One Forall URC-6210 Manual de usuario
Instruction manual . . . . .P. 2
Bedienungsanleitung . .s. 10
Mode d’emploi . . . . . . .P. 18
uía del usario . . . . . . .P. 26
Manual de instruções . .P. 34
English
Deutsch
Français
Español
Português
Istruzioni per l’uso . . . .P. 42
ebruiksaanwijzing . . .P. 50
Használati útmutató
.P. 58
Inst ukcja obsługi
. . . . .P. 66
Návod k použití
.......P.74
Italiano
Nederlands
Magyar
Polski
Česky
Universal remote
Universal Fernbedienung
Télécommande universelle
Mando a Distancia Universal
Telecomando Universal
Telecomando Universale
Universele Afstandsbediening
Unive zális távvezé lő
Uniwe salny pilot zdalnego ste owania
Unive zální dálkové ovládání
URC-6210/6211
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 1
2WWW.ONEFORALL.COM
Table of Contents
INSTALLIN THE BATTERIES 3
FEATURES AND FUNCTIONS 3
SET UP
(To set up the ZAPPER for your Television)
Direct code set up 4
Search Method 6
Code Blink Out 7
SET-UP CODES
Television 82
TROUBLESHOOTIN
Helpful Hints 8
English
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 2
WWW.ONEFORALL.COM 3
Installing the batteries
The ZAPPER needs 2 new “AAAA” alkaline batteries.
1Remove the battery cover from the back of the ZAPPER by pressing down on
the tab.
2Match the batteries to the +/- marks inside the battery case, then insert the
batteries.
3Press the battery cover back into place.
Important notes:
- In order to avoid having to reprogram your ZAPPER after you
remove the batteries, you will need to insert new batteries within
5 minutes. Also, it is best that you do not use rechargeable batteries.
Features and Functions
1 POWER (red LED – Light Emitting Diode)
The POWER key operates the same function it did on your original remote
control. The LED underneath the POWER key will light up red whenever a
key is pressed.
2 CHANNEL +/-, VOLUME+/- and MUTE
The CH+/- and VOL+/- keys operate just as those on your original remote
control. These keys are also used to set up your ZAPPER.
3 MA IC
The MAGIC key (= setup key) is used to set up your ZAPPER.
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 3
4WWW.ONEFORALL.COM
Direct code set up
To set up the ZAPPER for your Television follow the instructions below.
1Find your Television code in the Set-Up Code section (page 82-101). Codes
are listed by brand name. The most popular codes are listed first.
2Make sure your TV is switched on (not on standby).
3Press and hold the MA IC key until the LED blinks twice (The LED
underneath the POWER key will blink once then twice).
4Enter your 5-digit code according to the chart below.
The LED underneath the POWER key will blink twice.
5Now, aim the ZAPPER at your Television and press POWER. If your
Television switches OFF, your ZAPPER should be ready to operate your
device.
VOLUME + = 1
VOLUME - = 2
CHANNEL - = 4MUTE = 5
CHANNEL + = 3
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 4
WWW.ONEFORALL.COM 5
6Turn your device back on and try all the remote’s functions to ensure they
are working properly. If the functions do not work properly, repeat steps
1-5 using another code listed under your brand.
For example: To enter a Sony TV code 33121, you would press CHANNEL +,
CHANNEL +, VOLUME +, VOLUME -, VOLUME +.
If your television does not respond to the ZAPPER after you have
tried all the codes listed for your brand, try the Search Method
described on page 6.
Make sure you write your correct 5 digit code in
the boxes provided on this page.
Important notes:
- Some codes are quite similar. If your television does not respond or
is not functioning properly with one of the codes, follow steps 1-5
with each code listed for your brand.
- If none of the codes listed for your brand operate your television,
follow the Search Method described in the next section. The Search
Method can be used even if your brand is not listed at all.
- Write the code for your TV in the boxes provided below for easy
future reference.
TV Code
■
■
■
■
■
■
■
■
■
■
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 5
6WWW.ONEFORALL.COM
Search Method
If your Television does not respond to the ZAPPER after trying all the codes
listed for your brand, try searching for your code. To search for your TV code:
1 Turn on your TV.
2Press and hold the MA IC key until the LED blinks twice
(The LED underneath the POWER key will blink once then twice).
3Next, press the MUTE, CHANNEL -, CHANNEL -.
4 Point the ZAPPER at your television. Next, alternate between POWER and
CHANNEL - until your Television turns off. You may have to press these
keys many times (up to 150!), so please be patient. Remember, you must
aim the ZAPPER at your device the entire time you are searching for your
code.
5 When your device turns off, press and release MA IC to store the code.
The ZAPPER should now be ready to operate your Television. Turn your
device back on and try all the remote’s functions to ensure they are
working properly. If some of the ZAPPER’S commands are not operating
correctly, try the search method again, you may be using the wrong code.
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 6
WWW.ONEFORALL.COM 7
Code Blink Out
After you have used the Search Method, you can find out which code
the ZAPPER responded to by blinking back the code. It’s handy to know
your Television code for future reference. Remember, you can only
blink back your code after the ZAPPER is operating your device.
To blink out your TV code:
1Press and hold the MA IC key until the red LED blinks twice (the LED
underneath the POWER key will blink once then twice).
2 Next, press MUTE, CHANNEL -, CHANNEL +.
3 For the first digit of your 5-digit code, press VOLUME + and count the
red blinks.
4For the second digit, press VOLUME - and count the red blinks.
5For the third digit, press CHANNEL + and count the red blinks.
6 For the fourth digit, press CHANNEL - and count the red blinks.
7For the fifth digit, press MUTE and count the red blinks.
Write the code for your TV in the boxes provided on page 5.
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 7
8WWW.ONEFORALL.COM
Problem:
Your brand is not listed in
the ONE FOR ALL code section?
The ONE FOR ALL does not
operate your television?
The ONE FOR ALL is not
performing commands
properly?
You cannot reach channel 10
and above on your TV.
The ONE FOR ALL does not
respond after pressing a key?
LED does not blink when you
press a key?
Solution:
Try the search method.
A) Try all the codes listed for your
brand.
B) Try the search method.
You may be using the wrong code.
Try Direct Set-Up again trying each
code listed under your brand or
start the search method over again
to locate the proper code.
If your original remote did not
have CHANNEL +/- keys, the ZAPPER
may not operate this function.
Make sure you are using new
batteries and are aiming the ONE
FOR ALL at your device.
Replace batteries with 2 new
“AAAA” alkaline batteries.
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 8
WWW.ONEFORALL.COM 9
Customer Service
In the UK
E-mail : ofahelp@uebv.com (*)
Fax : +31 53 432 9816
Tel. : 0901-5510010 (£ 0,50 per minute)
In Ireland In Australia
E-mail : ofahelp@uebv.com (*) E-mail : ofahelp@uebv.com (*)
Fax : +31 53 432 9816 Fax : 03 9672 2479
Tel. : 016015986 Tel. : 1 300 888 298
In South Africa In New Zealand
Fax : 011 298 2302 Fax : (06) 878 2760
Tel. : 0860 100551 Tel. : 0508 ONE 4 ALL (663 4 255)
Tel. : 011 298 2300
(*) Just send a blank message, you’ll get auto-reply.
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:46 Pagina 9
82 WWW.ONEFORALL.COM
TV
888 13135 14233
A.R. Systems 15322 13555
Accent 11233 15322
Acer 31435
Acura 11125
Adcom 21111
Addison 21214 11524
Admiral 11444 12234 14244
11433 13135
Advent 23112
Adyson 12443 12442
AEG 15522
Agashi 12442 12443
AGB 15142
Agef 11433
Aim 11233 15322
Aiwa 21421 21412 41242
41224 33121
Akai 11125 13532 12424
15322 11233 13552
14324 12342 12444
13245 11353 12234
14233 21435 15142
21515 21253 21441
33233 15513 22114
15254 21551 14521
12443 21122 12442
13135 12314 14113
15522 24233 41224
14454 21154 25554
41331
Akiba 12444 13223 14421
11233 15322 13245
Akira 14244
Akito 13153
Akura 12444 13135
Alaron 12442
Alba 11125 11233 15322
11232 12444 13552
21244
Alfide 21253
Allorgan 13245 12443
Allstar 11233 15322
Amplivision 12443
Amstrad 11125 11233 15142
13135 13533 13552
12444 14233 14324
15322 24233 21154
31355 41523
Anam 11125 22532
Anam National 21211
Andersson 25234 25155
Anglo 11125 13135
Anitech 11125 13135 11233
15322 13223
Ansonic 13551 11233 15322
11125 21244 13555
12234 13243 14232
12553
AOC 11125 11331 11444
11524 12314
Aolingpike 13135 14233
Apollo 14454
Arcam 12442 12443
Ardem 14532 11233 15322
Arena 11233
706113_URC-6210-11_E_10t:Zapper_3 08-05-2007 09:47 Pagina 82
Otros manuales para URC-6210
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Control remoto universal de One Forall
One Forall
One Forall URC-7740 Manual de usuario
One Forall
One Forall URC-6532 Manual de usuario
One Forall
One Forall URC-7930 Manual de usuario
One Forall
One Forall URC-8350 Manual de usuario
One Forall
One Forall Topline Manual de usuario
One Forall
One Forall URC 7980 Manual de usuario
One Forall
One Forall URC-7562 Manual de usuario
One Forall
One Forall Zapper URC-6520 Manual de usuario
One Forall
One Forall URC-7780 Manual de usuario
One Forall
One Forall OFA Kameleon URC-6690 Manual de usuario
One Forall
One Forall URC-7711 Manual de usuario
One Forall
One Forall URC-6211 Manual de usuario
One Forall
One Forall URC8820N Manual de usuario
One Forall
One Forall OARC05G Manual de usuario
One Forall
One Forall Easy 2 Manual de usuario
One Forall
One Forall URC-7532 Manual de usuario
One Forall
One Forall URC 3050 Manual de usuario
One Forall
One Forall URC-6420 Guía del administrador
One Forall
One Forall URC-7710 Manual de usuario
One Forall
One Forall A/V Producer URC 8800 Manual de usuario
