Origin Acoustics DSUB6 Manual de usuario
Installation Manual
DSUB6 Series
Director Collection
DSUB6F5, DSUB6F3
Table of Contents
Introduction 1
Specifications 2
What’s Included 3
Tools & Items 3
Wire Recommendation 3
Planning 4
About Speaker Wire 4
Installing the Enclosure 5
Installation before Drywall 6
Installation aer Drywall 6
Wire Routing 7
Installing the Wire 8
Connecting the Wire 8
Wiring: Separate Sub Amplifier & 2-Channel Amplifier 9
Painting the Grille 10
Installing the Grille 10
Troubleshooting 11
Technical Assistance 12
Warranty 13
Return Process 14
1
Thank you for purchasing the Director Subwoofer 6. At Origin Acoustics, we take
pride in providing you with a high quality product. All of Origin Acoustics’ speakers
are designed to have excellent sound quality, longevity, and a simple installation
process.
This instruction booklet covers the necessary information for a smooth installa-
tion, including: the tools you will need, step-by-step instructions for installation,
troubleshooting tips for any errors that may occur, and all warranty information.
If for any reason you experience problems or if you have installation questions
please call us at (844) 674-4461. Hours of operation are 8:00am to 5:00pm (Pacific
Time), Monday through Friday.
Introduction
2
Model DSUB6F5 DSUB6F3
Part Number DSUB6F500 DSUB6F300
Woofer Cone Polypropylene Polypropylene
Woofer
Diameter
6.5 (165mm) 6.5 (165mm)
Frequency
Response
33Hz - 100 kHz ± 3dB 33Hz - 100 kHz ± 3dB
Impedance 8 ohm 8 ohm
Power
Handling
100 Watts 100 Watts
Dimensions 7.9 x 11.8 x 18.9”
(200 x 300 x 480mm)
7.9 x 11.8 x 18.9”
(200 x 300 x 480mm)
Grille
Diameter
7” (178mm) 4.25” (108mm)
Cutout
Diameter
5.9 (150mm) 3.5” (89mm)
Mounting
Depth
7.9” (200mm) 7.9” (200mm)
Specifications
3
Bandpass Subwoofer Bracket & Trim Ring Grille
What’s Included
• Drywall Saw
• Speaker Wire
• Pencil
• Wire Stripper
• Measuring Tape
• Drill
• Drill Bit ⅛” (3mm)
• Stiff Wire
• Stud Finder
• Fish Tape
• Spray Paint
• Compressed Air
Tools & Items
The gauge of wire used can have an impact on the performance of your speakers.
Use a multi-stranded wiring designed for amplifier to speaker connections. Which
gauge to select depends on the length of wire to be used on any particular speak-
er. The longer your run is, the larger your wire size must be.
Wire Recommendation
Wire Length Wire Gauge
0 -100’ (0 - 30m) 16
50 - 150’ (15 - 45m) 14
Over 100’ (30m) 12
4
Will you be driving it with a 2-channel amplifier or a designated subwoofer am-
plifier? The 2-channel option works fine but the separate subwoofer amplifier will
allow you to adjust the subwoofer output to achieve the sub-to-satellite balance
you want regardless of subwoofer location or number of satellite speakers used.
If you opt for the separate subwoofer amplifier, you will need to run three paired
speaker wires to the speaker location.
Planning: Amplifier Wiring
Find a location for the subwoofer. Positioning it near the satellite speakers is visu-
ally and sonically advantageous; being close to walls, especially corners, is very
helpful when maximum loudness is important. Start with where you want the port
opening to be. Then determine where the enclosure needs to be placed to allow
the port tube to easily reach the desired port opening location. For the subwoofer
to fit, the joists need to be at least 14” apart.
Planning: Location
You will need a wire that has at least two conductors; one that can be identified
as the positive and the other as the negative. All two conductor wires have some
means of identifying which conductor is which, but at times this identification
may be subtle. It’s crucial that you keep track of which wire you use for positive
(+) and negative (-). Typically if the wires are colored red and black, the red wire
is used for positive and the black wire is used for negative, but sometimes other
About Speaker Wire
5
Hold the template to the joist that you
plan on attaching the subwoofer en-
closure to. Drill six holes through the
marked locations on the template us-
ing a 5/16” (8mm) drill bit. Face the en-
closure’s rubber damping pad towards
the joist and secure it in place with the
supplied lag screws and washers. We
recommend that one person holds the subwoofer in place while another tightens
the screws to secure the DSUB to the joist.
1. Installing the Enclosure
colors or patterns are used. You can choose whichever color of wire you want to
be positive and negative as long as you remain consistent throughout the install.
On both your amplifier and your speaker the connectors will be identified as red
for positive and black for negative. It is very important to look carefully at the
speaker wires and be certain that the same wire that is attached to the positive
connector in the amplifier is attached to the positive connector in the speaker.
Template
Screws (6)
Enclosure
6
Slip the trim ring through the hole in
the drywall and into the port open-
ing. You may need to rotate it slightly
to get it to seat into place. Using the
three supplied screws and a #1 phil-
lips screwdriver, fasten the trim ring to
the port opening so that it fits snugly
against the ceiling surface.
Use the 8 supplied screws to attach
the port tube to the enclosure. Test
the wired DSUB to see that it’s working
properly. If you are using 2 channels
of input, make sure to test both.
The Mini Port Bracket will serve as
your new construction bracket. You
can attach it directly to a joist or use
the supplied new construction wings to position it precisely where you want it.
3. Installation aer Drywall
2. Installation before Drywall
7
Plan how you’ll route the wire to the desired speaker location. There are several
methods for routing the wire, and you may need to combine several of them.
Wire Routing
One option is to li up the carpet and
route “tape wire” under the carpet.
Under the Carpet
The wire can be routed behind the
baseboard by cutting a groove out of
the back of the baseboard, or by buy-
ing special baseboard designed for
concealing wires.
Behind the Baseboard
When available, you can route the wire
through an attic or crawlspace.
Attic or Basement
When running wires through a wall, be
sure to avoid all obstacles such as AC
wiring, pipes, and ducts.
Through Walls
If these speakers are being installed in a new home during construction, the
installation process will be a bit dierent (although much simpler). For these
situations, it’s recommended you purchase a bracket. Instructions on how to
install the speakers are provided with the bracket, or can be found on our web-
site. Visit www.originacoustics.com for more information.
For New Construction
8
Strip ¼ to ½ inches (6 to 12 mm) of the
insulation o both ends of the wire. To
avoid stray strands, twist them at the
end. Connect the wire to the amplifier,
and make sure the wire connected to
the le speaker output will be routed
to the le speaker, right output to right
speaker, etc.
4. Installing the Wire
0.25 - 0.5”
(6 - 12mm)
Speaker
Wire
Insert the wires into the connectors,
making sure that the positive wire is
being attached to the red connec-
tion and the negative wire is being
attached to the black connection. If
the negative and positive wires are
switched, speaker performance will be
drastically impacted.
5. Connecting the Wire
Speaker
Wire
Connector
Otros manuales para DSUB6
2
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Oradores de Origin Acoustics
Origin Acoustics
Origin Acoustics PP50B Manual de usuario
Origin Acoustics
Origin Acoustics ThinFit TF 60 Series Manual de usuario
Origin Acoustics
Origin Acoustics CIW60 Series Manual de usuario
Origin Acoustics
Origin Acoustics C64 Manual de usuario
Origin Acoustics
Origin Acoustics PROFESSIONAL PP50 PROFESSIONAL PP60 Manual de usuario
Origin Acoustics
Origin Acoustics THINFIT COLLECTION TF37DT Manual de usuario
Origin Acoustics
Origin Acoustics D65EX Manual de usuario
Origin Acoustics
Origin Acoustics COMPOSER C69 Manual de usuario
Origin Acoustics
Origin Acoustics Director D100 Series Manual de usuario
Origin Acoustics
Origin Acoustics DIRECTOR D89 Manual de usuario
Origin Acoustics
Origin Acoustics D105EX Manual de usuario
Origin Acoustics
Origin Acoustics DIRECTOR D69 Manual de usuario
Origin Acoustics
Origin Acoustics DIRECTOR D103DT Manual de usuario
Origin Acoustics
Origin Acoustics Director 100 Series Manual de usuario
Origin Acoustics
Origin Acoustics Season Outdoor OS 60 Series Manual de usuario
Origin Acoustics
Origin Acoustics PROFESSIONAL PP50 PROFESSIONAL PP60 Manual de usuario
Origin Acoustics
Origin Acoustics thinfit tf34 Manual de usuario
Origin Acoustics
Origin Acoustics Seasons Outdoor Collection OSR85 Manual de usuario
Origin Acoustics
Origin Acoustics SEASONS LANDSCAPE LS64 Manual de usuario
Origin Acoustics
Origin Acoustics OUTDOOR OS80B Manual de usuario
