Omron SPINOGY 3G3MX2 Manual de usuario

Quick Start Guide 3G3MX2

spinogy.de

Index

General remarks

01.1 Notice

01.2 Limitaton of liability

01.3 Product name

01.4 Labeling of the frequency inverter MX2

Technical description

02.1 Product overview

02.2 Technical data

02.3 Construction of the 3G3MX2

Installation

03.1 Assembly of the 3G3MX2

03.2 Installation/ removal method of the terminal block cover

03.3 Wiring of 3G3MX2

03.4 Wiring of the SPINOGY X22 to the MX2

Commissioning

04.1 Power-up test

04.2 Using the front panel keypad

04.3 Function groups of the parameters

04.4 Keypad navigation map

04.5 Important parameters

04.5 First operation of the spindle

Troubleshooting

05.1 Error codes

05.2 Restoring factory settings

01 General remarks

01.1 Notice

This document is only a quick start guide for the MX2 frequency inverter, and therefore it has no claim to be

complete. The document is only intended for the proper commissioning of the frequency inverter. The safety

instructions can be found in the MX2 operating manual.

01.2 Limitation of liability

SPINOGY doesn’t assume liability for personal injuries, material damages, damages caused to the device and

consequential damages caused by failure to follow this quick start guide, improper use of the device, repairs or

any other actions done by non-qualified workers on the device or damages on this unit occur or occurred by

using unauthorized non-approved spare parts.

01.3 Product name

This quick start guide is intended for the spindles of the following type:

Product name:

3G3MX2

01.4 Labeling of the frequency inverter MX2

The Omron MX2 inverters are equipped with product labels on the right side of the housing, as pictured below.

It must be ensured that the technical data on the label is compatible to the network supply and the safety

requirements of the application.

02 Technical description

02.1 Product overview

Input

Type

ND-mode

HD-Mode

Rated

current (A)

Motor output

(kW)

Rated

current (A)

Motor output

(kW)

1 x 230 V

MX2-AB007

6,0

1,1

5,0

0,75

MX2-AB015

9,6

2,2

8,0

1,5

MX2-AB022

12,0

3,0

11,0

2,2

3 x 400 V

MX2-A4004

2,1

0,75

1,8

0,4

MX2-A4007

4,1

1,5

3,4

0,75

MX2-A4015

5,4

2,2

4,8

1,5

MX2-A4022

6,9

3,0

5,5

2,2

MX2-A4030

8,8

4,0

7,2

3,0

MX2-A4040

11,1

5,5

9,2

4,0

MX2-A4055

17,5

7,5

14,8

5,5

MX2-A4075

23,0

11,0

18,0

7,5

02.2 Technical data

Item

General specifications

Protective housing

IP20

Control method

Sinusoidal Pulse Width Modulation (PWM) control

Carrier frequency

2 kHz to 15 kHz (derating required depending on the model)

Output frequency range

0,1 to 1000 Hz

Frequency accuracy

Digital command: 0.01% of the maximum frequency

Analog command: 0.2% of the maximum frequency (25°C ±10°C)

Frequency setting

resolution

Digital: 0,01 Hz; Analog: max. Frequenz/400

Volt./Freq. characteristic

V/f control (constant torque, reduced torque, free-V/F): base freq. 30 Hz to1000

Hz adjustable

Sensorless vector control, Closed loop control with motor encoder feedback:

base freq. 30 Hz ~ 400 Hz adjustable

Overload capacity

Dual rating: HD (heavy duty) : 60 s @ 150 %

ND (Normal duty) : 60 s @120 %

Acceleration/deceleration

time

0.01 to 3600 seconds, linear and S-curve accel/decel,2. Einstellung für second

accel/decel setting available

Starting torque

200 % @ 0,5 Hz (sensorless vector control)

Input signal

Freq. setting

Operator panel

Up and Down keys / Value settings

External signal

0 to 10 VDC (input impedance 10 k

Ohms), 4 to 20 mA (input impedance

100 Ohms), Potentiometer (1 k to 2 k

Ohms, 2 W)

Via network

RS485 ModBus RTU, other network

option

FWD/REV run

Operator panel

Run/Stop (Forward/Reverse run

change by command)

External signal

Forward run/stop, Reverse run/stop

Via network

RS485 ModBus RTU, other network

option

Intelligent input terminal

Seven terminals, sink/source

02 Technical description

changeable by a short bar

68 functions assignable

Output signal

Intelligent output terminal

48 functions assignable

Monitor output (analog)

Pulse train output

(0~10 Vdc, 32 kHz max.)

Alarm output contact

ON for inverter alarm (1c contacts, both normally open or closed available.)

Operating environment

Temperature

Operating (ambient): -10 to 50°C /

Storage: -20 to 65°C

Humidity

20 to 90% humidity (non-condensing)

Vibration

5,9 m/s2 (0,6 G), 10 to 55 Hz

Location

Altitude 1,000m or less, indoors (no

corrosive gasses or dust)

02.3 Construction of the 3G3MX2

The following figure shows the basic structure of the 3G3MX2 frequency inverter.

02 Technical description

The following figure shows the designation of the parts inside the terminal block cover.

Name

Description

Modbus-RTU

Termination resistor

selector switch

Use this Terminal Resistor selector switch for RS-485 terminals on the control

circuit terminal

block. When this switch is turned ON, the internal 200 Resistor is connected.

Safety function selector

switch

Turn this switch ON when using the safety function. Turn OFF the power before

turning this switch ON/OFF.

EDM function

selector switch

Turn this switch ON when using the EDM output of the safety function. Turn OFF

the power cable before turning this switch ON/OFF.

USB connector

Use this mini-B USB connector to connect a PC. Even when the Inverter is being

operated by a PC, etc., via USB connection, it can still be operated using the

Digital Operator.

Connector for Digital

Operator

Use this connector to connect the Digital Operator.

Connector for optional

board

Use this connector to mount the optional board. (The optional board will be

released soon.)

Control circuit terminal

blocks A and B

These terminal blocks are used to connect various digital/analog input and

output signals for inverter control.

Multi-function contact

terminal block

Use this SPDT contact terminal block for relay outputs.

Main circuit terminal

block

Use this terminal block to connect an output to the motor and Bracking Resistor,

etc. Also, use this terminal block to connect the inverter to the main power

supply.

CHARGE indicator

(Charge indicator LED)

This LED indicator is lit if the DC voltage of the main circuit (between terminals

P/+2 and N/-) remains approx. 45 V or above after the power has been cut off.

Before wiring, etc. confirm that the Charge LED indicator is turned OFF.

03 Installation

03.1 Mounting of the 3G3MX2

The frequency inverter is intended for vertical wall mounting. The frequency inverter must be installed on a wall

surface made of non-flammable material (e.g. metal).

The following mounting distances to other components must be observed to ensure sufficient ventilation.

03 Installation

03.2 Installation/removal method of the terminal block cover

Disassemble the terminal block cover in the following steps:

1. Loosen the screw(s) securing the terminal block cover.

2. Press the terminal block cover in the direction of the arrow and lift it down to remove it.

03.3 Wiring of the 3G3MX2

Power connections

Initially, it must be determined whether the frequency inverter used requires a three-phase power supply only

with terminals [R/L1], [S/L2] and [T/L3] or a single-phase power supply only with terminals [L1] and [N]. The

corresponding connections can be seen in the figure below.

WARNING: Do not connect AC voltage to output terminals

It must be ensured that no AC voltage is connected to the output terminals. Otherwise, the

inverter may be damaged and there is a risk of injury and/or fire.

03 Installation

Logic control wiring

Before wiring the logic controller, a power-up test must be performed (see chapter 04 Commissioning).

Tabla de contenidos

Otros manuales de Inversor de Omron

Omron

Omron 3G3RX-A2004-V1 Manual de usuario

Omron

Omron SYSDRIVE 3G3EV-AB004-CE Manual de usuario

Omron

Omron KP100L-OD - 12-2010 Manual de usuario

Omron

Omron Varispeed E7 Manual de usuario

Omron

Omron 3G3MX2 Series Manual de usuario

Omron

Omron JX - 2 Manual de usuario

Omron

Omron SYSDRIVE 3G3EV SERIES Manual de usuario

Omron

Omron V7-IP65 Manual de usuario

Omron

Omron RX - 2 Manual de usuario

Omron

Omron SYSDRIVE 3G3FV Manual de usuario

Omron

Omron SYSDRIVE 3G3MV SERIES Guía rápida

Omron

Omron CIMR-L7Z - Manual de usuario

Omron

Omron SYSDRIVE MX2 SERIES Manual de usuario

Omron

Omron 3G3RX2-A2 Series Manual de usuario

Omron

Omron SYSDRIVE 3G3FV CE Series Manual de usuario

Omron

Omron 3G3RX-V1 Series Manual de instrucciones

Omron

Omron J1000 Guía rápida

Omron

Omron SYSDRIVE 3G3SV-B2002-E Manual de usuario

Omron

Omron RX - 2 Manual de usuario

Omron

Omron VARISPEED F7 Manual de usuario

Omron

Omron 3G3MX2 Series Manual de usuario

Omron

Omron SYSDRIVE 3G3RV Manual de usuario

Omron

Omron 3G3M1-STD Manual de usuario

Omron

Omron VARISPEED F7 Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario