Oregon Scientific BAR112HGLA Manual de usuario

DIGITAL WEATHER FORECASTER

WITH REMOTE THERMO-HYGRO

SENSOR AND RADIO CONTROLLED

CLOCK

MODEL NO.: BAR112HGA

USER’S MANUAL

INTRODUCTION

Congratulations on your purchase of the Weather forecaster with

cablefreesensorandradio-controlledcalendarclockBAR112HGA.

This unit has a large four-line liquid crystal display (LCD) for

displaying weather forecast information, in/outdoor temperatures

and relative humidity, radio frequency (RF) controlled calendar

clock and daily alarm. Also, the main unit can support up to three

remote sensors.

Other features include day of week display in three abbreviated

languages, crescendo alarm, and interchangeable clock display

modes.

MAINFEATURES:MAINUNIT

CH ANNE LME MMOD E/ SE T

433MH CABLE FR EE

CHANNELMEMMODE/SET

RESET

MAX

TEMP

Tested To Comply

With FCC Standards

FO R H OM E OR OF F ICE U SE

MO DEL N O. BA R112H GA

A . FRONT DISPLAY

A four line easy-to-read LCD

A1. WEATHER FORECAST WINDOW

Graphically illustrates a weather forecast

B. [ ] BATTERY-LOW INDICATOR

Activates when the remote-sensor or main unit battery power

is low

C. [ ] RADIO-RECEPTION SIGNAL

Indicates the condition of radio reception

D. [MODE/SET] BUTTON

Changes the display mode of the clock and alters time/date

setting

E. [] BUTTON

Displays the alarm time or changes the alarm set time

F. [MEM] BUTTON

Displaysminimumandmaximumtemperatureand

humidity readings and erases memory data

G. [ CHANNEL ] BUTTON

Toggles between the remote sensor channels

H. [ ((.)) ] ALARM ICON

Appears when the alarm time is displayed

I. [

] ALARM-ON ICON

Appears when the alarm is activated

J. US-TIME ZONE MAP ICON

Displays Pacific (P), Mountain (M), Eastern (E) or Central

(C)time-zone

K. WALL-MOUNTHOLE

For mounting the unit on a wall

TEMPERATURE&RELATIVE HUMIDITYALARM:

( for Channel - 1 only )

L. [ ON/OFF ] BUTTON

Enables / disables HI/LO temp alarm and HI/LO % RH alarm

M. [ HI/LO ] BUTTON

- Set the upper or lower temperature and humidity alarm

limits

- Confirms alarm settings

N. [ s] BUTTON

Advances the value of the settings for the HI/LO

temperature and humidity alarm

CLOCK:

O. [ s] BUTTON

Advances the value of a setting

P. [AL ON/OFF]BUTTON

Enables or disables the daily alarm

Q. [ZONE]BUTTON

Toggles between the 4 US time-zones : Pacific, Mountain,

Eastern or Central

R. [ RESET ] BUTTON

Returns all settings to default values

S. BATTERYCOMPARTMENT

Accommodates four (4) UM-3 or “AA” size batteries

T. REMOVABLETABLESTAND

For standing the main unit on a flat surface

FEATURES:REMOTETHERMO-HYGRO

SENSOR

A. TWO-LINELCD

Displays the current temperature and humidity monitored by

the remote unit

B. LED INDICATOR

Flashes when the remote sensor transmits a reading

C. °C/°FSLIDESWITCH

Selects between Centigrade (°C) and Fahrenheit (°F)

D. CHANNELSLIDE SWITCH

Select the remote sensor Channel 1, Channel 2 or Channel 3

E. RESET

Returns all user programmed settings to original factory set

values

F. BATTERYCOMPARTMENT

Accommodates two (2) UM-3 or AA-size batteries

G. BATTERYDOOR

H. WALL-MOUNTHOLDER

Supports the remote unit in wall-mounting

I. REMOVABLETABLE STAND

For standing the remote unit on a flat surface

BEFOREYOUBEGIN

For best operation,

1. Assign different channels to different remote units.

2. Insert batteries for remote units before doing so for the main unit.

3. Place the main unit as close as possible next to the remote unit,

reset the main unit after installing batteries. This will ensure

easier synchronization between the transmission and reception

of signals.

4. Position the remote sensor and main unit within effective

transmission range, which, in usual circumstances, range of 100

feet (30 meters) under ideal conditions.

Note that the effective range is vastly affected by the building

materials and where the main and remote units are positioned. Try

various set-ups for best result.

Though the remote sensors are weather resistant, they should be

placed away from direct sunlight, rain or snow.

BATTERYINSTALLATION:MAINUNIT

1. Gently lift up the tab on the battery compartment door.

2. Insert four (4) UM-3 or “AA” size batteries.

3. Replace the battery compartment door.

BATTERYANDCHANNELINSTALLATION:

REMOTEUNIT

The remote thermo-hygro sensor unit uses two (2) UM-3or “AA”

size batteries.

Follow these steps to install / replace batteries:

1. Remove the screws on the battery compartment.

2. Select the channel number on the [CHANNEL] slide switch.

3. Select the temperature display unit on the °C/°F slide switch.

4. Insert the batteries strictly according to the polarities shown

therein.

5. Replace the battery compartment door and secure its screws.

Replacethebatterieswhenthelow-batteryindicatoroftheparticular

channel lights up on the main unit. (Repeat the steps described in

section “BEFORE YOU BEGIN”)

Note that once a channel is assigned to a remote unit, you can only

change it by removing the batteries or resetting the unit.

LOWBATTERYWARNING

When it is time to replace batteries, the low-battery indicator will

be displayed for the selected channel.

HOWTOUSETHE TABLESTANDORWALL

MOUNTING

The main unit has a removable table stand which when connected

can support the unit on a flat surface. Or you can remove the stand

and mount the unit on a wall using the recessed screw hole.

Theremotesensorcomeswithawallmountholderandatablestand.

Main unit

Wall-mount Table Stand

Remote unit

Wall-mount Table Stand

THERESET BUTTON

This button is used when the unit is operating in an unfavorable

way or malfunctioning. To return all user programmed settings to

their original factory values, press [ RESET ] by using a blunt

stylus to hold down the button.

GETTINGSTARTED

Once batteries are placed in a given remote sensor unit, it will start

transmitting information at 40-second intervals.

For approximately a 3-minute duration, the main unit will

automatically search for signals once batteries are installed. Upon

successful reception, the individual channel temperature reading

will be displayed on the second line and the respective humidity

reading on the third line. The main unit will automatically update

its readings at about 40-second intervals.

433MH CABLE FREEZ

CHANNELMEMMODE/SET

MAX

TEM P

If no signals are received, blanks “---” will be displayed and the

kinetic wave icon will not show.

To force a signal search:

• Press and hold [CHANNEL] &[MEM] for 2 seconds to

enforce a 3-minute search.

This is useful in synchronizing the transmission and reception of

the remote and main units.

Repeat this step whenever you find discrepancies between the

reading shown on the main unit and that on the respective remote

unit.

HOW TO CHECK REMOTE AND INDOOR

TEMPERATURE&HUMIDITY

Display of readings from a remote sensor or the main unit is a one-

step procedure. The remote sensor channel or the main unit display

is indicated in a box under the kinetic-wave icon.

Todisplaytemperature/humidityreadingsfromthemainunit:

• Press [CHANNEL] until a dot is displayed in the box under the

kinetic-wave.

To display temperature / humidity readings from a remote

sensor:

• Press [CHANNEL] until the appropriate remote sensor channel

is displayed in the box under the kinetic-wave.

DISCONNECTED SIGNALS

If without obvious reasons the display for a particular channel goes

blank,press[CHANNEL]&[MEM]toenforce animmediate search.

If that fails, check:

1. The remote unit of that channel is still in place.

2. The batteries of both the remote unit and main unit. Replace as

necessary.

Note that when the temperature falls below freezing point, the

batteries of outdoor units will freeze, which will lower their

voltage supply and the effective range.

3. The transmission is within range and path is clear of obstacles

and interference. Shorten the distance when necessary.

TRANSMISSION COLLISION

Signals from other household devices, such as door bells, home

security systems and entry controls, may interfere with those of this

product and cause temporary reception failure. This is normal and

does not affect the general performance of the product. The

transmission and reception of temperature and humidity readings

will resume once the interference recedes.

Indoor

Display

Designated

Display

Remote

Display

Channel 1

Kinetic-wave

Icon

Remote

Display

Channel 2

Remote

Display

Channel 3

HOWTOREADTHEKINETICWAVE

DISPLAY

The kinetic wave display shows the signal receiving status of the

main unit. There are three possible forms:

The unit is in searching mode.

Transmission data are securely

registered.

No signal received in search mode.

REMOTE SENSOR SCANNING

The unit can be set to automatically scan and display readings from

the remote sensors and indoor readings. When the remote-sensor

scanning mode is active, the display will show the readings from

one channel for about 4-second and then proceed to the next channel

display.

To activate the remote-sensor scanning mode:

• Press and hold [CHANNEL] for 2 seconds.

To deactivate the remote-sensor scanning mode:

• Press either [CHANNEL],[MEM],[HI/LO], [ s], [ON/OFF]

(TEMP % RH AL)

COMFORTLEVELINDICATORS

The comfort level indicators COM, WET or DRY will tell you if the

curent environment is comfortable, too wet or too dry.

The comfort indicator will appear on the display when the following

conditions are satisfied:

Indicator

displays

on the unit

Temperature

Range

20°C to 25°C

(68°F to 77°F)

-5°C -+ 50°C

(23°F - 122°F)

-5°C -+ 50°C

(23°F - 122°F)

Humidity

Range

40%RH-

70%RH

OVER-

70%RH

Below

70%RH

Shows that the

Current

Environment

Ideal range for

both relative

humidity and

temperature

Contains excess

moisture.

Contains

inadequate

moisture

Indicator

Less than

20°C( 68°F)

or More than

25°C (77°F)

40%RH

70%RH Nocomment

COM

WET

DRY

TEMPERATURE,HUMIDITY&PRESSURE

TREND INDICATORS

The temperature-trend, humidity-trend and pressure-trend

indicators show the trends of collected readings. Arrows indicate

a rising, steady or falling trend.

Note: If the reading goes above or below the measuringrange of the

main unit or the remote unit ( stated in specification), the display

will show “HHH” or “LLL”.

MAXIMUMANDMINIMUMTEMPERATURE

ANDHUMIDITY

The maximum and minimum recorded temperature and humidity

readings will automatically be stored in the memory.

To display the maximum and minimum display memory:

1. Select the channel to be checked.

2. Press [MEM] once to display the maximum temperature and

humidityand press [MEM]againtodisplay minimum temperature

and humidity. The respective indicators, MAX or MIN will be

displayed.

To clear the memory:

• Press and hold [MEM] for 2 seconds.

Ifyou press [MEM]now,themaximumandminimumrecordingswill

have the same values as the current ones until different readings are

recorded.

HOWTOUSECHANNEL-1TEMPERATURE/

HUMIDITYALARM

Upper and lower temperature and humidity limits for Channel-1 can

be set so that an alarm activates when the limits are exceeded.

The high and low temperature and humidity displays are selected

by sequentially pressing [ HI/LO ].

Rising

Arrow indicator

Humidity Trend Steady Falling

Rising

Arrow indicator

Pressure Trend Steady Falling

Rising

Arrow indicator

Temperature

Trend Steady Falling

The high-low displays are as follows:

Sequence RespectiveDisplay

Pressing HI/LO once Enters HI temperature display

Pressing HI/LO twice Enters HI humidity display

Pressing HI/LO third time Enters LO temperature display

Pressing HI/LO fourth time Enters LO humidity display

To set a high or low temperature or humidity alarm:

1. Press [HI/LO], Channel-1 will be displayed.

2. Press [s ]to set the temperature or humidity limit. Each press

will increase increments by one degree or percentage. Press and

hold the button for a rapid-scrolling sequence by increments of

five.

Note: The temperature range is from -50°C (-58°F) to +70°C

(158°F).

If this is the first time you set the limits, the lower limit will

start from -50°C (-58°F) and the upper limit +70°C (158°F).

Otherwise, the reading will start from the temperature last

selected.

The humidityrange is from 2% to 98%.

If this is the first time you set the limits, the lower limit will

start from 2% and the upper limit 98%. Otherwise, the reading

will start from the humidity last selected.

3. Repeat the steps to set the upper temperature andhumiditysetting

and the lower temperature and humidity settings.

4. When finished, press [HI/LO] to set another limit or wait 16

seconds and the unit will automatically return to the normal

display. The respective HI, LO or both indicators will be

displayed to signify the status of the alarm.

If a channel other than channel-1 is selected, the display will switch

to channel-1 and flash when the alarm activates. If left untouched,

the alarm will activate for 1 minute. Press either [CHANNEL],

[MEM],[HI/LO],[s],[ON/OFF]

(TEMP % RH AL)

to momentarily stop the alarm. The alarm will activate again if the

limit continues to exceed the set limit.

Note: If a second limit is passed while an alarm is active, the first

alarm will complete its 1-minute cycle and the alarm will continue

to activate for a second minute to indicate that a second limit has

been surpassed.

To disable an alarm:

1. Enter the setting mode by pressing [HI/LO].

2. Then, press [ON/OFF].

The alarm has been disabled. Display will show “---” to indicate

such deactivation and will not sound at the previously set limit.

To disable a sounding alarm:

• Press either [CHANNEL], [MEM],[HI/LO], [ s],[ON/OFF]

(TEMP % RH AL)

WEATHERFORECASTFUNCTION

Theunitis capable of detecting atmospheric pressurechanges.Based

on collected data, it can predict the weather for the forthcoming 12

to 24 hours. The effective range covers an area of 18 to 30 miles.

NOTE:

1. The accuracy of a general pressure-based weather forecast is

about 70% to 75%.

2. The weather forecasts from this unit are predictions that cover

the next 12 to 24 hours. It may not necessarily reflect the current

situation.

3. The “Sunny” icon, implies clear weather.

CALENDARCLOCK DISPLAYMODES

The BAR112HGAsupports 2 time display modes in the sequence

of:

MODE1. Hour-Minute-Second (of local time)

Month-Day (of local time)

MODE2. Hour-Minute-Day of the Week (of local time)

Month-Day (of local time)

Each press on the [MODE/SET] button will toggle the display in

the above order.

Note: The bottom line of the display will be replaced by the alarm

time if the [] button is pressed.

ABOUTRADIORECEPTION

The BAR112HGA is designed to automatically synchronize its

calendar clock when it is within range of the radio signal from the

U.S. Atomic clock.

When the unit is receiving radio signal, the RADIO RECEPTION

signal will start to blink. A complete reception generally takes

about 2to 10 minutes, depending on the strength of the radio signal.

When the reception is complete, the RADIO RECEPTION signal

will stop blinking. The strength of the reception will remain until

the next scanning cycle takes place.

For better reception, place the clock away from metal objects and

electrical appliances to minimize interference.

If you wish to disable the auto-reception feature, press the

[ ZONE ] button for three seconds. The radio reception signal []

and the outline of the US-Map icon will disappear. The unit will

not respond to radio signals.

To enable the feature again, press the[ ](clock) button for three

seconds.

The radio reception signal [ ] and the outline of the US-Map icon

will start blinking to initiate reception automatically.

Cloudy

SunnyForecast Rainy

Slightly Cloudy

Indicator

displays

on the unit

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Estación meteorológica de Oregon Scientific

Oregon Scientific

Oregon Scientific BAR113 Manual de usuario

Oregon Scientific

Oregon Scientific BAR998HGN Manual de usuario

Oregon Scientific

Oregon Scientific RAR502X Manual de usuario

Oregon Scientific

Oregon Scientific TREVISO BAR986HGA Manual de usuario

Oregon Scientific

Oregon Scientific BAR916HG Manual de usuario

Oregon Scientific

Oregon Scientific BA900 Manual de usuario

Oregon Scientific

Oregon Scientific WMH90 Manual de usuario

Oregon Scientific

Oregon Scientific WMR300A Manual de usuario

Oregon Scientific

Oregon Scientific BAR218HGX Manual de usuario

Oregon Scientific

Oregon Scientific BA812E Manual de usuario

Oregon Scientific

Oregon Scientific BA169 Manual de usuario

Oregon Scientific

Oregon Scientific BAR808HG Manual de usuario

Oregon Scientific

Oregon Scientific BAR608HGA Manual de usuario

Oregon Scientific

Oregon Scientific WMR300 Manual de usuario

Oregon Scientific

Oregon Scientific BAR218HGX Manual de usuario

Oregon Scientific

Oregon Scientific BHB613 Manual de usuario

Oregon Scientific

Oregon Scientific RAR500N Manual de usuario

Oregon Scientific

Oregon Scientific RMR203HG Manual de usuario

Oregon Scientific

Oregon Scientific Starck PS-L06 Manual de usuario

Oregon Scientific

Oregon Scientific BAA968HG Manual de usuario

Oregon Scientific

Oregon Scientific BAR610P Manual de usuario

Oregon Scientific

Oregon Scientific BAR938HG Manual de usuario

Oregon Scientific

Oregon Scientific Weather Home RAR213HGX Manual de usuario

Oregon Scientific

Oregon Scientific BAR636A Manual de usuario

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

La Crosse Technology

La Crosse Technology C86371 Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

La Crosse Technology

La Crosse Technology WS-2210 Manual de usuario

La Crosse Technology

La Crosse Technology WS-811561 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario