One Remote Radio PL3 Manual de usuario

OneRemote Radio PL3

Advanced receiver for Bang & Olufsen BeoLab PowerLink speakers, handling

Internet Radio –Spotify

UPnP Music Player –Podcast

Installation Guide

30012013s1uk

www.oneremote.dk

ABOUT ONEREMOTE RADIO PL3

Select music or broadcasts to be handled by the OneRemote Radio PL3 via the UNDOK app on one

or more Apple or Android devices. Use either the built- in Internet Radio or stream from other

sources.

Select reproduction from a single OneRemote Radio PL3 or from several units creating a

Multiroom setup.

The OneRemote Radio PL3 is equipped with an internet streaming receiver. When receiving signals

from an internet radio station or from Spotify, streaming is directly to the Radio PL3 not involving

the control device at all. Thus, the control device does not have to be turned on or the app active

between control activities.

App control uses WiFi. Thus, the control can be carried out within the range of the WiFi, and Radio

PL3 needs not to be visible.

The OneRemote Radio PL3 has been re-built with advanced OneRemote circuitry allowing BeoLab

PowerLink speakers to be directly connected and thus creating a complete radio system.

www.oneremote.dk

Contents

ABOUT ONEREMOTE RADIO PL3 ........................................................................................................... 2

CONNECTIONS .............................................................................................................................................. 4

PowerLink Speaker Cable.................................................................................................................................................... 4

Internet Connection............................................................................................................................................................ 4

DAILY USE ...................................................................................................................................................... 4

INSTALLATION............................................................................................................................................. 5

www.oneremote.dk

CONNECTIONS

POWERLINK SPEAKER CABLE

The OneRemote Radio PL3 connects to BeoLab speakers with a PowerLink cable with 8 pin DIN

connectors. These connectors hold both the right and the left channel signals. The speakers

connect as in any other Bang & Olufsen setup in one of the two following ways:

1. One speaker connects directly to the Radio PL3 with one PowerLink cable, and the other

speaker connects to that one with a second PowerLink cable.

2. Both speakers connect separately to the Radio PL3 with their own PowerLink cable.

If the BeoLab speaker is equipped with a RJ 45 socket instead of a DIN socket, a suitable adaptor

cable must be used.

INTERNET CONNECTION

The OneRemote Radio PL3 may be internet connected either via cable or WiFi.

DAILY USE

With more than one OneRemote Radio PL3 installed a Multiroom system is established, and it is

possible to enjoy different sources in different rooms.

See the User Guide for the daily use of the OneRemote Radio PL3.

See the User Guide for creation and maintenance of program lists.

www.oneremote.dk

INSTALLATION

When delivered the OneRemote Radio PL3 is factory reset, in which condition it operates as a

WLAN Access Point, thus creating its own WiFi network.

The first step is to connect a smart phone or tablet to this network enabling connection of the

Radio PL3 to the home network.

The installation is shown with an iPhone, but the procedure for Android is similar.

The iPhone connects to the network

DigitRadio_MR1 available from the

OneRemote Radio PL3.

The Radio PL3 connects to the home

network.

Select cable or WiFi..

Wi-Fi is selected and all networks

within reach are listed.

The home network is chosen and

entering a password may be

rquired.

www.oneremote.dk

The Radio PL3 has been configured

and restarts to connect to the home

network.

The system has been configured

and is ready to use.

Press start to use my sound system.

Acquire and install the app UNDOK.

The app opens and shows available

receivers on the home network.

In this particular case one receiver

has already been named.

Select the other one named MR1

and press RENAME.

Enter a reasonable name for the

new receiver.

The receiver has been named and

the menu may be closed. The

installation has been completed.

www.oneremote.dk

The OneRemote Radio PL3 may be

used following the directions in the

User Guide.

Tabla de contenidos

Otros manuales de Receptor de One Remote

One Remote

One Remote Interface Type 2843 Manual de usuario

One Remote

One Remote 30014002 Manual de usuario

One Remote

One Remote DVBC-VI Manual de usuario

One Remote

One Remote Radio PL2 Manual de usuario

One Remote

One Remote Radio PL4 Manual de usuario

One Remote

One Remote Beo4 Guía de instalación

One Remote

One Remote Radio PL7 Manual de usuario

One Remote

One Remote Radio PL2 Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario