Omron E5C2 Manual de usuario

Analogue Temperature Controller E5C2 I-7

Temperature

Controller

Analogue Temperature Controller

E5C2

DIN-sized (48 x 48 mm) Temperature

Controller with Analog Setting

• Compact, low-cost Temperature Controller.

• Incorporates proportional control and reset adjustment function.

• Consecutive mounting possible using mounting adapter.

• Incorporates a plug-in socket, thus allows to DIN-track and flush

mounting.

Model Number Structure

■Model Number Legend

1. Model name

2. Control output

R: Relay

Q: Voltage

3. Control method

20: ON-OFF control

40: P control

4. Input type

K: K-type thermocouple

L: J-type thermocouple

P: Platinum resistance thermometer (PT100)

G: Thermistor (THE)

5. Special type

Blank: Standard type

D, DIN: Special types

Ordering Information

■Temperature Controllers

Note: When placing an order, specify the standard temperature range and supply voltage in addition to the model number.

(e.g., E5C2-R20K 0°C to 200°C100/110 VAC)

■Accessories (Order Separately)

12345

E5C2- @@@@

Setting

method Indication

method Control mode Output Model

Thermocouple Platinum resistance

thermometer

Pt100

Thermistor

THE

K (CA)

Chromel vs.

alumel

L (IC)

Iron vs.

constantan

Analog setting No indication ON/OFF Relay E5C2-R20K

E5C2-R20L-D

E5C2-R20P-D E5C2-R20G

P Relay E5C2-R40K

E5C2-R40L-D

E5C2-R40P-D ---

Name Model

Front Connecting Socket P2CF-08

Back Connecting Socket (for flush mounting) P3G-08

Front Connecting Socket with Finger Protection P2CF-08-E

Protective Cover (for finger protection) Y92A-48G

I-8 Analogue Temperature Controller E5C2

Specifications

■Ratings

Note: Specify either 100/110/120 VAC or 200/220/240 VAC when ordering.

■Input Ranges

Note: 1. Values in ( ) are the minimum unit.

2. Values in ( ) are the thermistor resistive value.

■Characteristics

Note: 1. No reset function is incorporated by any E5C2 model with ON/OFF control.

2. The model number of the special watertight cover conforming to IP66, NEMA4 is Y92A-48B.

Supply voltage 100/110/120 VAC (common), 200/220/240 VAC (common) (See note.)

50/60 Hz (common)

Operating voltage range 90% to 110% of rated supply voltage

Power consumption Approx. 2 VA

Input Thermocouple (with sensor burnout detection circuit), platinum resistance thermometer, or thermistor

Control mode ON/OFF or P control

Setting method Analog setting

Indication method No indication

Control output Relay output: SPDT, 3 A at 250 VAC, resistive load (switching capacity: 330 VA)

Input Thermocouple Platinum resistance

thermometer Thermistor (see note 2)

K (CA)

Chromel vs. alumel L (IC)

Iron vs. constantan Pt100 THE

Range °C0 to 200 (5),

0 to 300 (10),

0 to 400 (10),

0 to 600 (20),

0 to 800 (20),

0 to 1,000 (25),

0 to 1,200 (25)

0 to 200 (5),

0 to 300 (10),

0 to 400 (10)

–50 to 50 (2),

–20 to 80 (2),

0 to 50 (1),

0 to 100 (2),

0 to 200 (5),

0 to 300 (10),

0 to 400 (10)

–50 to 50 (2) (6 kΩat 0°C),

0 to 100 (2) (6 kΩat 0°C),

50 to 150 (2) (30 kΩat 0°C)

°F32 to 392 (10),

32 to 572 (20),

32 to 752 (20),

32 to 1,112 (40),

32 to 1,472 (50),

32 to 1,832 (50),

32 to 2,192 (50)

32 to 392 (10),

32 to 572 (20),

32 to 752 (20)

32 to 212 (5),

32 to 392 (10)

---

Setting accuracy ±2% FS max.

