Overland Storage NEO 8000 Manual de usuario

Introduction

IMPORTANT: Overland Storage requires that all NEO 8000

parts be removed and replaced by an Overland Storage

authorized service provider. Improper installation may

result in damage which voids existing warranties.

This document describes how to remove and replace a

Signal Cable for a Horizontal Robotics Assembly (HRA)

installed in a NEO 8000 system from Overland Storage.

Unpacking the Spare

Carefully unpack the spare part and verify that you have

all the parts:

•HRA Master and Slave Signal Cables

•Remove & Replace/Add-On Instructions

Tools Needed

•Phillips screwdriver

•Hex screwdriver

WARNING: The GUI touch screen does not

completely shut off NEO 8000 system power. To

reduce the risk of electric shock or damage to

equipment, disconnect the power by unplugging

the power cords.

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent electrostatic

damage, observe the following precautions:

•Transport and store items in static-safe containers.

•Keep electrostatic-sensitive parts in their containers

until they arrive at static-free stations.

•Use a wrist strap and properly-grounded tools.

•Make sure you are always properly grounded when

touching a static-sensitive component or assembly.

•Keep the work area free of non-conductive materials.

•Avoid touching pins, leads, or circuitry.

Before beginning, be sure there is enough space on the

around the library system to allow access to the units.

NOTE: With the HRA installed, the right side of the Master unit

is connected to the left side of the Slave unit. While not

recommended, if it becomes necessary to detach the units, refer

to the NEO 8000 Scalability Upgrade Installation Guide (P/N

104370-1nn).

1. Power down the library, turning off the circuit

breakers and removing the power cords.

2. At the Slave unit, remove and retain the screws (six

hex or eight phillips) that secure the right side panel

and carefully remove the panel (Figure 1).

Figure 1. Right Panel Removal

NEO 8000 Library

Remove & Replace

Instructions

HRA Signal Cable Spare

Overview & Notes

NEO-8118

Preparing a Library for Installation

NEO-8090

3. At the Master unit, remove and retain the screws (six

hex or eight phillips) that secure the left side panel

and carefully remove the panel.

4. If additional access is needed, remove and retain these

access plates (Figure 2) from the rear of both

libraries:

• Master left-center access plate

• Master right-center access plate

•Slaveleft-centeraccess plate

• Slave right-center access plate

Figure 2. Remove These Plates for Additional Access

To provide access to the signal cables running along the

back sheet metal under the HRA, it is necessary to loosen

the HRA (Figure 3).

IMPORTANT: Follow electrostatic discharge (ESD)

protocols when removing and attaching the HRA

Controller card signal cables.

Figure 3. HRA Components and Connections

1. Remove and retain the four M4x10mm PH screws

holding the HRA to the mounting brackets.

2. Carefully lift and move the HRA up and toward the

front of the libraries, resting it on the mounting

brackets in front of the alignment pins (Figure 4).

Figure 4. Repositioning the HRA

CAUTION: Be careful not to damage the sensors mounted

on the brackets between the alignment pins (Figure 5).

Figure 5. HRA Mounting Bracket

NEO-8105

Access

MasterSlave

Access

Plates

HRA Cable Change-out

NEO-8097a

J7J8

J1J2

Mounting ScrewsHRA Controller PCB

Signal Cable Connections

NEO-8096

NEO-8099

Alignment Pins

Sensors

3. Locate the 48" long (122cm) Master Signal Cable

(P/N 969446-101) in the kit.

4. On the HRA Controller PWA, unplug the old Master

Signal Cable from the J4 connection (Figure 6).

5. Plug the new cable into the J4 socket.

6. Remove the old cable from the D-clamps along the

back sheet metal and run the loose end down to the

Master Primary Card Cage.

7. Insert the new cable into the D-clamps and run it

down to the Master Primary Card Cage.

8. Repeat Steps 4–7 for the 73" long (185cm) Slave

Signal Cable (P/N 969446-102), running it down to the

Slave Primary Card Cage.

Figure 6. HRA Controller PWA Connectors

Change out the HRA Master Signal Cable at the Master

Primary Card Cage assembly.

1. Remove and retain the screws holding the Primary

Card Cage assembly in the Master library (Figure 7):

•Three M3x10mm screws on the fan assembly (but

do not remove the fan assembly)

•Three M3x8mm screws on the card cage assembly

Figure 7. Location of Fan/Card Cage Assembly

2. Pull the fan/card cage out far enough to access the

connectors located on the back of the cage.

3. Disconnect the old cable from J8 on the Card Cage

PWA (Figure 8) and remove it from the library.

Figure 8. Master Signal Cable Connection

4. Locate the new Master Signal Cable and plug it into

the J8 socket.

5. Pull any excess cable down and position it behind the

card cage.

6. Push the fan/card cage back in place and refasten it

with the retained screws.

CAUTION: Be sure to use the 10mm for the fan assembly.

Using the shorter 8mm card cage screws may strip the

threads and prevent proper assembly.

Change out the HRA Slave Signal Cable at the Slave

Primary Card Cage assembly.

1. Remove and retain the screws holding the Primary

Card Cage assembly in the Slave library (Figure 7):

•Three M3x10mm screws on the fan assembly (but

do not remove the fan assembly)

•Three M3x8mm screws on the card cage assembly

J7 J8

J1 J2

NEO-8504

Slave Signal

Connection (J3)

Master Signal

Connection (J4)

Master Card Cage Cable Change-out

NEO-8033

NEO-8028

Fan Screws

Cage Screws

Cage Screw

NEO-8122

J2 J3 J4

J7 J8

J9 J10

J11 J12 J13

J14 J15

Master

Signal

Cable

Slave Card Cage Cable Change-out

2. Pull the fan/card cage out far enough to access the

connectors located on the back of the cage.

3. Disconnect the old cable from J7 on the Card Cage

PWA (Figure 9) and remove it from the library.

4. Locate the new Slave Signal Cable and plug it into the

J7 socket.

5. Pull any excess cable down and position it behind the

card cage.

6. Push the fan/card cage back in place and refasten it

with the retained screws.

CAUTION: Be sure to use the 10mm for the fan assembly.

Using the shorter 8mm card cage screws may strip the

threads and prevent proper assembly. Figure 9. Slave Signal Cable Connection

NOTE: If you detached the libraries, refer to the NEO 8000

Scalability Upgrade Installation Guide (P/N 104370-1nn) for

information about reconnecting and leveling the units.

1. Guide the HRA onto the alignment pins on the two

Mounting Bracket assemblies.

CAUTION: Be careful not to damage the sensors mounted

on the brackets between the alignment pins (Figure 5).

2. Loosely secure the HRA with one M4x10mm PH screw

to each Mounting Bracket assembly.

3. Using the drive belt, operate the shuttle by hand

the full length of the HRA to ensure that there are no

obstructions that interfere with its travel.

4. With the shuttle positioned in the middle of the HRA,

tighten the two installed screws and screw in the

remaining two retained screws (Figure 3).

5. Reattach the power cords and turn on both circuit

breakers to power up the library.

6. After POST completes, run Menu > Diagnostics >

Cartridge Cycle to verify the operation of the library.

NOTE: This test will randomly move cartridges in the library

and may require the host software to reinventory it.

7. Using the retained screws (six hex or eight Phillips),

secure the right side panel to the Slave library.

8. Using the retained screws (six hex or eight Phillips),

secure the left side panel to the Master library.

9. If any rear access panels were removed, replace them

using the retained screws.

All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained therein are

held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that no right is conveyed

to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any kind, either expressed or

implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the product(s) or program(s) described

in this document at any time. These changes will be incorporated in new editions of this publication.

Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.

NEO-8122

J2 J3 J4

J7 J8

J9 J10

J11 J12 J13

J14 J15

Slave

Signal

Cable

Reactivating the Library

Getting Help

You can get technical support on the Internet at

support.overlandstorage.com,

or call 1-877-654-3429 (toll-free U.S. & Canada)

or 858-571-5555x5 (International).

Otros manuales para NEO 8000

Tabla de contenidos

Otros manuales de Almacenamiento de Overland Storage

Overland Storage

Overland Storage ARCvault Series Manual de usuario

Overland Storage

Overland Storage SnapServerXSR 40 Manual de usuario

Overland Storage

Overland Storage PowerLoader Manual de usuario

Overland Storage

Overland Storage SnapServer XSD 40 Manual de usuario

Overland Storage

Overland Storage LTO-4 Manual de usuario

Overland Storage

Overland Storage SnapExpansion XSR Manual de usuario

Overland Storage

Overland Storage Neo Series 2000 Manual de usuario

Overland Storage

Overland Storage Tandberg Data RDX QuikStor Manual de usuario

Overland Storage

Overland Storage REO 1000 Manual de usuario

Overland Storage

Overland Storage ARCvault Series Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de usuario

Overland Storage

Overland Storage NEO 8000E Manual de usuario

Overland Storage

Overland Storage SnapServer XSD 40 Manual de usuario

Overland Storage

Overland Storage NEO XL Series Manual de usuario

Overland Storage

Overland Storage ARCvault 2U Series Manual de usuario

Overland Storage

Overland Storage REO Series Manual de usuario

Overland Storage

Overland Storage SnapScale X2 Node Manual de usuario

Overland Storage

Overland Storage NEO 200S Manual de usuario

Overland Storage

Overland Storage NEO 8000 Guía

Overland Storage

Overland Storage LoaderXpress Guía

Overland Storage

Overland Storage SnapServer DX2 Manual de usuario

Overland Storage

Overland Storage SnapSAN S2000 Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de usuario

Overland Storage

Overland Storage REO 4600 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario