Q I G Quick Installation Guide
Quick Installation Guide
Version 1.0
Q I G
Cable Types and Specifications:
For pin assignments for different types of cables, please refer to the following
tables.
10/100 Base-T(X) RJ-45 port
Pin Number Assignment
1 TD+
2 TD-
3 RD+
4 Not used
5 Not used
6 RD-
7 Not used
8 Not used
Resetting
To restore the switch configurations back to the factory defaults, press the button for 5 seconds.Reset
1. Launch the Internet Explorer and type in IP address of the switch. The default static IP address is
192.168.10.1
Follow the steps to set up the card:
PRINTED ON RECYCLED PAPER
Cable Type Max. Length Connector
10Base-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100Base-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000Base-T Cat. 5/Cat 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45
123
4
5
Wiring
Po wer
Redun dan t Inpu t pow er Du al DC i npu ts. 12 ~48 VDC o n 6 pin t erm inal bloc k
Ph ysica l Chara cteri stic
En clos ure I P-3 0
Di mens ion ( W x D x H) 11 6.4m m W x 170 mm D x 15 4mm H ( 4.6 " W x 6.7 " D x 6.1 " H inc h.)
Weig ht (g )
Environ menta l
-4 0 to 85 C (-4 0 to 18 5 F )
o o
St ora ge Temperatu re
5% t o 95% N on- con dens ing
Op era ting H umi dity
RS -232
-4 0 to 75 oC (- 40 to 1 67oF)
Op era ting Temp era tur e
Te chnol ogy
St op Bit s
Da ta Bit s
1, 1 .5, 2
Tx D, Rx D, RTS, CTS, DTR , DSR , DCD, RI, GND
24 00 g
7, 8
Power C ons umpt ion (Typ .) 18 Wat ts
Ov erl oad cu rre nt pro tec tion Pr ese nt
Reverse po larity pr ote ctio n Pre sen t
Se rial Po rts
Co nnec tor Term inal B loc k x 1 (Po rt 1) , DB9 ma le x 1 (Port 2 )
Op era tion M ode
Se rial B aud Rate 1 10 bps t o 921 .6 Kbp s
Port 1 : RS -42 2/RS -48 5(2W /4W ), Whi ch ca n be con fig ured b y uti lity
Port 2 : RS -23 2/RS -42 2/RS -48 5(2W /4W ). Whi ch ca n be con fig ured b y uti lity
RS -422 T x- , Tx+, R x+, R x-, G ND
RS -485 4 w ire : Tx+, T x- , Rx+, R x-, GND
2 wi re: D+ , D-
Parit y odd , eve n, non e, ma rk, sp ace
Regulat ory App roval s
CE E MC (E N 550 24, E N 55032), F CC Part 1 5 B
EM C
EN 5 502 4 (IE C/E N 6100 0-4 -2 (E SD) , IEC /EN 6 100 0-4 -3 (RS), IE C/E N 610 00- 4-4 ( EFT) , IEC /EN 6 100 0-4 -5 (S urg e),
IE C/E N 610 00-4-6 (C S), I EC/ EN 61 000 -4- 8 (PF MF) , IEC/ EN6 100 0-4 -11 (DI P))
EM S
IE C60 068 -2-27
Sh ock
IE C60 068 -2-31
IE C60 068 -2-6
Vi bra tion
Fr ee Fall
Wa rrant y
5 ye ars
EN 609 50- 1
Sa fety
2. Log in with default user name and password (both are admin).
Serial Port Pin Definition
1 5
6 9
The device supports dual redundant power supplies, Power Supply1
(PWR1) and Power Supply 2 (PWR2). The connections for PWR1,
PWR2 and the RELAY are located on the terminal block.
PWR-1PWR-2
1A@24V
V2- V2+ V1- V1+
Fault
Power inputs
The two sets of relay contacts of the 6-pin terminal block connector are used to detect user-
configured events. The two wires attached to the fault contacts form an close circuit when a
user-configured event is triggered. If a user-configured event does not occur, the fault
circuit remains opened.
Relay contact
3.After logging in, you should see the following screen. For more information on configurations,
please refer to the user manual.
I N D U S T R I A L
M 2 M
G at e w ay
Industrial Cellular M2M Gateway
1000Base-T RJ-45 port
Pin Number Assignment
1BI_DA+
2BI_DA-
3BI_DB+
4BI_DC+
5BI_DC-
6BI_DB-
7BI_DD+
8BI_DD-
10/100 Base-T(X) MDI/MDI-X
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
Note: “+” and “-” signs represent the polarity of the wires that make up each
wire pair.
1000Base-T MDI/MDI-X
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Configurations
After installing the device, the green power LED should turn on. Please refer to the
following tablet for LED indication.
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground screws to the grounding surface prior to
connecting devices.
Grounding
PWR1/2 Green On Power is on and function normally
PoE Green On PoE enabled
Fault Amber On Faulty relay (power failure or port disconnected)
WAN Green On WLAN is activated (Strength: 1<30%, 2 >30% <60%, 3>75%)
Blinking Transmitting data
Storage Green Blinking Data access
R.M Green On Reserved
Ring Green On Reserved
SIM 1/2 Green On SIM card is activated
10/100/1000Base-T(X) Ethernet ports
LNK/ACT Green On Port is connected
Blinking Transmitting data
Speed Amber On Port running at 1000Mbps.
Off Port running at 100Mbps.
Serial ports
Rx Red On Port is receiving data
Tx Green On Port is transmitting data
An tenn a Con nect or
(S MA Fe mal e)
Ce llul ar St anda rd
Ba nd opt ion s
GS M / GPRS / E GPR S / EDGE / W CDM A / HSDPA / HS UPA /HS PA+ /LTE
Am eri ca (US )
LTE :
700/1700/2100MHz
UM TS/HSDPA/H SUPA/H SPA+/D C-H SPA+:
800/850/1900/2100MHz
GS M/GP RS/ EDGE :
850/900/1800/1900MHz
Eu rop e (EU)
LTE :
FD D:21 00( B1)/ 180 0(B3 )/2 600( B7) /900 (B8 )/80 0(B 20) MH z
TD D:TD D:2 600( B38 )/23 00( B40) /25 00(B 41) M Hz
UM TS/HSDPA/H SUPA/H SPA+/D C-H SPA+:
21 00(B 1)/ 900( B8) M Hz
GS M/GP RS/ EDGE :
90 0/85 0 MHz
10 /100 /10 00 Bas e-T( X) Po rts i n
RJ 45 Auto MDI /MDIX 4
Ph ysica l Ports
IG MG-P 83244GC+-D4G
Specifications
OR ing M2M M odel
Gi gabi t Com bo por t wit h
10 /100 /10 00Ba se-T (X) an d
10 0/10 00B ase-X SF P por ts
4
Ce llula r Inter face
MT BF
14 034 5.5 955 h rs
STEP 1: Insert the negative/positive wires into the V-/V+ terminals,
respectively.
To keep the DC wires from pulling loose, use a small flat-bladeSTEP 2:
screwdriver to tighten the wire-clamp screws on the front of the
terminal block connector.
SI M card s lot 2
2
Fault con tact
Relay Rel ay ou tpu t to ca rry c apa cit y of 1A a t 24V DC
EN 5 503 2, CI SPR 32, EN 6100 0-3 -2, E N 610 00- 3-3 ,FC C Par t 15 B cl ass A
EM I
ORing Industrial Networking Corp.
Copyright© 2019 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
Website: www.oringnet.com
E-mail: support@oringnet.com
IGMG-P83244GC+-D4G
IGMG-P83244GC+-D4G
