Oracle MICROS 110 Manual de usuario
1
Oracle® MICROS Kiosk 110 Assembly Addendum
Introduction
This addendum provides important assembly information for the Oracle MICROS Kiosk 110.
Installation Notes
•Assemble the kiosk in a dry, well-lit area with a level surface.
•To assist with assembly, use a magnetic tip screwdriver.
•The kiosk must be securely bolted to the floor to ensure safety.
•References to Ingenico, i-Series devices, Star printers, and ELO workstations do not apply to this installation
scenario and can be ignored.
•This release of the kiosk supports the Oracle MICROS Workstation 625/655 in landscape orientation and the Oracle
MICROS Express Station 400 in portrait orientation.
Oracle MICROS Kiosk 110 Boxes
Note that your installation may not include some optional components.
Core Components
Box Number Oracle Part Number Model / Description
*** Varies Oracle MICROS Workstation 625/655
*** Varies Oracle MICROS Express Station 4 Series
1* 7602031
Oracle MICROS Kiosk 110
*Includes two interior boxes:
•Box 1A: stand top (ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP)
•Box 1B: stand base (ELO-STAND-SELF-SERVICE-15-22-FLOOR-BASE)
Electronic versions of ELO stand documentation can be downloaded from
the ELO website at https://www.elotouch.com/accessories-wallaby-self-
service-stands.html
2 7601142 External power supply for Oracle MICROS Workstation 6 Series
IMPORTANT:
•Some steps/parts described in the original ELO assembly instructions do not apply and can
be ignored.
•This addendum contains important information not included in the original assembly instructions.
•Use this addendum as the primary overview for assembling the kiosk.
To simplify the instructions in this addendum, Kiosk 110 shipping boxes have been assigned
“virtual” box numbers. Refer to the table below for more information about box contents,
part numbers, etc.
ACTUAL SHIPPING BOXES ARE NOT MARKED AS BOX 1, BOX 1A, BOX 2, BOX 3,
ETC.
2
Optional Components
Box Number Part Number Model / Description
3 7602033 Payment cradle for Verifone MX915
4 7602034 Payment cradle for Verifone e355
5* 7602032 Scanner, scanner cable, L-bracket, and screws
*Includes one interior box:
•Box 5A: Zebra scanner
6 Varies Printer
(Epson TM-T88 or Bixolon SRP-350)
Assemble the Kiosk
1. Open Box 1 and the two interior boxes (Box 1A and Box 1B).
The documentation in Box 1A (ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP) begins with the countertop stand
assembly instructions. The countertop stand is not supported at this time. Skip to the floor stand assembly
instructions to begin.
Assembly guide cover page for the ELO floor stand. This is your starting point.
The following items in Box 1A (ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP) do
not apply to this assembly scenario and can be ignored:
•Cable Cover, Windows
•Display Bracket, Android
3
Follow the assembly instructions for Box 1A (ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP and E797162 ELO-
STAND-SELF-SERVICE-15-22-FLOOR-BASE), and include the changes described below:
a. Box 1A, Steps 1-3: Follow as directed.
b. Box 1A, Step 4: Power strip not included. To mount a customer-supplied power strip, follow the Step 4
instructions.
c. Box 1A, Step 5: Take the workstation power supply from Box 2and use the straps from Box 1Ato secure it to
the stand interior. Insert the power cord into the workstation power supply you mounted in the stand interior,
and then route the cable down and out from under the base plate as required.
−If your installation includes a payment device with a power supply, install the payment device power
supply now.
−If your installation includes a printer, install the printer power supply now (Box 6).
d. Box 1A, Step 6: Follow as directed.
e. Box 1A, Step 7: This install supports the Windows Display Bracket only.
f. Box 1A, Step 8: Use position A for the Oracle MICROS Workstation 625/655 in landscape orientation. Use
position C for the Oracle MICROS Express Station 400 in portrait orientation.
g. Express Station 4 Series Note: Route a C13 power cord from the stand interior, and then through the
rectangular opening on the display bracket swinging plate.
Routing a C13 power cord through the display bracket
h. Box 1A, Step 9: After installing the USB Hub, do not continue to Step 14 as instructed. Instead, mount the
Oracle MICROS Workstation 625/655 on the kiosk.
4
Mount the Oracle MICROS Workstation 625/655 or the Oracle MICROS Express
Station 4 Series on the Kiosk
2. Unpack the Oracle MICROS Workstation 625/655 or Oracle MICROS Express Station 400.
3. Remove the I/O panel cover from the workstation or Express Station. If you cannot easily slide off the cover you may
need to remove the cover security screw.
Removing the I/O panel cover from the Oracle MICROS Workstation 625/655
4. Take the metal standoffs from Box 2and install them in the four VESA holes on the back of the workstation,
and then partially install M4 screws from Box 1A / Bag L in the top two standoffs.
Oracle MICROS Express Station 4 Series Installation Note
To mount the Oracle MICROS Express Station 400 in portrait orientation, you must first install the optional
Portrait Mode Centering Plate for Express Station 4 Series. For more information, refer to the Portrait
Mode Centering Plate for Express Station 4 Series documentation on the final page of this document.
Verifone e355 Important Note
If your installation includes a Verifone e355 payment device, you must install the appropriate EMV payment
cradle on the kiosk display bracket before mounting the workstation on the kiosk. For detailed instructions
on installing the Verifone e355 EMV payment cradle, refer to Installing the Verifone e355 on page 13 of this
addendum.
5
5. Mount the workstation or Express Station on the kiosk by inserting the two standoffs with the M4 screws into the top
display bracket holes. Slide the unit down into the smaller grooves, and then tighten the M4 screws.
Follow the Box 2 assembly instructions, and include the changes described below:
a. Box 2, Step 1: Does not apply to this assembly scenario and can be ignored.
b. Box 2, Step 2: Follow as directed.
c. Box 2, Step 3: Does not apply to this assembly scenario and can be ignored.
d. Box 2, Step 4: Follow as directed.
e. Box 2, Step 5: Does not apply to this assembly scenario and can be ignored.
f. Box 2, Step 6: If your installation does not include any optional components, replace the I/O panel cover (“cable
casing”). If your installation does include optional components (payment device, printer, etc.), install all
components and connect the required cables before replacing the I/O panel cover.
Optional: Mount a Barcode Scanner
6. Open Box 5and follow the steps below to mount the barcode scanner on the kiosk:
a. Remove the cable clip from the scanner by pinching the side tabs of the clip and sliding it away from the
scanner.
Removing the cable clip from the scanner.
6
b. Plug the Micro USB cable into the scanner, and then replace the cable clip.
Scanner with Micro USB cable and cable clip.
When using the scanner with the Workstation 625/655 in landscape orientation:
c. Install the scanner on the right corner of the L-bracket by placing the scanner logo-side down and positioning
the L-bracket over the mounting holes on the scanner. Secure the scanner with two M3 screws from Box 5.
Installing the M3 screws to secure the scanner to the L-bracket.
7
Example of the scanner/L-bracket assembly.
d. Insert the scanner/L-bracket assembly between the floor head assembly and the display bracket, and then align
the top L-bracket mounting holes with the lower mounting holes on the display bracket. Secure the scanner/L-
bracket assembly with two M4 screws.
8
Attaching the scanner/L-bracket assembly to the floor head assembly. Image shows optional EMV cradle.
9
e. Connect the scanner cable to the USB hub, and then use the cable tie mounts and cable ties to route the cable
as shown below.
The dashed line shows the proper scanner cable routing path.
NOTE:
Route the cable from the outside through the lower rectangular opening. If you route the
cable directly into the scanner bracket, the cable will be severed when you close the display
bracket.
10
When using the scanner with the Express Station 4 Series in portrait orientation:
f. Install the scanner on the short extension of the L-bracket by placing the scanner logo-side down and
positioning the L-bracket over the mounting holes on the scanner. Secure the scanner with two M3 screws from
Box 5.
Installing the M3 screws to secure the scanner to the L-bracket (Express Station 4 Series portrait configuration)
Example of the scanner/L-bracket assembly (Express Station 4 Series portrait configuration)
g. Align the top L-bracket mounting holes with the bottom mounting holes on the display bracket. Secure the
scanner/L-bracket assembly with two M4 screws. Refer to the following image for more information.
Tabla de contenidos