Hysteresis Approx. 0.5% FS (fixed)

Proportional band 3% FS (fixed)

Control period Approx. 20 s

Reset range (see note 1) 5 ±1% FS min.

Insulation resistance 20 MΩmin. (at 500 VDC)

Dielectric strength 2,000 VAC, 50/60 Hz for 1 min between charged terminals and uncharged metallic parts

Vibration resistance Malfunction: 10 to 55 Hz, 0.15-mm single amplitude for 10 min each in X, Y, and Z directions

Destruction: 16.7 Hz, 2-mm double amplitude for 2 hrs each in X, Y, and Z directions

Shock resistance Malfunction: 147 m/s2, 3 times each in 6 directions

Destruction: 294 m/s2, 3 times each in 6 directions

Life expectancy Electrical: 100,000 operations min. (3 A at 110 VAC, resistive load)

Ambient temperature Operating: –10°C to 55°C (with no icing or condensation)

Ambient humidity Operating: 45% to 85%

Degree of protection Front panel: IEC standard IP40 (see note 2)

Terminals: IEC standard IP00

Weight Approx. 200 g (with flush-mounting adapter)

Analogue Temperature Controller E5C2 I-9

Temperature

Controller

Nomenclature

Operation Indicator

Dimensions

Note: All units are in millimeters unless otherwise indicated.

Temperature setting knob

Operation indicator

RESET adjustment shaft

No reset function is incorporated by any

E5C2 model with ON/OFF control.

Indicator Output

Red Lit ON

Not lit OFF

93+1

0 141+1

0 189+1

0 237+1

0 285+1

N23456

48 x 48

44.8 x 44.8

Panel Cutout

Note: 1. Recommended panel thickness is 1 to 4 mm.

2. Close side-by-side mounting is possible (in a single direction).

Panel

Y92F-30 Flush-mounting adapter

Tightening screw

(96) (see note)

Note: 109 mm for US08 Back Connecting Socket

Terminal Arrangement

(Bottom View)

Dimensions with Flush-mounting Adapter (Accessory),

and Back Connecting Socket (Sold Separately)

Flush-mounting

adapter P3G-08 Back con-

necting socket

Side-by-side Mounting

of N Controllers

60 min.

I-10 Analogue Temperature Controller E5C2

Accessories (Order Separately)

Protective Cover Y92A-48

The protective cover protects the front panel, particularly the setting

section, against dust, dirt, and water drip. It also prevents the set val-

ues from being altered due to accidental contact with the setting

keys.

Installation

■Connections

Input

Connect a thermocouple, the E52-THE@Thermistor or platinum

resistance thermometer to the E5C2 as shown in the following illus-

tration.

Output

If the load circuit is a heating control system, be sure to connect the

load to terminals 4 and 5. If the load circuit is a cooling control sys-

tem, be sure to connect the load to terminals 4 and 6. If the heating

control system is connected to terminals 4 and 6 or the cooling con-

trol system is connected to terminals 4 and 5, the temperature of the

heating control system or cooling control system will be abnormal

and a serious accident may result.

If the E5C2 is in frequent operation, such as proportional operation,

add an appropriate external relay to the E5C2 by considering the

capacity of the load and the life of the relay.

Power Supply

If a single power supply is used for the E5C2 and the load, the supply

voltage of the power supply may vary greatly when the load is open

or closed if the capacity of the power supply is not large enough.

Make sure that the capacity of the power supply is large enough so

that the supply voltage range will be always from 90% to 110% of the

rated supply voltage.

The E5C2 operates at either 50 or 60 Hz.

P2CF-08 Front Connecting Socket

Mounting Holes

70 max.

Eight, M3.5 x 7.5 sems

50 max.

20 max.

Two, 4.5 dia. or Two, M4

P3G-08 Back Connecting Socket (for Flush Mounting)

27 dia.

Two,

4.5-dia.

holes

Terminal Arrangement/

Internal Connections

(Top View)

Note: Can also be

mounted to a

DIN track.

Terminal Arrangement/

Internal Connections

(Bottom View)

Note: A finger-protection model (P2CF-08-E) is also available.

Note: A Protective Cover for fin

rotection

(

Y92A-48G

)

is also available.

Appearance

Model Y92A-48B

Thermocouple input

Relay output

Thermistor input

Platinum resistance

thermometer input

Power supply

100/110, 200/220,

110/120, 220/240 VAC

50/60 Hz

Analogue Temperature Controller E5C2 I-11

Temperature

Controller

Precautions

Mounting

Track Mounting (E5C2 with P2CF-08)

When mounting two or more E5C2 models with track-mounting sock-

ets, leave a space of approximately 20 mm on both sides of the sock-

ets where hooks are located.

Flush Mounting

Insert E5C2 into the square hole of the panel and insert an adapter

from the back so that there will be no space between E5C2 and the

panel. Then, secure the E5C2 with a screw.

The P3G-08 can be wired in the same way as the P2CF-08.

Dismounting

If flush mounted, loosen the screw of the adapter and disengage the

hooks for dismounting.

Temperature Setting

Do not turn the temperature setting knob of the E5C2 with excessive

force, otherwise the stopper of the knob may break.

Others

Do not remove the housing of the E5C2, otherwise the housing may

break.

To clean the surface of the E5C2, use a soft cloth wet with neutral

detergent or alcohol. Do not use any organic solvent, such as paint

thinner or benzine, strong acid or strong alkali to clean the surface of

the E5C2, otherwise the surface of the E5C2 will become damaged.

P2CF-08

Panel

Hook

Duct

Tightening screw

I-12 Analogue Temperature Controller E5C2

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Cat. No. H081-E1-02

Tabla de contenidos

Otros manuales de Controladores de temperatura de Omron

Omron

Omron E5CD-B Manual de usuario

Omron

Omron E5CC-B-800 Manual de usuario

Omron

Omron E5CSV - Manual de usuario

Omron

Omron CJ Series Manual de usuario

Omron

Omron E5ZE-8 D1 B-V2 Manual de usuario

Omron

Omron E5CD-800 Manual de usuario

Omron

Omron EJ1 EtherCAT Manual de usuario

Omron

Omron E5CN Manual de usuario

Omron

Omron E5ZN-SCT Manual de usuario

Omron

Omron E5CSV - Manual de usuario

Omron

Omron CELCIUX Manual de usuario

Omron

Omron E5CS Manual de usuario

Omron

Omron E5CC Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

Omron

Omron E5AN-H Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

Omron

Omron E5GN Manual de usuario

Omron

Omron E5 D Series Manual de uso y cuidado

Omron

Omron E5*N Series Guía de instalación

Omron

Omron E5C series Manual de usuario

Omron

Omron E5 N H - Manual de lista de piezas

Omron

Omron E5DC Manual de usuario

Omron

Omron E5ZN-DRT Manual de usuario

Omron

Omron E5C-T Series Manual de uso y cuidado

Manuales populares de Controladores de temperatura de otras marcas

Swegon

Swegon LUNAd MB Manual de usuario

Lucky Reptile

Lucky Reptile Thermo Control II Manual de usuario

SENSORMETRIX

SENSORMETRIX Argon 100 Manual de usuario

Fuji Electric

Fuji Electric PXE4 Manual de usuario

Yuyao gongyi

Yuyao gongyi XMT-808 series Manual de usuario

Selec

Selec TC544C Manual de usuario

P.W. KEY

P.W. KEY rt-208gt Manual de usuario

Future Design

Future Design FDC-9200 Manual de usuario

BH Thermal

BH Thermal BriskONE Manual de usuario

West Control Solutions

West Control Solutions KS 45 Guía de inicio rápido

MCS

MCS RITC-15B Manual de usuario

SMC Networks

SMC Networks Thermo-con INR-244-639 Manual de usuario

eltherm

eltherm Ex-TC It Series Manual de usuario

industrie technik

industrie technik CA1 Manual de usuario

KRAL

KRAL EET 32 Manual de usuario

dixell

dixell XR420C Diagrama de cableado

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Manual de usuario

Vaillant

Vaillant VR 92/3 Manual de usuario