Panasonic ECONAVI CZ-CENSC1 Manual de usuario

3-39

Control of VRF SYSTEMS

2-2. Installation Instructions

Installation Instructions

ECONAVI Sensor

Model No. CZ-CENSC1

F616629

ENGLISH 3 ~ 17

Read through the Installation Instructions before you proceed

with the installation. In particular, you will need to read under the

“Safety Precautions”on EN 4.

FRANÇAIS 18 ~ 34

Lisez les instructions d'installation avant de commencer

l'installation. En particulier, vous devez lire la section « Consignes

de sécurité » en page 19.

ESPAÑOL 35 ~ 51

Lea las Instrucciones de instalacion antes de proceder con la

instalacion del equipo. En concreto, deberá leer detenidamente la

sección “Precauciones de seguridad” situada en la página 36.

DEUTSCH 52 ~ 70

Lesen Sie die Einbauanleitung, bevor Sie mit der Installation

beginnen. Insbesondere müssen die „Sicherheitsvorkehrungen“

auf Seite 53 gründlich durchgelesen werden.

ITALIANO 71 ~ 87

Leggere le Istruzioni di installazione prima di procedere con

l'installazione. Prestare particolare attenzione alla sezione

“Precauzioni di Sicurezza” a pagina 72.

PORTUGUÊS 88 ~ 104

Leia cuidadosamente as instruções de instalação antes de

prosseguir com a instalação. Em particular, é necessário ler as

informações na secção “Precauções de segurança” na página 89.

EȁȁǾȃǿȀǱ 105 ~ 122

ǻȚĮȕȐıĲİ ĲȚȢ ȅįȘȖȓİȢ İȖțĮĲȐıĲĮıȘȢ ʌȡȚȞ ıȣȞİȤȓıİĲİ ȝİ ĲȘȞ

İȖțĮĲȐıĲĮıȘ. ȈȣȖțİțȡȚȝȑȞĮ, șĮ ȤȡİȚĮıĲİȓ ȞĮ įȚĮȕȐıİĲİ ĲȘȞ

İȞȩĲȘĲĮ “ȆȡȠĳȣȜȐȟİȚȢ ǹıĳĮȜİȓĮȢ” ıĲȘ ıİȜȓįĮ 16.

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 39 17/03/09 11:02:45

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-40

Control of VRF SYSTEMS

EN 3

Contents

Supplied accessories & Parts Name ................................................3

Safety Precautions ...........................................................................4

Installation Precautions ....................................................................6

Mounting...........................................................................................9

Settings (For CZ-RTC3) .................................................................12

Test operation (For CZ-RTC3)........................................................15

Self-diagnostics (For CZ-RTC3).....................................................17

Speci¿cations .................................................................................17

Supplied accessories

Screw

M4 × 15.5

(2)

Clamper

(1)

NOTICE Remote control wiring is not supplied accessory.

( ¿eld supply )

Parts Name

Sensor

Detects human

motion within the

area

EN 4

Safety Precautions

Read before installation

Read the Installation Instructions carefully to install the unit

correctly and safely.

Be sure to read the Safety Precautions in particular before installation.

After the installation is complete, perform test operation to con¿rm

that no abnormality is present.

We assume no responsibility for accidents or damages resulting from

methods other than those described in the installation instructions

or methods not using speci¿ed parts. Malfunctions that occur due to

unauthorised installation methods are not covered by the product

warranty.

Read the installation instructions supplied with indoor units as well.

WARNING This symbol refers to a hazard or unsafe

practice which can result in severe

personal injury or death.

CAUTION This symbol refers to a hazard or unsafe

practice which can result in personal injury

or product or property damage.

Matters to be observed Prohibited matters

WARNING

Turn off the circuit breaker of the units before installation.

Ask your dealer or a professional for installation and electric work.

This sensor unit shall be installed in accordance with National

Wiring Regulations.

Securely connect and ¿[ the speci¿ed cables for wiring.

Do not allow the connection to be e[posed to the e[ternal force

of the cables.

Choose an installation location that suf¿ciently supports the

weight of the sensor unit.

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 40 17/03/09 11:02:45

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-41

Control of VRF SYSTEMS

EN 5

CAUTION

Do not use at the following locations.

Locations where condensation occurs

Locations where Àammable gases, etc. may leak

Locations where corrosive gases, etc. may leak

Locations with lots of water or oil droplets (including machine oil)

Locations where voltage Àuctuation frequently occurs

Locations where there is a machine producing

electromagnetic radiation

Locations where droplets of organic solvents spread

Locations where acidic or alkaline solutions or special sprays

are frequently used

Do not operate with wet hands.

Do not wash with water.

Do not install in places shown below.

In places with sharp temperature Àuctuations such as near

or facing air conditioner vents or appliances that generate

intense heat.

In places e[posed to direct strong light such as lightning or

headlights.

In places near incandescent lighting ¿[tures.

In places with swaying items like curtains.

In places with light partitions or other light shaders.

Please wipe the dirt on the sensor with a dry cloth.

The motion of people on the opposite side of the glass is

usually not detected.

Appro[imately 9seconds is needed until the motion sensor is

activated after the power is on.

EN 6

Installation Precautions

Dimensions

Installation location

Guideline for detection area

12 20

120

18.3

4.4

34.5

83.5 18.2

4.4

9.4

5.4

Install horizontally

against the surface.

Install vertically

against the oor.

90 degrees

Wall

Floor

Install at the height of

2.5 m (within 0.25 m)

above oor.

90 degrees

Floor

The sensor is unable to detect the

presence of humans within about

1 m from the wall.

Dead Zone

Appro . 1 m

Appro . 6 m

Appro . 10 m

Detection area

Dead Zone Appro . 1 m Appro . 6 m

1 m above oor

Appro . 2.5 m

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 41 17/03/09 11:02:47

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-42

Control of VRF SYSTEMS

EN 7

Wiring for the sensor unit

- Wiring diagram

- Type of wiring

8se cables of 0.5 to 1.25 mm2.

- Total wire length: 500 m or less

(The wire length between indoor units should be 200 m or less.)

- Number of connectable units

Remote controller, wireless receiver and sensor Ma[. 2

Indoor unitMa[. 8

For the RC wiring of ¿eld supply, please use insulated wires with

sheath. The insulation thickness should be at least 1 mm.

Regulations on wire diameters differ from locality to locality. For ¿eld

wiring rules, please refer to your LOCAL ELECTRICAL CODES

before beginning.

You must ensure that installation complies with all relevant rules and

regulations.

Indoor unit

Terminals for RC wiring Sensor unit

RC wiring (¿eld supply)

No polarity Wired RC

CZ-RTC3

(or other controller

which support ECONAVI

function.)

EN 8

Attention

Be careful not to connect cables to other terminals of indoor units

(e.g. power source wiring terminal). Malfunction may occur.

Do not bundle together with the power source wiring or store in the

same metal tube. Operation error may occur.

If noise is induced to the unit power supply, attach a noise ¿lter.

Using 1 indoor unit

Using more than 1 indoor unit or heat exchange ventilation unit

Note

Remote controller, wireless receiver and sensor can be connected

to any indoor unit for operation.

*Wiring as shown below is prohibited.

12 12

R1 R2

Wired RC Sensor unit

Indoor unit

12 12

R1 R2 R1 R2 R1 R2 R1 R2

Wired RC Sensor unit

Indoor unit Indoor unit Indoor unit Indoor unit

R1 R2 R1 R2 R1 R2

12 12

Wired RC Sensor unit

Indoor unit Indoor unit Indoor unit

RC wiring

Sensor unit

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 42 17/03/09 11:02:47

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-43

Control of VRF SYSTEMS

EN 9

Mounting

1. Remove the bottom case.

Bottom case

Flat-blade

screwdriver

Insert the driver

and slightly turn. *Please be well noted that

the claw may be broken if the

screw driver goes too deep.

2. Mount to the wall.

Attention

Mounting the bottom case

Tighten the screws securely until the screw heads

touch the bottom case. (Otherwise, loose screw

heads may hit the PCB and cause malfunction

when mounting the top case.)

Do not over-tighten the screws.

(The bottom case may be deformed, resulting in

fall of the unit.)

Connecting the remote control wiring

Arrange the wires as shown in the illustration for

2.1 in step , avoiding unnecessary wires being

stored in the case. (Caught wires may destroy the

PCB.)

Avoid wires touching parts on the PCB. (Caught

wires may destroy the PCB.)

