Oricom JSP1200 Manual de usuario
Keep this user guide for future reference.
Always retain your proof of purchase in case of
warranty service.
www.oricom.com.au
Operating Instructions
JSP1200 Waterproof Jump Starter
2
Table of Contents
Product Overview ............................................. 3
Package Contents............................................. 5
Getting Started ................................................. 5
Specications ................................................... 8
FAQ ................................................................ 10
Care and Maintenance.................................... 11
Express Warranty (Australia) ........................... 12
Cautions
• DO NOT use this unit if any cable, clamp, or cord is damaged.
• DO NOT connect the two clamps together when the jump
starter is turned on.
DO NOT connect both cable clamps to the same metallic/
conductive surface. Otherwise, the jump starter will be
damaged.
• If the Force Start feature is used, the inbuilt short circuit
protection will not be active. Take extra care of the
connections when this feature is used.
• This equipment contains a Lithium-ion Battery pack.
Do not short circuit the Battery pack.
Lithium-ion Batteries must be disposed of properly.
The Lithium-ion Battery pack contained in this equipment
may explode if disposed of in a re.
Lithium-ion Batteries should not be exposed to high
temperature environments as they may not operate
correctly in these conditions.
Always keep out of direct sunlight in conned environments.
3
Product Overview
Product Overview
NO. Function Operation
1 ON/OFF Button
(Multifunctional)
Connect devices to be charged.
LED’s light up indicating battery
capacity. If no devices are
connected press the button to
show the battery capacity.
Press and hold the button to turn
the torch on/off.
2 Charging Indicator
Lights
Shows the charging status: 25%,
50%, 75% and 100%.
3 LED Flashlight Flashlight modes: Solid, SOS,
Flash, and Off
4
Product Overview
4 USB-A Output Port
1 (QC 3.0)
Use to charge your devices (QC
3.0 compatible) faster, with 75%
increase in speed.
5 USB-A Output Port
2 (QC 3.0)
Use to charge your devices (QC
3.0 compatible) faster, with 75%
increase in speed.
6 USB-C Input &
Output (PD30W)
Charge the jump starter via
USB-A to USB-C cable.
Charge your devices (PD30W)
faster, with 75% increase in
speed via USB-C to USB-C cable.
7 Micro USB Input
Port
Charge the jump starter via the
Micro USB cable.
8 Jump Starting Port Connect the jump starter leads
into port.
9 Black Clamp Connect the black clamp to the
negative terminal of the car
battery.
10 Red Clamp Connect the red clamp to the
positive terminal of the car
battery.
11 Plug Connect to the jump starting
port.
12 Battery Clamp
Indicator Light
Shows the status of the smart
battery clamp.
13 Force Start Button Press this button if the car
battery voltage is too low.
5
Package Contents / Getting Started
Package Contents
1 x JSP1200 Jump Starter 1 x 12V Car charger
1 x Smart Battery Clamp 1 x AC Charger
1 x USB-C to USB A Cable 1 x User Manual
1 x USB-C to USB C Cable 1 x Carry Pouch
Getting Started
Charging the Jump Starter
1. Connect the jump starter to the power source via the
supplied USB-C cable, Type-A Micro USB cable or AC
Charger. Once it is fully charged, all 4 battery level indicator
lights will be on.
2. Unplug the cable when charging is complete.
NOTE:
When using the product for the rst time, please make sure that
the jump starter is fully charged.
Charging Your Devices
1. Connect your devices, including; smartphone, tablet or
other electronic devices via USB cable.
2. Disconnect the USB cable when charging is complete.
LED Torch
Press and hold the ON/OFF button for 3 seconds to turn
on the torch. Press the ON/OFF button briey to switch the
modes between Solid, SOS, and Flash. Press and hold the
ON/OFF button for 3 seconds to turn off the LED light.
6
Getting Started
Jump Start Your Car
NOTE:
This jump starter is designed for a 12V car system (all
petrol engines up to 8.0L and diesel engines up to 6.0L
only).
Check to make sure that 3 to 4 indicator lights are
illuminated (battery level is above 50%) before you jump
start your car.
Step 1: Insert the plug of the smart battery clamp
completely into the jump starter. The green and red
light indicators on the battery clamp must be ashing
alternately before moving onto
step 2.
Step 2: Connect the red clamp
to the positive terminal (+) and
the black clamp to the negative
terminal (-) of the car battery.
The green and red light indicators on
the battery clamp must be ashing
alternately before moving onto step 3.
If the red indicator light is on:
1. The battery clamp may
be connected in reverse.
Disconnect the battery clamp
from the vehicle and the
jump starter and reconnect
correctly as per steps 1
and 2.
2. Readjust the battery clamps for maximum contact with
battery terminals.
7
Getting Started
Step 3 (a): Start your car.
If your car fails to start,
disconnect the battery clamp
from the vehicle and the jump
starter. Wait for at least 30
seconds, then try again.
If your car fails to start, you can use the force start
function. See Step 3 (b).
Step 3 (b) (optional): Force
start function. Before you
begin, make sure that the battery
clamps are connected to the
correct polarity battery terminal.
Hold the force start button for 3
seconds to start your car. When
the indicator light of the smart clamp is solid green, you
must attempt to start the vehicle within 30 seconds.
Step 4：Once your car has
started, remove the battery
clamps from the car battery
within 30 seconds.
8
Specications
If any of the following are indicated, the smart clamp
turns protection on.
LED Indicator Situations
The red light is
always on
1. Battery clamp is reverse connected.
-Check if the battery clamps are
reverse connected.
2. The clamp has short-circuited.
-Check whether the two clamps are
connected together or both clamps
are connected to the same metallic/
conductive surface.
3. The temperature of the clamp exceeds
65(+/-5) degrees.
-Remove the clamp until the red/green
light ash
The green light
ashes slowly
The voltage of the jump starter is too low.
Charge the jump starter before
attempting to re-use.
Specications
Model JSP1200
Capacity 59.2Wh
Ingress Protection IP66
Micro USB input 5V/2.1A
Torch 1W LED, 100 lumens
Type-C input & output (PD30W)
5V/3A,9V/3A,12V/2.5A,
20V/1.5A, (QC18W) 5V/3A,
9V/2A, 12V/1.5A
9
Specications
Type-A USB output 1 5V/3A, 9V/2A, 12V/1.5A
Type-A USB output 2 5V/3A, 9V/2A, 12V/1.5A
Start current 600A (lasts for 1.5S)
Start current 350A (lasts
for 3S)
Peak current 1200A (lasts for 0.1S)
Short circuit protection Effective
Over-discharge protection ≤13V±0.3V
Over-temperature
protection
> 65°C±5°C
Reverse polarity protection Effective
Reverse charging protection ≥(12.6V±0.3V)
Dimensions (L*W*H) 185*100*45mm
Waterproof rating IP66 Protection against powerful
jets of water at 100kPa at
3m for 15 mins. Charge port
cover must be in place.
10
FAQ
FAQ
Q: How to turn off the jump starter?
A: The jump starter will power off automatically when no
load is detected or when charging is complete.
Q: How long does it take to fully charge the jump
starter?
A: About 9 hours through the Micro USB input port or 3
hours through the USB C input port.
Q: How many times can the jump starter start a
vehicle with full charge capacity?
A: Approximately 20 times.
Q: How many times can the jump starter fully charge
my cell phone?
A: It depends on the battery capacity of your cell phone. For
example, iPhone 12 can be fully charged 4~5 times.
Q: What are the safety protections of the smart
battery clamp?
A: Short-circuit protection, over-temperature protection,
over-voltage protection, over-charge protection, over-
discharge protection, over-current protection and reverse
polarity protection.
Tabla de contenidos
