P2 Wireless Technologies Z100 Manual de usuario
mn
WIRELESS ACCESS POINT
USER MANUAL
Z100
P2 Wireless Technologies Limited
© 2015 All rights reserved
Page 1of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
Contents
About This Guide ............................................................................................................................................2
Product Overview ...........................................................................................................................................2
Safety Instructions ..........................................................................................................................................3
Package Contents............................................................................................................................................4
Possible Configurations...................................................................................................................................5
Explanation of Ports....................................................................................................................................5
Installation Procedure.................................................................................................................................6
Installation Environment ........................................................................................................................6
Wall Mounting Procedure.......................................................................................................................6
Ceiling Mounting Procedure...................................................................................................................6
LED Indications................................................................................................................................................8
SmartMoment—Configuring the AP...............................................................................................................9
Connection Procedure ................................................................................................................................9
Wireless Method.....................................................................................................................................9
Wired Method ........................................................................................................................................9
Default Login Information.......................................................................................................................9
Note ............................................................................................................................................................9
Configuring and Monitoring the Access Point ..............................................................................................10
Proper Disposal of Product ...........................................................................................................................11
Waste of Electrical and Electronic Equipment..........................................................................................11
European Union RoHS...............................................................................................................................11
China RoHS................................................................................................................................................11
Safety and Regulatory Compliance...............................................................................................................12
Basic Troubleshooting...................................................................................................................................13
Page 2of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
About This Guide
This guide explains how to set up the access point Z100 for WLAN access in a general network deployment,
and the various LED status indication.
Product Overview
The Z100 is a dual-band 2x2 MIMO 802.11ac indoor Wi-Fi AP, designed for high-density deployments in
large offices, schools, hospitals and hotels that require premium performance. It can provide up to
1167Mbps aggregated data rates. With the enhanced transmission power and receive sensitivity, the AP
promises high throughput and reliable coverage that is essential for the modern network, catering for the
needs of the versatile business landscapes nowadays.
To meet the demand for the high user density in these scenarios, the Z100 is equipped with our very own
DensityBoost technology to significantly increase the per-AP user density. And in addition to efficient
network management, access policy implementation is made easy by the flexibility of employing multiple
SSIDs to control user access to the network, particularly useful for office environment or retailers who need
to separate staff and guest use for security reason.
Page 3of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
Safety Instructions
1. Read these safety instructions carefully before installation or usage.
2. Keep this user manual for later reference.
3. Disconnect the access point from the power source before cleaning. Use a damp cloth for
cleaning. Do not use liquid or spray detergents.
4. To avoid risk of injury from electrical shock or energy hazard, installation and service of this
product must be performed by qualified service personnel.
5. Install the access point on a reliable surface. Poor installation may cause it to fall onto people or
equipment and make body injury and equipment damage.
6. Do not install the access point near the power line, electric lamp, power grid, or in any forceful
power grid place.
7. To acquire steady power, connect the PoE port with a network cable under 50m. The network
cable compiles with the DC resistance definition in the YD/926.2 protocol.
8. Make sure the voltage of the power source is correct before connecting the access point to the
power outlet.
9. Use a steady power source to ensure normal functioning.
10. Ensure the power adapter is grounded well when installing the access point indoor.
11. The lightning protection module inside the device is basic. Install any additional protection if
necessary.
12. Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
13. All cautions and warnings on the device should be noted.
14. If the access point is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
15. Never open the access point. For safety reasons, the access point should be opened only by
qualified service personnel.
16. If one of the following situations arises, get the equipment checked by service personnel:
i. The power cord or plug is damaged.
ii. Liquid has penetrated into the access point.
iii. The access point does not work well, or you cannot get it to work according to the user's
manual.
iv. The access point has been dropped and damaged.
v. The access point has obvious signs of breakage.
17. DO NOT LEAVE THE ACCESS POINT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE
MAY GO BELOW 0°C OR ABOVE 45°C. THIS COULD DAMAGE THE ACCESS POINT.
Page 4of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
Package Contents
Access Point Z100 × 1
Drop Ceiling Mounting Kit × 1
Wall Mounting Kit × 1
Inform your supplier if there are any incorrect, missing, or damaged parts.
Page 5of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
Possible Configurations
Explanation of Ports
Ports & Connectors
Quantity and Specifications
1.
DC Jack
Range:
12 V DC 1A
2.
Ethernet Port
1 ×10/100/1000 Mbps Ethernet port
PoE input:
802.3af
3.
Console
A RJ-11 port. Connect the AP to a serial terminal or a laptop
for direct local management.
4.
Reset
Press the button longer than 5s to restore the AP to default
settings.
5.
USB
Up to 0.5A USB connection for future extension.
6.
Kensington Lock Slot
For added security using Kensington lock.
7.
Mounting Back
Fit with mounting components to install the AP to various
surfaces or locations. The two mounting types include drop
ceiling mount and wall mount.
Note:
━AP that is not set up according to the instructions in the user manual may malfunction.
━The connection quality of the AP and Wi-Fi coverage vary with the actual environment.
━Only use the mounting kits that is compatible with the AP.
━Please refer to the network plan provided. Without adhering to the network plan may
result in a network failure.
━For the best practice, please consult P2 authorized engineers.
1
2
3
4
5
6
7
Page 6of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
Installation Procedure
Installation Environment
Operating ambient temperature: 0°C-45°C
Operating ambient humidity: 5%-95% non-condensing
Wall Mounting Procedure
1. Drive two screws in the wall. The distance between two screws should be 40mm.
2. Align the bracket with screws.
3. Pull down the bracket until it is fastened tightly.
4. Align the securing hook of the AP with the bracket from up to down until it is locked securely.
Ceiling Mounting Procedure
1. Secure the ceiling bracket on the ceiling rail and adjust according to the size of the rail.
2. Fasten the bracket with the ceiling rail with a screw.
Page 7of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
3. Align the securing hook of the AP with the bracket (see dotted line), and slide the AP towards
the bracket until the AP is completely locked.
4. Use the cable-tie through the locking hole to lock the AP with the bracket.
Page 8of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
LED Indications
You may check on the LED on the front of the access point for its current status. The different status are
summarized in the table below:
LED
Function
State - Colour
Indication
RUN
AP power / ready
status
Steady –Green
AP is ready
Flashing –Green
AP is booting up
Red
AP hardware failure
Off
No power to AP
LAN
Network Link Status
Steady –Green
1000Mbps Ethernet link negotiated
Steady –Yellow
10/100Mbps Ethernet link negotiated
Flashing
Ethernet link activity
Off
Ethernet link unavailable
5G
5GHz Radio Status
Steady –Green
5GHz radio is enabled
Off
5GHz radio is disabled
2.4G
2.4GHz Radio Status
Steady –Green
2.4GHz radio is enabled
Off
2.4GHz radio is disabled
Page 9of 14
Copyright © 2015 P2 Wireless Technologies Limited. All rights reserved.
WIRELESS ACCESS POINT USER MANUAL
SmartMoment—Configuring the AP
The Z100 comes with the built-in SmartMoment for basic configuration of the AP. To configure the AP,
connect it through wireless or wired method.
Connection Procedure
Wireless Method
1. Power up the AP.
2. Use a Wi-Fi-enabled device to connect to the SSID “P2MTWifi” with password “p2mtuser”.
3. Open the browser and type the IP address “172.16.0.1”.
4. Navigate to the top menu bar and click Lightweight under Mode.
Wired Method
1. Power up the AP.
2. Connect the AP and the PC with a LAN cable.
3. Set the IP of the PC to “192.168.1.2”.
4. Navigate to SmartMoment by “192.168.1.1”.
5. Navigate to the top menu bar and click Lightweight under Mode.
Default Login Information
Username: p2mtadmin
Password: p2mtadmin
Note
SmartMoment Lightweight mode is for basic configuration ONLY. Use the advance mode for advanced
setting. For details, please refer to the SmartMoment User Guide.
Tabla de contenidos
