Omnimount TVM PRO Series Manual de usuario

TVM PRO Television Wall Mount

Installation Instructions

Models: TVM 21 PRO

TVM 27 PRO

Parts List:

Item

Description Quantity

1 Wall Bracket 1

2 Support Arm 1

3 Platform 1

4 Platform Swivel Bracket 1

5 Nose Piece 1

6 Square Washer 1

7 Platform Slide Bar 1

8 Medium Hex Wrench 1

9 5/16” x 1” Platform Screw 1

10 Flat Washer 1

11 Small Hex Wrench 1

12 M6 x 20mm Tilt Screws 2

13 3/8” x ½” Pivot Bolts 2

14 5/16” Platform Lock Nut 1

15 Large Hex Wrench 1

16 Wall Bracket Cover 1

17 Wall Anchors 4

18 ¼” x 2” Lag Bolts 4

19 Security Strap 1

Step 1

Use electronic stud finder to locate center of stud.

Note: When mounting to masonry, go directly to Step 2

Step 2

Use wall bracket (1) as template to mark mounting hole locations.

Wooden Stud Mounting:

Using 1/8” drill bit, drill mounting holes to a depth of 2”.

Using a 10mm wrench, bolt the wall bracket to the wall with the supplied ¼” lag bolts (18).

Note: To make installation easier, dab a bit of liquid soap onto the bolt threads before driving bolt into the stud.

Masonry Mounting:

Use a 3/8” masonry drill bit, and drill mounting holes to a depth of 2”.

Insert wall anchors (17) into mounting holes, and tap flush with hammer.

Using a 10mm wrench, bolt the wall bracket to the wall with the supplied ¼” lag bolts (18).

Step 3

3a) Slide wall bracket cover (16) over support arm, with flat side facing wall.

Place flat washer (10) into round depression in center of platform swivel bracket (4).

Insert platform tilt screws (12) up through two countersunk holes in bottom of platform

swivel bracket.

3b) Insert 5/16” platform screw (9) down through center of platform swivel bracket. Place

platform swivel bracket assembly onto top plate at end of support arm, with main bolt

passing through center hole.

Install square washer (6) onto platform main bolt, and then thread platform lock nut (14)

onto platform screw. Tighten platform screw with medium hex wrench (8). Do not over-

tighten or platform will not swivel.

TVM PRO Television Wall Mount

3c) Place platform on top of platform swivel bracket, with platform tilt

screws passing through slots on platform as shown. Turn front edge of

platform at right angles to support arm, as shown. Insert small hex wrench

through holes in bottom of platform support, and thread platform tilt screws

into threaded ends of platform slide bar (7). using small hex wrench (11),

as shown.

Step 4

Insert support arm into wall bracket. Thread 3/8” pivot bolts

into support arm, and secure with large hex wrench.

Do not over tighten lock nut, or arm will not swing freely.

Snap wall bracket cover into place.

Note: If using the optional TVC component mount, install it at this time.

Step 5

Thread open end of security strap (19) up through a slot on the outer edge of platform, across the platform, and then

down through the other slot. Place TV squarely onto platform.

Pull two ends of security strap over TV, thread strap ends through strap buckle (as shown),

and secure tightly.

Optional: Bolt TV to the platform by passing security screws (not supplied) through grid on bottom of platform into

threaded lands on bottom of TV.

Note: You must consult the TV manufacturer for the correct size and length of bolts to use for your make/model of

television. Failure to do so may result in damage to the TV.

Step 6

Adjust platform for desired amount of tilt:

To increase tilt angle, hold top of TV and carefully push front edge of platform backwards.

To decrease tilt angle, hold top of TV and carefully pull front edge of platform forwards.

With tilt angle set, turn front edge of platform at right angles to support arm. Insert small hex wrench

through holes in bottom of platform support as shown, and tighten tilt screws securely.

Step 7

If desired, press nose piece (5) into place at end of support arm, as shown.

OmniMount Systems, Inc.

8201 S. 48

Street • Phoenix, AZ 85044

1-800-MOUNT-IT • www.omnimount.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Soporte de TV de Omnimount

Omnimount

Omnimount PLAY70 Manual de usuario

Omnimount

Omnimount CI125FM Manual de usuario

Omnimount

Omnimount UL10333 Manual de usuario

Omnimount

Omnimount WM1-L Manual de usuario

Omnimount

Omnimount LEDP75 Manual de usuario

Omnimount

Omnimount ELEMENTS 403 FP Manual de funcionamiento

Omnimount

Omnimount OM10017 Manual de usuario

Omnimount

Omnimount 63FBHD-T Manual de usuario

Omnimount

Omnimount CP24 Manual de usuario

Omnimount

Omnimount ELEMENTS 403 FP Manual de usuario

Omnimount

Omnimount PRO HD CART Manual de usuario

Omnimount

Omnimount OE80FM Manual de usuario

Omnimount

Omnimount WM4-S Manual de usuario

Omnimount

Omnimount LEDW60 Manual de usuario

Omnimount

Omnimount VB150T Manual de usuario

Omnimount

Omnimount ULPC-X Manual de usuario

Omnimount

Omnimount OL125 C Manual de usuario

Omnimount

Omnimount OE150T Manual de usuario

Omnimount

Omnimount 10034 Manual de usuario

Omnimount

Omnimount OC100F Manual de usuario

Omnimount

Omnimount SW1 Manual de usuario

Omnimount

Omnimount CI80FMX Manual de usuario

Omnimount

Omnimount PANA103PRO Guía

Omnimount

Omnimount OE150FM Manual de usuario

Manuales populares de Soporte de TV de otras marcas

Ergotron

Ergotron Neo Flex Cantilever UHD Manual de usuario

StarTech.com

StarTech.com FPCEILBTB Manual de usuario

VonHaus

VonHaus 05/038 Manual de usuario

Techlink

Techlink ECHO TV Manual de usuario

Sandstrom

Sandstrom SSTVMC12X Manual de usuario

Sony

Sony SU-WL700 Guía

ICW

ICW SCACC18 Manual de usuario

LG WM-L640V Manual de usuario

Gembird

Gembird WM-65ST-01 Manual de usuario

ERARD

ERARD FiTUP XXL 035320 Manual de usuario

PEERLESS

PEERLESS PLCK-1 Guía

Kanto

Kanto RCF180 Manual de usuario

GEM

GEM GEM GP001 Manual de usuario

Gladiator Joe

Gladiator Joe GJ0A0053 Manual de usuario

Vivotek

Vivotek AM-105 Manual de usuario

Vivo

Vivo VESA STAND-VAD1B Manual de usuario

AmazonBasics

AmazonBasics B07QG3LMG4 Manual de usuario

Secura

Secura QLF210 Manual de usuario