EN 10

2.1 Exposed type

Preparation:

Make 2 holes for screws using a Phillips-head screwdriver.

Cut here with

a nipper and

remove the

burr with

a ¿le.

Claw (2 places)

Claw

Hole for screw

Screw (supplied)

Connect the remote control wiring.

Arrange the wires along the groove of the case.

Wall to ¿[ the receiver

Mount the bottom case

to the wall.

Mount the top case.

Align the claws of

the top case and

then align the claws

of the bottom case.

Top case

(Back side)

Remove the coating. Appro[. 6 mm

Remove the sheath. Appro[. 150 mm

Make sure the wiring connection is in

the correct direction.

Pass through

the hole.

Clamper

(supplied)

Bottom case (Back side)

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 43 17/03/09 11:02:50

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-44

Control of VRF SYSTEMS

EN 11

2.2 Embedded type

Preparation:

Make 2 holes for screws using a Phillips-head screwdriver.

Avoid the wire

being caught.

Claw (2 places)

Claw

Connect the remote control wiring.

Screw (supplied)

Hole for screw

Mount the top case.

Align the claws of

the top case and

then align the claws

of the bottom case.

Mount the bottom case to the wall.

Pass the wire through the hole in the

centre of the bottom case.

Terminal board

Bottom case (Back side)

Remove the coating.

Appro[. 6 mm

Make sure the wiring connection

is in the correct direction.

Top case

(Back side)

EN 12

Settings (For CZ-RTC3)

RC. setting mode (ECONAVI activation for remote controller)

1. Press and hold the 3 buttons for 4 seconds or more simultaneously.

2. Select the item to set. (Select [3. RC. setting mode].)

3. Set. (Select the Code no. and Set data.)

(Repeat)

Code

no. Set Item Set data

ECONAVI

activation

for remote

controller

Set the Set

data to 0001

to activate

ECONAVI.

0000Inactive (factory setting)

0001Activate

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 44 17/03/09 11:02:52

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-45

Control of VRF SYSTEMS

EN 13

Detailed settings (ECONAVI activation for indoor unit, Absence

mode setting, Start time of Absence mode)

1. Repeat steps 1 to 2 of RC. setting mode.

(Select [8.Detailed settings].)

2. Set. (Select the Unit no., Code no. and Set data.)

(Repeat)

Code

no. Set Item Set data

ECONAVI

activation

for indoor

unit

Set the Set

data to 0001

to activate

ECONAVI.

(If Code no.

E0 cannot be

selected, the

indoor unit does

not support

the ECONAVI

function.)

0000Inactive

0001Activate

Absence

mode

setting

Select the

Energy saving

mode that

operates in

human absence.

0000Do nothing.

0001Thermo off (factory

setting)

0002Unit suspended

(Cannot reactivate)

0003Unit suspended

(Can reactivate)

Start time

of Absence

mode

Set the timing

for switching to

Absence mode.

0001 - 0024 [hour]

(0003factory setting)

EN 14

ECONAVI info. (ECONAVI function ON/OFF, Absence mode setting,

Start time of Absence mode)

*This menu will not appear unless ECONAVI is enabled by setting

Code no. 34 to 0001 in RC. setting mode.

1. Repeat steps 1 to 2 of RC. setting mode.

(Select [0.ECONAVI info.].)

2. Select [Setting info.].

3. Set. (Select the Code no. and Set data.)

(Repeat)

Code

no. Set Item Set data

ECONAVI

function

ON/OFF

Set the ECONAVI function

ON or OFF. (This can also

be done via the normal

menu.)

0000OFF

0001ON

Absence

mode

setting

Same as Code no. E1 in the Detailed settings.

Start time

of Absence

mode

Same as Code no. E5 in the Detailed settings.

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 45 17/03/09 11:02:52

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-46

Control of VRF SYSTEMS

EN 15

Test operation (For CZ-RTC3)

Preparation: Turn on the circuit breaker of units and then turn

the power on. After the power is turned on, ECONAVI sensor unit

operation is ignored for appro[. 90 seconds because settings are

being made. This is not malfunction.

1. Press and hold the 3 buttons for 4 seconds or more simultaneously.

2. Select [0.ECONAVI info.].

3. Select [Sensor unit info.].

4. Con¿rm the data set for Code no. 11 and 12 of Unit no.1.

EN 16

Code

no.

