Optex FTN-R Manual de usuario
N219
CONTENTS
1 INTRODUCTION
1-1 BEFORE INSTALLATION................2
1-2 PARTS IDENTIFICATION................3
1-3 DETECTION AREA..........................4
2 INSTALLATION
2-1 WIRING DIAGRAM..........................4
2-2 TRANSMITTER PREPARATION.....5
2-3 BEFORE WALL MOUNTING...........6
2-4 STACKING METHOD ......................7
2-5 SIDE-BY-SIDE AND
TOP-TO-BOTTOM METHOD ........11
3 WALK TEST
3-1 WALK TEST...................................13
4 DIP SWITCH SETTING
4-1 WALK TEST MODE.......................14
4-2 BATTERY SAVING TIMER ............14
4-3 ALARM & TROUBLE OUTPUT ......14
4-4 LED................................................15
4-5 PIR SENSITIVITY..........................15
4-6 ANTI-MASKING.............................15
5 OTHERS
5-1 WALL TAMPER (OPTION)
CONNECTION...............................16
5-2 LED LIGHT PATTERN ...................16
6 BATTERY
6-1 HOW TO REPLACE BATTERY .....17
6-2 BATTERY LIFE..............................18
7 SPECIFICATIONS
7-1 SPECIFICATIONS .........................19
7-2 DIMENSIONS................................20
FTN-R Battery operated model with 2 PIRs
FTN-RAM FTN-R with anti-masking
Long battery life
Easy wiring by a connector
Multi fixing transmitter box
Compact design
190° adjustable bracket
Intelligent AND logic
Digital anti-masking (RAM model)
Wall tamper (option)
•
•
•
•
•
•
•
•
NO.59-1646-0 091201
INSTALLATIONINSTRUCTIONS
Compact outdoor
detector
Compact outdoor
detector
fit series
fit series
- 1 -
1INTRODUCTION
1-1
BEFORE INSTALLATION
Warning Failure to follow the instructions provided with this indication and improper
handling may cause death or serious injury.
Caution Failure to follow the instructions provided with this indication and improper
handling may cause injury and/or property damage.
The check mark indicates recommendation.
The nix sign indicates prohibition.
Warning Caution Caution
Do not remove the PCB. Do not remove the separate box
tamper.
Do not touch the PCB except for the
DIP switch.
ON
123456
ON
123456
Mounting height. Keep the detector parallel to the
ground.
Consider the direction a person is
approaching from, as well as the
detection area.
Install the detector in a place where it is free from false alarm factors. For example:
Sunlight and reflection•Heat source•Objects moving in the wind•
0.8 – 1.2 m
(2'7" – 3'11")
Parallel Tilt
- 2 -
Separate box
Separate box tamper
Main unit
Bracket
Fixture
Main unit cover
Lens
1-2
PARTS IDENTIFICATION
Connector for POWER and ALARM
Connector for TROUBLE
Screw kit
For joint For wall mounting
Screw (M3 × 10 mm)
Plate nut
Screw (3 × 20 mm)
Note>>
Transmitter and battery are not included.
-Optional accessories
Wall tamper (WRS-03)
•
Separate box cover
Sponge
Sponge
Sponge for transmitter
- 3 -
0' 5' 10' 15'
0.8
0
(m)
1.0
1.2
2'7"
0'(ft.)
3'3"
3'11"
102345
(m)
(ft.)
0' 5' 10' 15'
0.8
0
(m)
1.0
1.2 102345
(m)
2'7"
0'(ft.)
3'3"
3'11"
(ft.)
0
10
0'
0'
5'
5'
5'
10'
10'
10'
15'
15'
15'
2345
1
1
1
2
3
4
5
(m) (ft.)
(ft.
)
(m)
2
4
5
3
Separate box tamper
Trouble
Alarm
Wall tamper (option)
*For wall tamper wiring (option), refer to page
16.
Separate box Main unit
Transmitter
1-3
DETECTION AREA
Top view Side view
2 m detection length
5 m detection length
Adjustable range: 95° (by 5° pitch)
Adjustable range: 95° (by 5° pitch)
2INSTALLATION
2-1
WIRING DIAGRAM
-Overall wiring diagram
Notes>>
The battery in the transmitter is shared with the detector.
Connection for TROUBLE is used when monitoring for Tamper and Anti Mask.
•
•
- 4 -
35 (1.38")
130 (5.12")
30 (1.18")
2-2
TRANSMITTER PREPARATION
The transmitter used should have the internal dimensions of H 130 × W 30 × D 35 mm.
(H 5.12" × W 1.18" × D 1.38")
-When monitoring ALARM and TROUBLE using the transmitter with 1 external input
External input is N.C. External input is N.O.
3
... DIP switch 3: OFF (N.C.)
3
... DIP switch 3: ON (N.O.)
-To monitor only the ALARM using a
transmitter with 1 external input -To monitor the ALARM and TROUBLE
using a transmitter with 2 external inputs
Connectors to be used
Connector for POWER and ALARM
Connector for TROUBLE
Red Black
How to position a battery
Connector for POWER
and ALARM
Connector for
TROUBLE
Connector for
POWER and ALARM
N.C. N.O.
Unit: mm (inch)
- 5 -
3Hold the top of the bracket and
remove the main unit.
Note>>
Be sure to keep connectors installed
through the bottom part of bracket after
main unit is removed.
•
Bracket
Main unit
2
1
Bracket
Main unit
2
1
2-3
BEFORE WALL MOUNTING
1Open the main unit cover. 2Remove the fixture.
FixtureFixture
4Open the separate box.
Note>>
Do not remove the separate box
tamper.
•
- 6 -
5Select the mounting method.
Stacking method
(Page 7)
Side-by-side method
(Page 11)
Top-to-bottom method
(Page 11)
Note>>
Be sure to mount the main
unit on the top.
•
2-4
STACKING METHOD
For the side-by-side method and the top-to-bottom method, refer to page 11.
6Open the knockout.
Separate box Separate box cover
Joint screw
knockout
Wall mounting
knockout
Wall mounting
knockout
Wiring knockout
Joint screw
knockout
Separate box Separate box cover
Joint screw
knockout
Wall mounting
knockout
Wall mounting
knockout
Wiring knockout
Joint screw
knockout
7Pull the connectors through the wiring
knockout.
- 7 -
8Attach the separate box cover and the bracket.
Notes>>
Be careful not to attach separate box cover upside down.
Be careful not to pinch wires.
•
•
Screw (3 × 10 mm)
Screw (3 × 10 mm)
Sponge
Plate nut Wiring
Sponge
Plate nut
Double-sided tape for
temporary fixing
Screw (3 × 10 mm)
Screw (3 × 10 mm)
Sponge
Plate nut Wiring
Sponge
Plate nut
Double-sided tape for
temporary fixing
9Hold the top part of the bracket and
mount the main unit.
1
3
2
1
3
2
10 Mount the separate box on the wall.
Screw (3 × 20 mm)
Screw (3 × 20 mm)
Mounting height:
0.8 – 1.2 m (2'7" – 3'11")
Screw (3 × 20 mm)
Screw (3 × 20 mm)
Mounting height:
0.8 – 1.2 m (2'7" – 3'11")
100 mm
(3.94")
- 8 -
13 Determine the horizontal detection
angle and attach the fixture.
Note>>
To make adjustments, remove the
fixture.
•
Angle pitch: 5°
95° 95°
Angle pitch: 5°
95° 95°
Note>>
Check that the fixture and bracket
engage correctly.
•
Note>>
Check that the fixture and bracket
engage correctly.
•
11 Connect the connectors.
Separate box side Main unit side
Red
Black
White
Yellow
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Tamper
Orange: Tamper
Grey: Tamper
Green
Blue
Brown
Orange
Grey
Separate box side Main unit side
Red
Black
White
Yellow
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Tamper
Orange: Tamper
Grey: Tamper
Green
Blue
Brown
Orange
Grey
Notes>>
The tamper output is not exclusive. The
Anti-masking and Tamper circuits share
the Trouble output.
For the wall tamper wiring connection
(option), refer to page 16.
To detect cutoff of tamper
input wires (3 wire
line) as shown in the
illustration, cut the orange
jumper wire provided for
purpose of detection.
In this case, be sure to
use the connector of the separate box
tamper. Otherwise, the trouble output
will remain on.
•
•
•
12 Install the transmitter and attach the
separate box cover.
Note>>
Please use the sponge for transmitter
when needed.
•
1
2
3
Transmitter
1
2
3
Transmitter
- 9 -
14
Determine the detection length. (2 m or 5 m)
If 2 m is required, rotate the lower lens
180 degrees.
Note>>
Do not remove the upper lens.•
5 m detection length
(Factory default) 2 m detection length
Side view
0' 5' 10' 15'
0.8
0
(m)
1.0
1.2
2'7"
0'(ft.)
3'3"
3'11"
102345
(m)
(ft.) 0' 5' 10' 15'
2'7"
0'(ft.)
3'3"
3'11"
0.8
0
(m)
1.0
1.2
(ft.)
102345
(m)
Side view
15 Attach the main unit cover.
Note>>
To prepare for walk test, check that DIP
switch 1 (WALK TEST MODE) is set to
“ON (TEST)” before attaching main unit
cover.
•
16 Perform walk test.
For details, refer to page 13.
17 After walk test is complete, set DIP
switch 1 (WALK TEST MODE) from
“ON” to “OFF”.
Note>>
The battery life will be shortened unless
the DIP switch 1 is set to “OFF”.
•
- 10 -
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sensor de seguridad de Optex
Optex
Optex HX-40 Manual de usuario
Optex
Optex VX-402R Manual de usuario
Optex
Optex REDSCAN mini-Pro Series Manual de servicio
Optex
Optex inSight INS-HX-80N Manual de usuario
Optex
Optex AX100 Manual de usuario
Optex
Optex RXC-RDT-X5 Manual de usuario
Optex
Optex MX-40QZ Manual de usuario
Optex
Optex AX-350DH MK III Manual de usuario
Optex
Optex PRO SWING OA-EDGE1 T Manual de usuario
Optex
Optex VX-402 Manual de usuario
Optex
Optex FTN-RRHW Manual de usuario
Optex
Optex URX-P01 Manual de usuario
Optex
Optex FitLink Manual de usuario
Optex
Optex X-ZONE Manual de usuario
Optex
Optex FASTUS CD22-15 Series Manual de usuario
Optex
Optex FMX-DT-X5 Manual de usuario
Optex
Optex CX-702S Manual de usuario
Optex
Optex inSight INS-HX-80N Manual de usuario
Optex
Optex BX SHIELD Series Manual de usuario
Optex
Optex CX-702 MKII Manual de usuario
