Panasonic ET-D3LEW10 Manual de usuario

Thank you for purchasing this Panasonic product.

■To ensure correct use of this lens, please read the operating instructions supplied

with the lens and the projector carefully.

■Before using this product, be sure to read “Read this rst!” (Page 3).

■Please save this manual for future use.

Commercial Use

Model No. ET-D3LEW10

DPQX1300ZA/X1

Zoom Lens 　　　　　　　　　

Operating Instructions

ENGLISH

2-ENGLISH

Read this rst! ......................................................................................3

Before Use.............................................................................................4

Attaching the Lens / Detaching the Lens...........................................5

Before replacing the projection lens........................................................ 5

Attaching the Lens...................................................................................5

Peripheral focus adjustment function ...................................................... 7

Lens calibration ....................................................................................... 8

Removing the Lens ................................................................................. 9

Projection relationships.....................................................................10

Lens shift ranges................................................................................11

Specications .....................................................................................12

Dimensions .........................................................................................12

Projected image size and Projection distance.......Appendix / Annexe / 付録 1

The "Appendix" can be found after the Japanese language section ( 日本語 ).

█ Contents

ENGLISH-3

Read this rst! Always follow these precautions

WARNING:

Do not look at or place your skin into the light emitted from the lens while the

projector is being used.

Doing so can cause burns or loss of sight.

zStrong light is emitted from the projector’s lens. Do not look at or place your hands

directly into this light.

zTurn off the power when moving away from the projection lens or projector.

Do not project an image with the lens cover attached.

zDoing so can cause re.

CAUTION:

Before replacing the projection lens, be sure to turn off the power and

disconnect the power plug from the wall outlet.

zUnexpected projection of light may cause injury to eyes.

zReplacing the projection lens without removing the power plug may result in electric

shock.

Do not stand in front of the lens while the projector is being used.

Doing so can cause damage and burns to clothing.

zStrong light is emitted from the projector’s lens.

Do not place objects in front of the lens while the projector is being used.

Doing so can cause re, damage to the object, or malfunction of the lens and

projector.

zStrong light is emitted from the projector’s lens.

Do not open the desiccant bag. Do not eat the contents.

Inadvertently ingesting desiccant could be harmful.

zIf the desiccant gets into your eyes or mouth, immediately rinse with plenty of water

and seek medical attention.

zKeep desiccant out of the reach of children.

4-ENGLISH

This zoom lens is a projection lens equipped with an EEPROM*1 and stepping motor.

*1 EEPROM: Electrically erasable programmable read-only memory

■Supported projectors

PT-RQ32K / PT-RZ31K / PT-RS30K / PT-RZ21K / PT-RS20K

Note

zSome of the alphabet letters at the end of projector model numbers may be omitted in this

manual.

zModels other than the above may also be supported. Refer to the operating instructions for

your projector or the Panasonic website (https://panasonic.net/cns/projector/).

zIf the projector you are using is PT-RQ32K / PT-RZ31K / PT-RS30K / PT-RZ21K /

PT-RS20K, you may not be able to use the projection lens depending on main version of

the rmware. If main version of the rmware is the version number shown below, update to

the latest rmware before use.

- PT-RQ32K / PT-RZ31K / PT-RS30K: Earlier than 3.00

- PT-RZ21K / PT-RS20K: Earlier than 2.00

For details on the update procedure, refer to the latest rmware information on the

Panasonic website (https://panasonic.net/cns/projector/pass/).

zThe main version of the rmware can be checked in the [STATUS] screen.

■Supplied Accessories

Make sure that the following has been provided.

Part name Appearance

Lens cover

1 each

(The product is

delivered with a lens

cover attached.)

Before Use

ENGLISH-5

Attaching the Lens

Attention

zBefore attaching the Projection Lens, remove the lens hole cover (only lens options mod-

els) and the two lens covers attached to the Projection Lens.

zIf the lens hole cover is already removed, start from step 3.

The illustrations in this procedure depict

use of the PT-RZ21K as an example.

1) Loosen the lens hole cover

screw.

zUse a Phillips screwdriver to turn the

lens hole cover screw counterclock-

wise until it is in its loosened state.

ねじ

レンズホールカバー

Lens hole cover

Screw

2) Remove the lens hole cover.

z(i) While pressing the lens release

button, turn the lens hole cover

counterclockwise until its marker ()

aligns with the marker on the projec-

tor (to the left of "LOCK"). (ii) Then

remove the lens hole cover.

レンズリリースボタン

Lens release button

Attaching the Lens / Detaching the Lens

Before replacing the projection lens

Return the projection lens to the home position before replacing or removing it.

For details on how to return the lens to the home position, refer to the operating instructions

of the projector.

Attention

zMake sure that the projector power supply is switched off before attaching or detaching the

projection lens.

zAfter removing the projection lens, store it safely away from vibration or impacts.

z Do not touch the electrical contacts of the projection lens with your ngers. Dust and dirt on

the contacts may cause contact malfunctions, while static electricity may damage the unit.

zDo not touch the surface of the lens with bare hands. Finger prints and dirt on the surface

of the lens will be magnied by the lens and lower the quality of the projected image. Place

the supplied lens cover on the zoom lens when the projector is not in use.

zThe lens is made of glass. The lens could be damaged if brought into contact with or

rubbed against hard objects. Handle the lens carefully.

zUse a clean, soft and dry cloth to wipe away dust and dirt from the projection lens.

Do not use uffy cloths containing oil, water or dust for cleaning. The lens is easily

damaged, so do not apply excessive pressure when wiping it.

6-ENGLISH

Attaching the Lens / Detaching the Lens (continued)

Attention

zTurn the projection lens counterclockwise, and verify that it is secure.

zStore the removed lens hole cover safely for future use.

zAfter attaching the projection lens, turn on the projector and perform lens calibration.

(page 8)

4) Use the lens drop prevention

screw supplied with the

projector to secure the

projection lens.

zUse a Phillips screwdriver to secure

the screw in hole A to the right of the

marker (orange) on the projection

lens.

目印（オレンジ色）

ねじ穴 A

レンズ落下防止ねじ

Marker (orange)

Screw

hole A

Lens drop prevention screw

3) (i) Insert the projection lens

while aligning its marker

(orange) with the marker on

the projector (to the left

of “LOCK”), and (ii) turn it

clockwise until it clicks into

place.

ENGLISH-7

Attaching the Lens / Detaching the Lens (continued)

Peripheral focus adjustment function

When using the projection lens, the focus balance between the center of the projected image

and the peripheral areas differs depending on the size of the image.

The projection lens is equipped with a function for adjusting the peripheral focus.

1) Operate the projector to align

the focus of the center of the

projected image.

2) Loosen the lock knob by

turning it counterclockwise.

Note

zThe screen sizes displayed on the lens are approximate guides.

3) Turn the peripheral focus

adjustment ring in the

directions of the arrows

to align the focus of the

peripheral areas of the image.

4) Tighten the lock knob by

turning it clockwise.

The illustrations in this procedure depict

use of the PT-RZ21K as an example.

■Adjusting the focus

ロックつまみ

周辺フォーカス調整リング

Peripheral focus adjustment ring

Lock knob

8-ENGLISH

Lens calibration

Perform lens calibration after attaching the lens.

1) Press the <MENU> button.

2) Use the ▲ and ▼ buttons to

select [PROJECTOR SETUP],

and press the <ENTER>

button.

zThe [PROJECTOR SETUP] screen

appears.

3) Use the ▲ and ▼ buttons to

select [LENS], and press the

<ENTER> button.

zThe [LENS] screen appears.

1/2

PROJECTOR SETUP

PROJECTOR ID ALL

PROJECTION METHOD

LENS

OPERATION SETTING NORMAL

LIGHT OUTPUT 100.0%

BRIGHTNESS CONTROL AUTO

STANDBY MODE NORMAL

NO SIGNAL SHUT-OFF DISABLE

NO SIGNAL LIGHTS-OUT DISABLE

INITIAL STARTUP LAST MEMORY

STARTUP INPUT SELECT LAST USED

DATE AND TIME

SUB MENU

MENU SELECT

ENTER

4) Use the ▲ and ▼ buttons to

select [LENS CALIBRATION],

and press the <ENTER>

button.

zThe [LENS CALIBRATION] screen

appears.

SUB MENU

MENU SELECT

ENTER

LENS

LENS TYPE ET-D3LEW10

LENS INFORMATION SETTING

LENS MEMORY

LENS HOME POSITION

ACTIVE FOCUS OPTIMIZER

LENS CALIBRATION

5) Use the ▲ and ▼ buttons to

select [SHIFT/FOCUS/ZOOM],

and press the <ENTER>

button.

zThe conrmation screen appears.

EXECUTE

MENU SELECT

ENTER

LENS CALIBRATION : ET-D3LEW10

SHIFT/FOCUS/ZOOM

SHIFT/FOCUS

ZOOM

6) Use the and buttons to

select [OK], and press the

<ENTER> button.

zLens calibration starts.

zThe projection lens moves to the

home position after adjustment range

calibration is complete.

LENS CALIBRATION : ET-D3LEW10

Proceed LENS CALIBRATION,

and return to HOME POSITION.

EXECUTE

CHANGE

ENTER

CANCEL

Note

zIf lens calibration is not performed, the available zoom range will be narrowed.

Attaching the Lens / Detaching the Lens (continued)

ENGLISH-9

Attention

zStore the removed projection lens safely without subjecting it to vibration or impact.

zStore the removed lens drop prevention screw safely for future use.

The illustrations in this procedure depict

use of the PT-RZ21K as an example.

1) Remove the lens drop

prevention screw.

zUse a Phillips screwdriver to remove

the screw in rst hole to the right of

the marker (orange) on the projection

lens.

2) (i) While pressing the lens release

button, (ii) turn the projection

lens counterclockwise, and (iii)

remove it.

zTurn the projection lens counterclock-

wise until its marker (orange) aligns

with the marker on the projector (

to the left of "LOCK").

zIf you intend to transport or store the

projector, proceed to step 3.

レンズリリースボタン

目印（オレンジ色）

レンズ落下防止ねじ

Lens drop prevention screw

Marker (orange)

Lens release button

Removing the Lens

3) Attach the lens hole cover

supplied with the projector.

z(i) Insert the lens hole cover while

aligning its marker () with the

marker on the projector (to the left

of "LOCK"), and (ii) turn it clockwise

until it clicks into place.

レンズホールカバー

Lens hole cover

4) Secure the lens hole cover.

zUse a Phillips screwdriver to tighten

the lens hole cover screw.

ねじ

Attaching the Lens / Detaching the Lens (continued)

Screw

10-ENGLISH

Projection relationships

The dimensional relationship between the screen and the projector is shown below.

■Dimensional relationship diagram

Note

zThis diagram assumes that the size and position of the projected image will be adjusted so

that the image lls the entire screen.

zThis illustration is not drawn to scale.

L Projection distance

LW Minimum distance

LT Maximum distance

L1 Lens protrusion dimension

SH Projected image height

SW Projected image width

SD Projected image size

zDimension for L1 (approximate values) (Unit: m)

Projector model Dimension for L1 (approximate value)

PT-RQ32K / PT-RZ31K / PT-RS30K 0.18

PT-RZ21K / PT-RS20K 0.21

Note

zThe illustrations of projectors in this manual are for informational purposes only and do not

represent a specic projector model. Congurations may vary with the model.

Attention

zTo prevent obstruction of the intake and exhaust vents, install the projector with a

clearance at least 500 mm (1 ft. 7 in.) from walls and objects.

If you are installing the projector in a sealed space, be sure to provide additional air

conditioning equipment and ventilation equipment. Insufcient ventilation will result in an

accumulation of heat and may activate the projector's protection circuit.

zAvoid setting up in places which are subject to sudden temperature changes, such as near

an air conditioner or lighting equipment (studio lamps, etc.).

■Dimensional relationship

For details on the projection distance (L), refer to “Projected image size and Projection

distance” and “Projection distance formulas” in the Appendix.

L (LW/LT)

SW SH

投写画面

スクリーン

Projected image

Screen

Tabla de contenidos

Otros manuales de Lente de la cámara de Panasonic

Panasonic

Panasonic Lumix G II H-H020AK Manual de usuario

Panasonic

Panasonic WV-LZ14 Manual de usuario

Panasonic

Panasonic Lumix H-H020 Manual de usuario

Panasonic

Panasonic H-FS12032K Manual de usuario

Panasonic

Panasonic H-HS030PP Manual de usuario

Panasonic

Panasonic L-X025 - Leica D Summilux Lens Manual de usuario

Panasonic

Panasonic H-FS12060 Manual de usuario

Panasonic

Panasonic WV-LZ6 Manual de usuario

Panasonic

Panasonic LUMIX S PRO 70-200 mm F4 O.I.S. Manual de usuario

Panasonic

Panasonic Lumix H-XA025 Manual de usuario

Panasonic

Panasonic DMW-GTC1 Manual de usuario

Panasonic

Panasonic Lumix H-FSA14140 Manual de usuario

Panasonic

Panasonic AWE800 - COLOR CAMERA Manual de usuario

Panasonic

Panasonic Lumix H-H020A Manual de usuario

Panasonic

Panasonic 12-60mm f/3.5-5.6 Manual de usuario

Panasonic

Panasonic HFS1442A Manual de usuario

Panasonic

Panasonic Lumix H-VS014140 Manual de usuario

Panasonic

Panasonic ET-ELW30 Manual de usuario

Panasonic

Panasonic ET-D75LE30 Manual de usuario

Panasonic

Panasonic LUMIX H-H014AK Manual de usuario

Panasonic

Panasonic S-R1635 Manual de usuario

Panasonic

Panasonic 5025232898695 Manual de usuario

Panasonic

Panasonic WV-LZ62 Manual de usuario

Panasonic

Panasonic Lumix H-FT012 Manual de usuario

Manuales populares de Lente de la cámara de otras marcas

THORLABS

THORLABS ELL15 Manual de usuario

FUJICA

FUJICA ZC1000 Manual de usuario

Tamron

Tamron A09 Manual

Sony

Sony SEL-55210 Manual de usuario

Sony

Sony VCL-HG2037 Manual de usuario

Honeywell

Honeywell HLM25V6F12 Manual de usuario

Sony

Sony VCL-ST30 Manual de usuario

Canon

Canon FD 35 - 70 mm Manual de usuario

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Manual de usuario

ARRI

ARRI Lenses Manual de usuario

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Manual de usuario

Rokinon

Rokinon DS50M-C Manual de usuario

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Manual de usuario

Sony

Sony VCL-DE07T Manual de usuario

Canon

Canon FD Lens Manual

Tamron

Tamron A036 Manual de usuario

Samsung

Samsung 20-50mm F3.5-5.6 ED II Manual de usuario

Tamron

Tamron 272E Manual de usuario