Data shows the state of the sensor unit.

0000not connected

0001normal state

0002initial state

0003duplication of the sensor unit

0004error state

* If 0000 is displayed, the system can not ¿nd the sensor unit.

* If 0001 is displayed, the sensor can detect human motion.

* If 0002 is displayed, the sensor is initializing. It takes about

90 seconds for the sensor to complete initialization after the

power is on.

* If 0003 is displayed, multiple sensor units are connected.

The system supports only 1 sensor unit per indoor group.

* If 0004 is displayed, the sensor is broken down.

* Data is updated automatically every 30 seconds.

12 In 30 seconds, the number of times human motion was

detected. * Data is updated automatically every 30 seconds.

Check that the sensor will detect human motion.(active)

Step 1 Ensure that Code no. 11 displays 0001.

Step 2 Wave your hand in front of the sensor for 1 minute.

Step 3 Check that Code no. 12 displays 1 or more.

Check that the sensor will not detect human motion.(inactive)

Step 1 Ensure that Code no. 11 displays 0001.

Step 2 Cover the sensor with a bo[¿rmly so that the sensor will not

detect human motion.

Step 3 Wait for 1 minute.

Step 4 Check that Code no.12 displays 0.

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 46 17/03/09 11:02:52

AMP Air Conditioning

www.ampair.co.uk | [email protected]

3-47

Control of VRF SYSTEMS

EN 17

Self-diagnostics (For CZ-RTC3)

If the remote control screen displays a Àashing ECONAVI, refer

to the following information.

Reboot the

sensor unit.

( For example,

disconnect

the sensor

unit from the

wiring, and

reconnect it.)

If there is no Àashing ECONAVI:

The sensor unit can be used normally.

If the Àashing ECONAVI disappears for a while,

but appears again soon:

The sensor unit is broken down.

If the ECONAVI Àashes continually:

The wiring of the sensor unit may be faulty.

The sensor unit may be broken down.

Speci¿cations

Model No. CZ-CENSC1

Dimensions (H) 120 mm × (W) 70 mm × (D) 32 mm

Weight 75 g

Temperature/

Humidity range

0C to 40C/20to 80( No condensation )

* Indoor use only.

Power Source DC16 V (Supplied from indoor unit)

Connections 1 sensor per indoor group

NOTICE The English te[t is the original instructions. Other

languages are translations of the original instructions.

Printed in China

T0902-1

2. ECONAVI Sensor (CZ-CENSC1)

TD831193-00 VRF SYS INDOOR.indb 47 17/03/09 11:02:52

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Otros manuales para ECONAVI CZ-CENSC1

Tabla de contenidos

Otros manuales de Accesorios de Panasonic

Panasonic

Panasonic MAZ9xxxH Series Manual de usuario

Panasonic

Panasonic SR-CN108 Manual de usuario

Panasonic

Panasonic FX-301-F7 Manual de usuario

Panasonic

Panasonic MA2S7840G Manual de usuario

Panasonic

Panasonic Schottky Barrier Diodes MA3SE020G Manual de usuario

Panasonic

Panasonic MA3D750 Manual de usuario

Panasonic

Panasonic HG-C Series Manual de usuario

Panasonic

Panasonic MA2Z784 (MA784) Manual de usuario

Panasonic

Panasonic UE-608040 Manual de usuario

Panasonic

Panasonic MA2SP02 Manual de usuario

Panasonic

Panasonic LS-400 Series Manual de usuario

Panasonic

Panasonic MALS068 Manual de usuario

Panasonic

Panasonic MA22D39 Manual de usuario

Panasonic

Panasonic PM-25 Series Manual de usuario

Panasonic

Panasonic Infrared Light Emitting Diodes LN77L Manual de usuario

Panasonic

Panasonic MA2YF80 Manual de usuario

Panasonic

Panasonic MCO-230AIC Manual de usuario

Panasonic

Panasonic CX-400 Series Manual de usuario

Panasonic

Panasonic KX-HNS103AZ Manual de usuario

Panasonic

Panasonic MA2DF31 Manual de usuario

Panasonic

Panasonic MA3J142A Manual de usuario

Panasonic

Panasonic MA2J7290G Manual de usuario

Panasonic

Panasonic CX-400 Series Manual de usuario

Panasonic

Panasonic NN-SE9**S Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario