Orbit Power Stride 23 Elliptical OBE655T Manual de usuario

OBE655T

Elliptical Cross Trainer

Owner’s Manual

OBE655T

Table of Contents

Product Safety Page.01.............................................................................

Trouble Shooting & Maintenance & Warm Up ............... Page.12

Assembly ...................................................................................... Page.04

Hardware & Tools ...................................................................... Page.03

Computer ....................................................................................... Page.13

Part List ........................................................................................... Page.24

Part Drawing & Box A/B Contents ....................................... Page.02

Exploded View ............................................................................ Page.25

Product Safety

Basic precautions should always be followed, including the following safety instructions

when using this equipment: Read all instructions before using this equipment.

1. Read all the instructions in this manual and do warm up exercises before using this equipment.

2. Before exercise, in order to avoid injuring your muscles, warm-up exercise for every muscle

group is highly recommended. Please refer to the Warm Up pages for pre and post workout.

3. Please make sure all components are not damaged and in working order before use. This

equipment should be placed on a flat surface while in use. Using a mat or other material on

the ground is recommended.

4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that

might catch in any part of the equipment.

5. Do not attempt any maintenance or adjustments other than those described in this manual.

Should any problems arise, discontinue use and consult an Authorized Service Representative.

6. Be careful when stepping on or leaving the pedals. Always hold the handlebars first and make

sure the pedal at your side is at its lowest position. Step on the pedal, and stride over the main

frame then step on the other pedal. When using, please hold onto the handlebars. To ensure

the pedals run smoothly push or pull on the handlebars first, then follow with leg motion.

When stepping off the machine, make sure one pedal is at its lowest position and step out of

there before stepping out of the pedal at the highest position.

7. Do not use the equipment outdoors.

8. This equipment is for household use only.

9. Only one person should be on the equipment while in use.

10. Keep children and pets away from the product while in use. This machine is designed for

adults only. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop

exercising immediately and consult your physician before continuing.

11. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising

immediately and consult your physician before continuing.

12. The maximum weight capacity for this product is 330 lbs/150 kgs.

Before beginning any exercise program consult your physician.

This is especially important for the persons who are over 35 years

old or who have pre-existing health problems. Read all instructions

before using any fitness equipment.

WARNING:

CAUTION: Read all instructions carefully before operating this product.

Retain this Owner’s Manual for future reference.

Part Drawing & Box A/B Contents

A01 A07/A08 A13/A14

A02

MainBody

Left/Right

Wheel Bar Set Handrails

Front Post

1PC 1Set 1Set

1PC

Computer

Left

Dual Action Arm Set

Right

Dual Action Arm Set

Foot Pedal 1PC

1Set 1Set

2PCs

A15 A03 A04

C12

A12 A05/A06 D08 C07/C08

C11

Guide Rail

Left/Right

Foot Pedal Bar Set AC Adaptor Left/Right Front Post

Decorative Covers

Nut Cap

1PC 1Set 1PC 1Set

2PCs

Handrail Arm

Decorative Covers-A/B Bottle Holder

Left/Right

D Shape End Cap

Left/Right Pivot Cap

2Sets 1PC 2Sets

2Sets

C17/C18 C27 C28/C29

Box B

Box A

Hand Pulse Handlebar 1PC

Left/Right Wheel Cap 2Sets Lubricant 1PC

D02

C34

Foot Pedal Pad 1Set

C30/C31 C32/C33

Water Bottle 1PC

Pivot Cap

For Crank Link Tube 2PCs

C35

Hardware & Tools

B32 (2) B33 (7)

B21 (5)

B40 (7)

B28 (1)

Hexagon Head Bolt

M8x16mm

Washer

5/16”x20x2.0t

Screw M5x16mm

Bolt M8x25mm

6PCs 8PCs

30PCs

2PCs

Bolt M8x50mm 4PCs

B29 (3) B30 (4)B23 (2)

Nylon Nut M8Bolt M6x15mm 4PCs8PCs

Curve Washer

M8x20x1.5t 4PCs

Hex Tool With

Phillips Screwdriver

(13mm/14mm) 1PC Allen Wrench (M5) 1PCAllen Wrench (M4) 1PC

B24 (1)

Bolt M8x92mm 2PCs

B13 (6) B14 (3)

Bolt M8x16mm 16PCs Bolt M8x20 4PCs

B30 (4)

Curve Washer

M8x20x1.5t 16PCs

B29 (5)

Nylon Nut M8 2PCs

Pack A

Pack B

(8) (9)(6)

Assembly

1. Guide Rail Installation

2. Adjusting the Adjustable Leveler

Turn the Adjustable Levelers (C05) on the MainBody (A01) and Guide Rail (A12) as needed to level the

elliptical trainer.

The elliptical trainer has to be leveled to prevent from wobbling or shaking during the exercise.

3. Front Post Installation

Connect the Extension Sensor Wire II (D05) from the MainBody (A01)

to the Extension Sensor Wire I (D04) from the Front Post (A02) and

carefully tuck the wires into the MainBody (A01) before attaching

the Front Post (A02) onto the MainBody (A01).

Attach the Front Post (A02) onto the MainBody (A01) and fully

tighten with 4 Bolts (B14).

[Tighten bolts with the Hex Tool With Phillips Screwdriver provided]

For easier installation of the Guide Rail (A12), place a block of wood under the

MainBody (A01).

Attach the Guide Rail (A12) onto the tubes of the MainBody (A01) with

16 Bolts (B13) and 16 Washers (B30) that were removed.

Assemble the Left and Right D Shape End Cap(C28/C29) into the tube of the

MainBody(A01) and Guide Rail (A12).

[Remove/Tighten bolts with the M5 Allen Wrench provided]

M5 Allen Wrench

Hex Tool With Phillips Screwdriver (13mm/14mm)

C29

C28

A12

B30

B13

C29

C28

A01

B13

B30

B13

C05

A12

A01

Adjusting the Adjustable Leveler

A02

B14

B14 D05

D04

B14

D05

D04

block of wood

1.)

2.)

3.)

1.)

2.)

(B13)Bolt M8x16mm---16PCs

(B30)Washer M8x20x1.5t---16PCs

(B14)Bolt M8x20mm---4PCs

Assembly

4. Lubricating the Horizontal Axle and Crank Axle

Apply lubricant to the horizontal axles of the Front Post (A02)

and the axles of the right and left Crank (A11).

5. Left and Right Foot Pedal Linkbar Installation

Remove the tape from the joint of the Right Dual Action Arm Set (A04).

Insert the Right Dual Action Arm Set (A04) all the way onto the horizontal axle of the Front Post (A02) and secure

the Right Dual Action Arm Set (A04) in position with 1 Bolt (B32) and 1 Washer (B33).

[Tighten bolt with the Hex Tool with Phillips Screwdriver provided]

Remark: Gently apply lubricant evenly on Front Post (A02).

Brush tool is recommended.

Hex Tool With Phillips Screwdriver (13mm/14mm)

(B33)Washer 5/16”x20x2.0t---6PCs

(B32)Bolt M8x16mm---6PCs

Lubricant

A02

A11

Lubricating the

horizontal axle

and crank axle.

Remove the tape from the joint of the Right Wheel Bar Set (A08).

Insert the Right Wheel Bar Set (A08) onto the Crank (A11) axle.

The Wheel (C20) has to be placed on the Rail Aluminum Plate (F01).

Secure the Right Wheel Bar Set (A08) in position with 1 Bolt (B32) and 1 Washer (B33).

Insert the axle of the Right Foot Bar Set(A06) onto the Right Wheel Bar Set(A08), secure the Right Foot

Bar Set(A06) in position with 1 Bolt (B32) and 1 Washer (B33).

[Tighten bolt with the Hex Tool with Phillips Screwdriver provided]

CAUTION: Make Sure The Bushing Spacer (B41) Was Perfectly In Position Before Securing

The Bolts.

1.)

2.)

3.)

4.)

5.)

6.)

C11 B32

B33

A08

A06

Assembly

Hex Tool With Phillips Screwdriver (13mm/14mm)

A06

A04

A08 B24

B33

B29

M8x45 Nut Cap (C11)

Untie the wire and remove 2 Washers (C22) from the bottom end of the Right Dual Action Arm Set (A04).

Place 2 Washers (C22) back onto the joint of the Right Dual Action Arm Set (A04).

Pull the Right Foot Bar Set (A06) up onto the Right Dual Action Arm Set (A04) and align bolt holes.

Then attach the Right Foot Bar Set (A06) onto the Right Dual Action Arm Set (A04) with 1 Bolt (B24),

1 Nut (B29), and 1 Washer (B33) that were removed.

[Tighten bolt and nylon nut with the Hex Tool with Phillips Screwdriver and M5 Allen wrench provided]

Repeat above steps to install the Left Dual Action Arm Set (A03) onto the horizontal axle of the Front

Post (A02) and Left Wheel Bar Set (A07) onto the Crank (A11) axle.

Fit one Nut Cap (C11) onto M8x16mm Hexagon Head Bolts (B32) of the Right Rotate Bar (A08).

7.)

8.)

M5 Allen Wrench

9.)

Remark: Please use the assembly drawings of steps No. 1-9 at Page No. 7.

(B33)Washer 5/16”x20x2.0t---2PCs

(B29)Nut M8xP1.25x7.7t---2PCs

(B24)Bolt M8x92mm---2PCs

Assembly

A07

C23

B41

B33

B32

C11

B32 B33

B41

C11

B32

B33

B41

C23

A08 B41

B33

B32

A04

A06

B24

B33

B29

B32

B33

B41

A02

A05

A03

B32

B33

B41

C25

E02

C25

C24

C24 B31

C22

B41

B24

B29

B33

INCORRECTCORRECT

B41 B41

Assembly

6. Pivot Covers Assembly

Assemble two sets of Pivot Cover(C30/C31) at the pivot of Left and Right Dual Action Arm(A03/A04) and

Foot Pedal bar(A05/A06) with 8 Screws(B21).

Assemble two pcs of Pivot Cover for Crank Link(C35) to the pivot of Right/Left Wheel Bar Set(A08/A07) and

Crank(A11) using 4 Screws (B21).

Assemble two sets of Wheel Caps(C32/C33) to the wheel of the Left and Right Wheel Bar Set(A07/A08) with

8 Screws(B21).

[Tighten bolts with the Hex Tool With Phillips Screwdriver provided]

Hex Tool With Phillips Screwdriver (13mm/14mm)

(B21)Screw M5x16mm---20PCs

C33

C32

C33 B21

B21

C35

C31

C30

C31

B21

1.)

2.)

3.)

A04

A03

A07

A08

Tabla de contenidos

Otros manuales de Entrenador elíptico de Orbit

Orbit

Orbit Silver XT Manual de usuario

Orbit

Orbit OBE794 Manual de usuario

Orbit

Orbit Phoenix CDXP Manual de usuario

Orbit

Orbit OBEI50A Manual de usuario

Orbit

Orbit OBE165AF Manual de usuario

Manuales populares de Entrenador elíptico de otras marcas

Weslo

Weslo Momentum 4.0 Elliptical Manual de operación y mantenimiento

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manual de usuario

Torque Fitness

Torque Fitness XPLLP Manual de usuario

Octane Fitness

Octane Fitness PRO3700C Manual de usuario

Xterra

Xterra FS5.8e Manual de usuario

Bodyguard

Bodyguard E-40 Manual de usuario

Bonn Germany

Bonn Germany Concept 2.2 Manual de usuario

Precor

Precor Resolute RSL 620 Manual de usuario

NordicTrack

NordicTrack E 9.2 Elliptical Manual de usuario

Vision Fitness

Vision Fitness X6600iNetTV Manual de usuario

Matrix

Matrix MX-A5x Manual de usuario

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manual de usuario

Sears

Sears FREE SPIRIT C249 30737 0 Manual de usuario

True

True FS-64 Manual de usuario

Sport-thieme

Sport-thieme ST 310 Manual de usuario

VIRTUFIT

VIRTUFIT CTR 1.1 Manual de usuario

Kettler

Kettler GIRO C 1 Manual de usuario

CIRCLE FITNESS

CIRCLE FITNESS E7 Manual de usuario