JAM- S Aa

PWR-CONT

TV Tuner

CY-TUP133W/

CY-TUN133W (option)

CQ-VD6503W

(Rear)

(Video)

(Yellow)

System-up Connector

(supplied with CY-TUP133W/

CY-TUN133W)

System-up Connector

!0 Power Connector

Power Control

Lead

RCA Cord

(supplied with CY-TUP133W/CY-TUN133W)

External Amplifier Control Power Lead

Note:

¡Connect both the power control lead of the TV

tuner and the amplifier control connector of the

external amplifier when the TV tuner and external

amplifier are connected at the same time.

Power Connector

(supplied with CY-TUP133W/

CY-TUN133W)

Clip Connector

(option)

6503WII01eng06.3.66:32PMページ11

Otros manuales para CQ-VD6503W

Tabla de contenidos

Otros manuales de Receptor de coche de Panasonic

Panasonic

Panasonic CQ-DFX883N Manual de usuario

Panasonic

Panasonic CQ-5101U Manual de usuario

Panasonic

Panasonic CQ-DFX572N Manual de usuario

Panasonic

Panasonic CQ-RD555LEN Manual de usuario

Panasonic

Panasonic CQ-DP30EN Manual de usuario

Panasonic

Panasonic RM-1100 Manual de usuario

Panasonic

Panasonic CQC1101U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQDFX883U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQ-RD324N Manual de usuario

Panasonic

Panasonic CQDF602U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQVD7001U - CAR A/V DVD NAV Manual de usuario

Panasonic

Panasonic CQ-R45EN Manual de usuario

Panasonic

Panasonic CQHX1083U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQDPX172U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic Car Kit Manual de usuario

Panasonic

Panasonic CQ-FX721N Manual de usuario

Panasonic

Panasonic CQ-VA7800N Manual de usuario

Panasonic

Panasonic CQ-RX400N Manual de usuario

Panasonic

Panasonic CQDFX983U - AUTO RADIO/CD DECK Instrucciones de montaje

Panasonic

Panasonic 5300U Manual de usuario

Panasonic

Panasonic CQC8313U - CAR AUDIO-MULTI-LANG Manual de usuario

Panasonic

Panasonic CQC1304U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQ-5800U - Double DIN Heavy Duty MP3 Manual de usuario

Panasonic

Panasonic CQ-DFX777EW Manual de usuario

Manuales populares de Receptor de coche de otras marcas

Motorola

Motorola VWA63 Manual de usuario

Nextar

Nextar D3201 Manual de usuario

Alpine

Alpine CDE-163BT Manual de usuario

Pioneer

Pioneer DEH-P645R Manual de usuario

Axxera

Axxera XDMA7600 Instrucciones de funcionamiento

XM OnyX Manual de usuario

Sound Storm

Sound Storm STM93R Manual de usuario

Soundstream

Soundstream VIR-5000 Manual de usuario

Avson

Avson MKT Platform Manual de usuario

Sony

Sony MEX-1HD - Audio Library System Manual de usuario

Pioneer

Pioneer DVH-P500UB Manual de usuario

JVC

JVC KD-AHD69 Manual de usuario

Blaupunkt

Blaupunkt SANTIAGO CR 87 Manual de usuario

Sony

Sony CDX-4160 - Cd Receiver Manual de usuario

XFIRE AUDIO

XFIRE AUDIO BMW42S Manual de usuario

VDO

VDO CD 2253 Manual de usuario

Volvo

Volvo 13 84 580 Manual de usuario

ZENEC

ZENEC ZE-160DVD Manual de usuario