OTIS GEN2 OI-7032 Manual de usuario

Model OI-7032

32-Channel

_____________________________________

Operation Manual

Revision 2.5w

_______________________________________________________________________________________

___________________________________________________________

Product Overview

The Otis Instruments, Inc. GenII OI-7032 (32-Channel) is a Hybrid onitor that supports up to 32

WireFree sensor units, and up to four 4-20mA input sensors (when only 28 channels are setup as

WireFree).

The OI-7032 is backward compatible with GenI WireFree sensor units, and also supports GenII Wirefree

sensor units (configurable).

For additional information regarding the OI-7032, see the A endices at the end of this o eration

manual.

Table of Contents

Product Overview.......................................................................................................................................2

Introduction................................................................................................................................................ 5

Warnings..................................................................................................................................................... 6

Complete System Diagrams...................................................................................................................... 7

Front Panel.........................................................................................................................................................................7

Internal Diagram................................................................................................................................................................8

Terminal Board...................................................................................................................................................................9

Touchscreen (Front).........................................................................................................................................................10

Touchscreen (Back)..........................................................................................................................................................10

C (Delta) Power Supply................................................................................................................................................. 11

Internal Diagram – s Wired from the Factory..............................................................................................................12

Internal Diagram – Completely Wired............................................................................................................................ 13

Wiring Con igurations.............................................................................................................................14

DC Power-in (24 Volts DC (nominal; 22-26 Volts DC))................................................................................................. 14

C Power Supply Connection..........................................................................................................................................17

Touchscreen Power Connection...................................................................................................................................... 19

Touchscreen Connection..................................................................................................................................................22

Memory Installation.........................................................................................................................................................25

Connecting Sensors..........................................................................................................................................................27

Connecting Sensor 1................................................................................................................................................... 27

Connecting Sensor 2................................................................................................................................................... 29

Connecting Sensor 3................................................................................................................................................... 31

Connecting Sensor 4................................................................................................................................................... 33

Relay Configurations....................................................................................................................................................... 35

Connecting Relay 1..................................................................................................................................................... 35

Connecting Relay 2..................................................................................................................................................... 37

Connecting Relay 3..................................................................................................................................................... 39

Connecting Relay 4..................................................................................................................................................... 41

Power On/O ............................................................................................................................................43

Basic Operation - Home Screen Navigation.......................................................................................... 44

Trend Chart...................................................................................................................................................................... 45

Real-Time Values..............................................................................................................................................................48

Time Since Last Calibration and Null.............................................................................................................................51

utoscroll On/Off............................................................................................................................................................. 53

Channel Configuration.................................................................................................................................................... 54

Set as Wired or WireFree (Channels 29-32 ONLY).................................................................................................57

Processing................................................................................................................................................................ 57

Relay Configuration.................................................................................................................................................58

Setting Radio Address (WireFree)........................................................................................................................... 59

Setting Scale (Wired)............................................................................................................................................... 60

Setting Sensor Location........................................................................................................................................... 61

Duplicate Settings ................................................................................................................................................... 62

Channel Off .............................................................................................................................................................64

Con iguration Menu Navigation.............................................................................................................65

Entering Configuration Menu.........................................................................................................................................66

View Monitor Serial #...................................................................................................................................................... 67

View Date Manufactured................................................................................................................................................. 67

Calibration Mode..............................................................................................................................................................68

Relay Tests........................................................................................................................................................................ 69

OI-7032 Restart................................................................................................................................................................ 70

VIEW Modbus Output Settings: ddress........................................................................................................................ 71

VIEW Modbus Output Settings: Baud Rate....................................................................................................................71

VIEW Radio Settings: Radio Timeout.............................................................................................................................72

VIEW Gen II Radio Settings: Network ID......................................................................................................................72

VIEW Gen II Radio Settings: Primary or Secondary Monitor...................................................................................... 73

VIEW OI-7032 Reset to Factory Default........................................................................................................................ 73

VIEW Relay Settings: Relays 1-4 (Failsafe)................................................................................................................... 74

VIEW Relay Settings: Fault Terminal.............................................................................................................................74

VIEW Relay Settings: Fault Relay ssign...................................................................................................................... 75

Con iguration Menu Modi ications (Second-Level Con iguration Menu).........................................76

MODIFY Modbus Output Settings: ddress...................................................................................................................77

MODIFY Modbus Output Settings: Baud Rate.............................................................................................................. 78

MODIFY Radio Settings: Radio Timeout....................................................................................................................... 78

MODIFY Gen II Radio Settings: Network ID................................................................................................................ 79

MODIFY Gen II Radio Settings: Primary or Secondary Monitor.................................................................................79

MODIFY OI-7032 Reset to Factory Default...................................................................................................................80

MODIFY Relay Settings: Relays 1-4 (Failsafe)..............................................................................................................80

MODIFY Relay Settings: Fault Terminal....................................................................................................................... 81

MODIFY Relay Settings: Fault Relay ssign.................................................................................................................81

Relay Indicator......................................................................................................................................... 82

Fault Indicator..........................................................................................................................................83

Fault Status...................................................................................................................................................................... 83

Channel On Without Wired Sensor Connected (Fault).......................................................................................... 84

F1: Check Sensor Cable............................................................................................................................................. 84

F4: Check Sensor Board.............................................................................................................................................85

Error Messages.........................................................................................................................................86

Double-Primary Error......................................................................................................................................................86

utoscroll Error............................................................................................................................................................... 87

APPENDIX A: So tware Installation..................................................................................................... 88

Installation................................................................................................................................................ 89

HMI Software...................................................................................................................................................................89

APPENDIX B: Reading USB Drive........................................................................................................93

USB Drive................................................................................................................................................. 94

Removing the USB Drive................................................................................................................................................. 94

Reading the USB Drive.................................................................................................................................................... 94

Opening the Datalog Files.......................................................................................................................................... 94

Opening the Easy Converter So tware..................................................................................................................... 94

Converting the Datalog File to an .xls (spreadsheet) File....................................................................................... 97

Viewing the Datalog File............................................................................................................................................ 97

When Finished Reading the USB Drive....................................................................................................................97

APPENDIX C: 4-20mA Loop Current Introduction............................................................................ 98

4-20m Current Loop Introduction................................................................................................................................ 99

Overview........................................................................................................................................................................... 99

Calculations......................................................................................................................................................................99

Measuring Current.........................................................................................................................................................100

Speci ications.......................................................................................................................................... 101

Introduction

This document is an Operation anual containing diagrams and step-by-step instruction for proper

operation of the Otis Instruments, Inc. GenII OI-7032. This document should be read before initial

operation of the product.

Should a question arise during the use of the product, this document will serve as a first reference for

consultation. If further questions arise, or if the device is not working properly, please contact the sales

representative of this product.

Warnings

•The OI-7032 should only be used in an environment that constantly remains between the range of

-20 to 122 degrees Fahrenheit. If the OI-7032 is at risk of being exposed to temperatures that are

outside the previously stated range, DO NOT install the device in that location. For applications

in areas with the potential of reaching extreme temperatures, Otis Instruments recommends using

the OI-7032 indoors only (in a temperature-controlled environment).

•Even when the Power switch is in the off position, the AC and DC terminals are still hot—

regardless of if the device is wired as DC.

•Wiring Configuration Warnings:

●Provide a clean and stable 24 Volts DC (nominal; 22-26 Volts DC) voltage. Failure to to do

so may cause the unit (and any wired sensors that are connected to the unit) to not operate

properly.

●Voltage spikes higher than 26 Volts may damage the unit.

●Solar Panel power (with battery backup): This options may be used to power the unit,

however, care must be taken to ensure the proper voltage and wattage is used.

NOTE: The size that the solar anel should be (10, 30, 50, or 100 watts, for exam le) de ends

on several factors, including: geogra hical area, line-of-sight access to the sun, number of

wired sensors connected, and weather conditions.

Please consult a solar panel manufacturer for specific details. Otis Instruments, Inc. may

also be contacted to provide guidance and recommendations.

Complete System Diagrams

The following diagrams should be consulted for identification of Panels, Boards, and any other system

component that may be referred to in this Operation anual.

Front Panel

Internal Diagram

Terminal Board

Touchscreen (Front)

Touchscreen (Back)

Tabla de contenidos

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario