Orion CMK-01 Manual de usuario

FLAT LCD DISPLAY MOUNT MODEL

INSTALLATION MANUAL

VISIT US AT WWW.ORIONIMAGES.COM

Orion Images Corporation

10820 Walker St.

Cypress, California 90630

Tel. 714-816-7000

Fax: 714-816-7014

Website: www.orionima

es.com

CMK Ceiling

CAUTION! The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precaution

before beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or proper

damage. Keep these installation instructions in an easily accessible location for future reference.

Indicates that the power plug is to be disconnected from

the power outlet.

Safety precautions must be taken at all times.

Warning and caution in general

WARNING!

The wall, floor or ceiling should be capable of supporting a weight of at least five (5) times the monitor’s weight. If it cannot, the wall, floor

ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered t

Failure to do so could result in serious personal injury.

CAUTION! The ceiling structure must be capable of supporting a maximum weight of 400 lbs. If not, the ceiling must be reinforced. Prop

installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result

serious personal injury.

CAUTION! Make sure to hold the plasma display, or projector, securely and remove it from the mount to make the height adjustment prior

loosening the adjustment screws. Do not remove the screws completely from the extension loosen all at once. Loosen, remove, adjust then r

tighten the screws. Failure to do so could result in injury and or damage to the plasma display or projector.

Step 1

Screw the CMK-01 coupling adapter to the adjustable suspension adapters or 1½" (NTP) Pipe. Secure the coupling with the M6 security screw

(supplied). Figure 1.

AST-2446 Adjustable Ceiling Adapter

Single Stud Installation

Step 2

Secure the ceiling plate to the ceiling structure (see WARNING).

Step 3

Use suitable hardware (commercially available) depending on your installation environment to secure the two (2) mounting points found on the ceiling

plate to the ceiling structure (Figure 2).

Step 4

Refer to ceiling adapter installation instructions.

This hardware is commercially

available and is not included in

the hardware pack.

RELOCATE ADJUSTMENT

SCREWS

HEIGHTADJUSTABLE

LOWER TUBE

CEILING STRUCTURE

(SEE WARNING)

ADJUSTMENT

SCREWS

UPPER TUBE

(COMMERCIALLY AVAILABLE)

SUITABLE HARDWARE

CABLE ACCESS

OPENING

Solid Structure Installation

Step 1

Secure the ceiling plate to the ceiling structure (see WARNING).

Step 2

Use suitable hardware (commercially available) depending on your installation environment to secure the four (4) mounting points found on the ceiling

plate to the ceiling structure (Figure 3).

Step 3

Refer to ceilin

ada

ter installation instructions.

This hardware is commercially

available and is not included in

the hardware pack.

VESA 100: Secure the VESA 75/100 mounting bracket to the VESA 75 Using the four M4 x 10 Phillip screws. Raise and secure your monitor to the

plate that has the VESA 100 now on you CMK-01 adapter and use the four (4) M4 x 10 (mm) Phillips screws (supplied) and a Phillips screwdriver. (Do

not use other tools other than a Phillips screwdriver to prevent damage to the monitor or mounting points).

CAUTION: Do not over tighten the screws to the monitor failure to do so could result on damaging the monitor or the mounting points. See figure 4.

(4) M4 x 10

Phillips

(4) M4 x 10mm

Phillips Flat Head screws

Adapter Plate

75 MM /

100 MM VESA

plate

TENSION ADJUSTMENTS

Thank you for choosing Orion

for your installation needs.

If you have any questions please contact Orion information is shown on the front

of this page.

VESA 75

M6 X 8mm Set

Screw

Tilt tension

Swivel tension

IN-CMK01.R2

LCD CEILING MOUNT

VESA 75 to VESA 100 front plate

NOTE: Only used for monitors that are

VESA 100

CMK-01 LCD CEILING MOUNT

Description Qty Size

Phillips screws 4M4 x 10

Security screw 1M6 x 12

HARDWARE

Features: Tilt mount allows of adjustments up and down of ±90° from center and

360° swivel and cable access. Comes with a combination plate of VESA 75 and

VESA 100 for optional mounting depending on monitor.

Lbs: 2

MOUNT OVERVIEW

Tabla de contenidos

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario