is registered trademark or trademark of Oriental Motor Co., Ltd., in Japan
and other countries.
© Copyright ORIENTAL MOTOR CO., LTD. 2015
Technical Support Tel:(800)468-3982
8:30 A.M. to 5:00 P.M., P.S.T. (M-F)
7:30 A.M. to 5:00 P.M., C.S.T. (M-F)
www.orientalmotor.com
Schiessstraße 74, 40549 Düsseldorf, Germany
Technical Support Tel:00 800/22 55 66 22
www.orientalmotor.de
Tel:01256-347090
www.oriental-motor.co.uk
Tel:01 47 86 97 50
www.orientalmotor.fr
Tel:02-93906346
www.orientalmotor.it
Tel:+55-11-3266-6018
www.orientalmotor.com.br
• Please contact your nearest Oriental Motor oce for further information.
4-8-1Higashiueno,Taito-ku,Tokyo 110-8536
Japan
Tel:03-6744-0361
www.orientalmotor.co.jp
Tel:0800-060708
www.orientalmotor.com.tw
Singapore
Tel:1800-8420280
www.orientalmotor.com.sg
Tel:1800-806161
www.orientalmotor.com.my
Korea
Tel:080-777-2042
www.inaom.co.kr
Tel:1800-888-881
www.orientalmotor.co.th
Tel:400-820-6516
www.orientalmotor.com.cn
Tel:+91-80-41125586
www.orientalmotor.co.in
Hong Kong Branch
Tel:+852-2427-9800
Introduction
zOverview of the product
The logic inversion module VCS03-3 is a circuit to invert the logic of signals connected.
Two signals can be connected to a single unit of the VCS03-3.
zHazardous substances
The products do not contain the substances exceeding the restriction values of RoHS
Directive (2011/65/EU).
Safety precautions
The precautions described below are intended to prevent danger or injury to the user
and other personnel through safe, correct use of the product. Use the product only after
carefully reading and fully understanding these instructions.
Handling the product without observing the instructions that accompany a "Warning"
symbol may result in serious injury or death.
yDo not use the product in explosive or corrosive environments, in the presence of
ammable gases, locations subjected to splashing water, or near combustibles. Doing
so may result in re or injury.
yAssign qualied personnel the task of installing, wiring, operating/controlling,
inspecting and troubleshooting the product. Failure to do so may result in re or
injury.
yInstall the VCS03-3 in an enclosure. Failure to do so may result in injury.
yConnect the product securely in accordance with the wire connection example. Failure
to do so may result in re.
yFor the power supply use a DC power supply with reinforced insulation on its primary
and secondary sides. Failure to do so may result in electric shock.
yDo not disassemble or modify the VCS03-3. Doing so may result in injury. Refer all
such internal inspections and repairs to the branch or sales oce from which you
purchased the product.
Handling the product without observing the instructions that accompany a "Caution"
symbol may result in injury or property damage.
yDo not use the VCS03-3 beyond its specications. Doing so may result in injury or
damage to equipment.
yTake measures against static electricity and electrical noise when using the VCS03-3.
Failure to do so may result in damage to equipment or malfunction.
yKeep the area around the VCS03-3 free of combustible materials. Failure to do so
may result in re or skin burn(s).
yWhen an abnormal condition has occurred, immediately stop operation and turn o
the power. Failure to do so may result in re or injury.
yTo dispose of the VCS03-3, disassemble it into parts and components as much as
possible and dispose of individual parts/components as industrial waste.
Preparation
zChecking the product
Verify that the items listed below are included. Report any missing or damaged items to
the branch or sales oce from which you purchased the product.
yLogic Inversion Module VCS03-3.............................. 1 unit
yOPERATING MANUAL (this document)...................... 1 copy
zSpecication
ypower supply voltage: 5 to 24 VDC±10%
yInput signals: Photocoupler inputs
Input-signal voltage (between terminals) 18.1 to 26.4 V *
Maximum response frequency 100 kHz (duty cycle is 50%)
yOutput signals: 30 VDC or less, 120 mA or less
Collector-emitter saturation voltage 0.5 V or less
* An electric current of up to 9.5 mA may ow. Note the specications of equipment
connected.
Connection
zTerminal (signal) name
Terminal (signal)
name Description Terminal (signal)
name Description
Vcc Power supply input
5 to 24 VDC
IN1+ 24 V Input 1
GND IN1−
OUT1 Output 1 IN2+ 24 V Input 2
GND IN2−
OUT2 Output 2
GND
zNotes about wiring
yApplicable lead wire for terminal block: AWG26 to 16 (0.14 to 1.5 mm2)
yConnecting signals: The signal is output via the same number that has been input.
Using shielded cables and the like, keep the signal lines away
from power lines, and wire over the shortest possible distance.
yConnecting a power supply: Wire the power lines as short as possible.
zWire connection example
When a relay is operated and a LED is lit by the fan alarm output
←120 mA or less
←120 mA or less
OUT1
OUT2
GND
GND
0 V 0 V
Fan alarm
output
0 V
+30 V or less
+30 V or less
+24 V
VCC
GND
IN1+ 24V
IN1
-
Relay
VCS03-3
2.8 kΩ
IN2+ 24V
IN2
-
+5 to 24 V
LED
10 kΩ
2.8 kΩ
10 kΩ
Fan alarm output
Output transistor
ON (L level)
Normal
operation
Normal
operation
Alarm
generation
VCS03-3 out put
(OUT1,2)
OFF
ON
OFF
HP-13046-2
OPERATING MANUAL Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
yPlease read it thoroughly to ensure safe operation.
yAlways keep the manual where it is readily available.
Connection support module Logic Inversion Module
Photocoupler input type VCS03-3
