Omron CJ Series Manual de instrucciones

OMRON Corporation

NX-series

EtherNet/IP Coupler Unit

CJ Series

EtherNet/IPTM Connection Guide

P656-E1-01

About Intellectual Property Rights and Trademarks

Microsoft product screen shots reprinted with permission from Microsoft Corporation.

Windows is a registered trademark of Microsoft Corporation in the USAand other countries.

ODVA and EtherNet/IPTM are trademarks of ODVA.

Sysmac is a trademark or registered trademark of OMRON Corporation in Japan and other

countries for OMRON factory automation products.

Company names and product names in this document are the trademarks or registered

trademarks of their respective companies.

Table of Contents

1. Related Manuals.......................................................................................... 1

2. Terms and Definitions................................................................................. 2

3. Precautions.................................................................................................. 3

4. Overview ...................................................................................................... 4

5. Applicable Devices and Device Configuration........................................ 5

5.1. Applicable Devices.............................................................................. 5

5.2. Device Configuration........................................................................... 6

6. EtherNet/IP Settings.................................................................................... 8

6.1. Parameters.......................................................................................... 8

6.2. Slave Terminal Configuration .............................................................. 8

6.3. Tag Data Link Settings......................................................................... 9

7. EtherNet/IP Connection Procedure......................................................... 10

7.1. Work Flow.......................................................................................... 10

7.2. Slave Terminal Setup......................................................................... 12

7.3. PLC Setup ......................................................................................... 21

7.4. Network Settings ............................................................................... 30

7.5. EtherNet/IP Communication Status Check....................................... 42

8. Initialization Method.................................................................................. 48

8.1. Initializing PLC................................................................................... 48

8.2. Initialization of Slave Terminal........................................................... 49

9. Revision History........................................................................................ 50

．

Related Manuals

1. Related Manuals

To ensure system safety, make sure to always read and follow the information provided in all

Safety Precautions and Precautions for Safe Use in the manuals for each device which is

used in the system.

Cat. No.

Model

Manual name

W472

CJ2M-CP[][]

CJ2H-CPU6[]

CJ2H-CPU6[]-EIP

CJ-series

CJ2 CPU Unit

Hardware USER'S MANUAL

W473

CJ2M-CPU[][]

CJ2H-CPU6[]

CJ2H-CPU6[]-EIP

CJ-series

CJ2 CPU Unit

Software USER'S MANUAL

W465

CJ1W-EIP21

CJ2M-CPU3[]

CJ2H-CPU6[]-EIP

CJ Series

EtherNet/IPTM Units

OPERATION MANUAL

W446

CXONE-AL[][]C-V4

/ AL[][]D-V4

CX-Programmer

OPERATION MANUAL

0969584-7

W4S1-05[]

W4S1-03B

Switching Hub

W4S1-series

Users Manual

W504

SYSMAC-SE2[][][]

Sysmac Studio Version 1

Operation Manual

W536

NX-EIC[][][]

NX-series

EtherNet/IPTM Coupler Unit

User’s Manual

W521

NX-ID[][][][]

NX-IA[][][][]

NX-OC[][][][]

NX-OD[][][][]

NX-MD[][][][]

NX-series

Digital I/O Units

User’s Manual

W522

NX-AD[][][][]

NX-DA[][][][]

NX-TS[][][][]

NX-series

Analog I/O Units

User’s Manual

W523

NX-PD1[][][]

NX-PF0[][][]

NX-PC0[][][]

NX-TBX01

NX-series

System Units

User’s Manual

W540

NX-CIF[][][]

NX-series

Communications Interface Units

User’s Manual

W524

NX-EC0[][][]

NX-ECS[][][]

NX-PG0[][][]

NX-series

Position Interface Units

User’s Manual

Z930

NX-SL[][][][]

NX-SI[][][][]

NX-SO[][][][]

NX-series

Safety Control Unit

User’s Manual

．

Terms and Definitions

2. Terms and Definitions

Term Explanation and Definition

Node

Aprogrammable controller and a device are connected to an EtherNet/IP

network via EtherNet/IP ports. EtherNet/IP recognizes each EtherNet/IP

port connected to the network as one node.

When a device with two EtherNet/IP ports is connected to the

EtherNet/IP network, EtherNet/IP recognizes this device as two nodes.

EtherNet/IP achieves the communications between programmable

controllers or the communications between a programmable controller

and a device by exchanging data between these nodes connected to the

network.

Tag

Aminimum unit of the data that is exchanged on the EtherNet/IP network

is called a tag. The tag is defined as a network variable or as a physical

address, and it is assigned to the memory area of each device.

Tag set In the EtherNet/IP network, a data unit that consists of two or more tags

can be exchanged. The data unit consisting of two or more tags for the

data exchange is called a tag set. Up to eight tags can be configured per

tag set for the programmable controllers produced by OMRON

Corporation.

Tag data link In EtherNet/IP, the tag and tag set can be exchanged cyclically between

nodes without using a user program.

This standard feature on EtherNet/IP is called a tag data link.

Connection A connection is used to exchange data as a unit within which data

concurrency is maintained. The connection consists of tags or tag sets.

Creating the concurrent tag data link between the specified nodes is

called a "connection establishment".When the connection is established,

the tags or tag sets that configure the connection are exchanged

between the specified nodes concurrently.

Connection type There are two kinds of connection types for the tag data link connection.

One is a multi-cast connection, and the other is a unicast (point-to-point)

connection. The multi-cast connection sends an output tag set in one

packet to more than one node. The unicast connection separately sends

one output tag set to each node. Therefore, multi-cast connections can

decrease the communications load if one output tag set is sent to more

than one node.

Originator and

Target To operate tag data links, one node requests the opening of a

communications line called a "connection".

The node that requests to open the connection is called an "originator",

and the node that receives the request is called a "target".

Tag data link

parameter Atag data link parameter is the setting data to operate tag data links.

It includes the data to set tags, tag sets, and connections.

．

Precautions

3. Precautions

(1) Understand the specifications of devices which are used in the system. Allow some

margin for ratings and performance. Provide safety measures, such as installing a safety

circuit, in order to ensure safety and minimize the risk of abnormal occurrence.

(2) To ensure system safety, make sure to always read and follow the information provided in

all Safety Precautions and Precautions for Safe Use in the manuals for each device

which is used in the system.

(3) The user is encouraged to confirm the standards and regulations that the system must

conform to.

(4) It is prohibited to copy, to reproduce, and to distribute a part or the whole of this

document without the permission of OMRON Corporation.

(5) The information contained in this document is current as of July 2016. It is subject to

change for improvement without notice.

The following notations are used in this document.

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury or property damage.

Precautions for Correct Use

Precautions on what to do and what not to do to ensure proper operation and performance.

Additional Information

Additional information to read as required.

This information is provided to increase understanding or make operation easier.

Symbol

The triangle symbol indicates precautions (including warnings).

The specific operation is shown in the triangle and explained in the text.

This example indicates a general precaution.

The filled circle symbol indicates operations that you must do.

The specific operation is shown in the circle and explained in the text.

This example shows a general precaution for something that you must do.

．

Overview

4. Overview

This document describes the procedures for connecting NX-series EtherNet/IP Coupler Unit

(hereinafter referred to as Coupler Unit) + NX-series various types of Units to CJ-series

Programmable Controller + EtherNet/IP Unit (hereinafter referred to as PLC) via EtherNet/IP,

both produced by OMRON Corporation (hereinafter referred to as OMRON), and for checking

their communication status.

In this document, the connection status is checked with an EtherNet/IP slave (hereinafter

referred to as Slave Terminal) that is created by mounting I/O Units to Coupler Unit.

Refer to Section 6. EtherNet/IP Settings and Section 7. EtherNet/IP Connection Procedure to

understand setting methods and key points to operate EtherNet/IP tag data links.

In this document, CJ-series EtherNet/IP Unit and the built-in EtherNet/IP port of CJ-series CJ2

CPU Unit are collectively called as "EtherNet/IP Unit''.

．

Applicable Devices and Device Configuration

5. Applicable Devices and Device Configuration

5.1. Applicable Devices

The applicable devices are as follows:

Manufacturer

Name

Model

OMRON

CJ2 CPU Unit

CJ2[]-CPU[][]

OMRON

EtherNet/IP Unit

CJ1W-EIP21

CJ2H-CPU6[]-EIP

CJ2M-CPU3[]

OMRON

NX-series

EtherNet/IP

Coupler Unit

NX-EIC[][][]

OMRON

NX-series Units

DC Input Unit

AC Input Unit

Relay Output Unit

Transistor Output Unit

Digital Mixed I/O Unit

Analog Input Unit

Analog Output Unit

Temperature Input Unit

Heater Burnout Detect Unit

Communications Interface Unit

System Unit

Load Cell Input Unit

Incremental Encoder Input Unit

SSI Input Unit

Pulse Output Unit

Safety CPU Unit

Safety Input Unit

Safety Output Unit

NX-ID[][][][]

NX-IA[][][][]

NX-OC[][][][]

NX-OD[][][][]

NX-MD[][][][]

NX-AD[][][][]

NX-DA[][][][]

NX-TS[][][][]

NX-HB[][][][]

NX-CIF[][][]

NX-PC0[][][]

NX-RS[][][][]

NX-EC0[][][]

NX-ECS[][][]

NX-PG0[][][]

NX-SL[][][][]

NX-SI[][][][]

NX-SO[][][][]

Precautions for Correct Use

In this document, the devices with models and versions listed in 5.2. Device Configuration are

used as examples of applicable devices to describe the procedures for connecting the

devices and checking their connections.

You cannot use devices with versions lower than the versions listed in 5.2.

To use the above devices with models not listed in 5.2. or versions higher than those listed in

5.2., check the differences in the specifications by referring to the manuals before operating

the devices.

Additional Information

This document describes the procedures for establishing the network connections.

It does not provide information on operation, installation, wiring method, device functionality,

or device operation, which is not related to the connection procedures.

Refer to the manuals or contact your OMRON representative.

．

Applicable Devices and Device Configuration

5.2. Device Configuration

The hardware components to reproduce the connection procedures in this document are as

follows:

Manufacturer

Name

Model

Version

OMRON

CJ2 CPU Unit

(Built-in EtherNet/IP port)

CJ2M-CPU32

Ver.2.0

(Ver.2.12)

OMRON

Power Supply Unit

CJ1W-PA202

OMRON

Switching hub

W4S1-05C

Ver.1.00

24 VDC power supply

(for Switching hub)

OMRON

CX-One

CXONE-AL[][]C-V4

/AL[][]D-V4

Ver.4.[][]

OMRON

CX-Programmer

(Included in CX-One)

Ver.9.60

OMRON

Network Configurator

(Included in CX-One)

Ver.3.59a

Personal computer (OS: Windows 7)

USB cable

(USB 2.0 type B connector)

LAN cable (STP (shielded,

twisted-pair) cable of Ethernet

category 5 or higher)

OMRON

Coupler Unit

NX-EIC202

Ver.1.0

OMRON

Digital Input Unit (DC Input Unit)

NX-ID4442 Ver.1.0

OMRON

Digital Output Unit

(Transistor Output Unit)

NX-OD3256 Ver.1.0

OMRON

Analog Input Unit (Voltage Input Unit)

NX-AD2603

Ver.1.0

OMRON

Sysmac Studio

SYSMAC-SE2[][][] Ver.1.15

24 VDC power supply

(Unit power supply)

24 VDC power supply

(I/O power supply)

USB cable

CJ2M-CPU32

(Built-in EtherNet/IP port)

USB cable

Personal computer

(CX-One and

Sysmac Studio

installed,

OS: Windows 7)

24 VDC power supply

LAN cable

W4S1-05C

Slave Terminal

-EIC202＋

-ID4442＋

-OD3256＋

-AD2603

24 VDC power supply

(Unit power supply)

24 VDC power supply

(I/O power supply)

．

Applicable Devices and Device Configuration

Precautions for Correct Use

Update CX-Programmer and Network Configurator to the versions specified in this Clause

5.2. or to higher versions. If you use a version higher than the one specified, the procedures

and related screenshots described in Section 7. and subsequent sections may not be

applicable. In that case, use the equivalent procedures described in this document by

referring the CX-Programmer OPERATION MANUAL (Cat. No. W446) and Network

Configurator Online Help.

Precautions for Correct Use

Update Sysmac Studio to the version specified in this Clause 5.2. or to a higher version.

If you use a version higher than the one specified, the procedures and related screenshots

described in Section 7. and subsequent sections may not be applicable. In that case, use the

equivalent procedures described in this document by referring to the Sysmac Studio Version

1 Operation Manual (Cat. No. W504).

Additional Information

For specifications of 24 VDC power supply available for Switching hub, refer to the Switching

Hub W4S1-series Users Manual (Cat. No. 0969584-7).

Additional Information

For specifications of 24 VDC power supply (unit power supply and the I/O power supply),

refer to the NX-series EtherNet/IPTM Coupler Unit User’s Manual (Cat. No. W536).

Additional Information

The system configuration in this document uses USB for the connection between Personal

computer and PLC. For information on how to install the USB driver, refer to A-5 Installing the

USB Driver of the CJ-series CJ2 CPU Unit Hardware User's Manual (Cat. No. W472).

Additional Information

The system configuration in this document uses USB for the connection between Personal

computer and Coupler Unit. For information on how to install the USB driver, refer to A-1

Driver Installation for Direct USB Cable Connection in Appendices of the Sysmac Studio

Version 1 Operation Manual (Cat. No. W504).

Otros manuales para CJ Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Omron

Omron

Omron SYSMAC CJ1W-EIP21 Manual de usuario

Omron

Omron FLOW EM2100 Manual de usuario

Omron

Omron 3G3AX-MX2-PRT-E Manual de usuario

Omron

Omron ITBC-CST01 - 09-2000 Manual de usuario

Omron

Omron E3Z series Manual de instrucciones

Omron

Omron SYSMAC CS1W-ETN21 Manual de usuario

Omron

Omron 3G3MV-P10CDT-E Manual de usuario

Omron

Omron NX Series Manual de instrucciones

Omron

Omron WD30-ME Manual de usuario

Omron

Omron CQM1H-SCB41 Manual de usuario

Omron

Omron EJ1 - 07-2008 Manual de usuario

Omron

Omron G70A Manual de usuario

Omron

Omron SYSMAC CS1W-SCB41-V1 Manual de usuario

Omron

Omron J7MN - Manual de usuario

Omron

Omron CS CJ1W-ETN21 Manual de usuario

Omron

Omron ERT1 Series Manual de usuario

Omron

Omron E3X-DRT21-S Manual de usuario

Omron

Omron J7KNA - Manual de usuario

Omron

Omron CS Series Manual de usuario

Omron

Omron E2E series Manual de instrucciones

Omron

Omron DEVICENET SAFETY - 03-2008 Manual de usuario

Omron

Omron 3G3MV-PDRT2 Manual de usuario

Omron

Omron DeviceNet DRT2-ROS16 Manual de usuario

Omron

Omron DEVICENET - Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario