Omix-Ada EXO-Top Manual de usuario
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Page 1/30
13516.02
4-Door EXO-Top Roof Rack System
OMIX-ADA®TECHNICAL SUPPORT
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
The EXO-Top Roof Rack System is rated to a dynamic 300 lb, evenly distributed
load. Further loading could result in serious injury or death.
maintenance for further instructions.
WARNING
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Page 2/30
Table of Contents
Important Safety Information (3)
Components List (4)
Section A - Preparing for Installation; Removal of Factory Top (8)
Section B - Cage Assembly and Installation (11)
Section C - Surrounds Assembly and Installation (13)
Section D - Bow and Slider Assembly and Installation (14)
Section E - Soft Top Assembly and Installation (19)
Operating Procedure (24)
Care and Maintenance (30)
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Your Rugged Ridge® Exo-Top is intended to increase the utility and enjoyment of your
vehicle. Before installation, please take a moment to review the following safety information
and installation instructions. Important safety information is generally preceded by one of
three signal words indicating the relative risk of injury. The signal words mean:
A hazardous situation which, if not avoided, could result in death or serious
injury. You CAN be killed or seriously hurt if you don’t follow instructions.
A hazardous situation which, if not avoided, could result in minor or moderate
injury. You CAN be moderately hurt and also may suffer property damage if
you don’t follow instructions.
Careful attention is required to this instruction or operation but does not generally
relate to personal injury. Damage to your product or other property may result if you don’t
follow instructions.
We hope you enjoy your Rugged Ridge® purchase and are here to help if you still have
questions after reviewing this safety information and instructions. See Customer Service
contacts included with your Limited Warranty.
Page 3/30
Important Safety Information
WARNING
CAUTION
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Components List
9
10
11
12
13
14
12
3
4
5
8
6
7
Cage Assembly
1. Cage Base, LH (1)
2. Cage Base, RH (1)
3. Rear Cage Bar (1)
4. T Bar, Rear (1)
5. T Bar, Front (1)
6. Center Cross Bar (1)
7. Front Side Bar, LH (1)
8. Front Side Bar, RH (1)
Cage Hardware
9. M8x40 Button Head Bolt (24)
10. M10x25 Button Head Bolt (8)
11. M8 Nylon Hex Nut (24)
12. Nut Plate, Flat - M10 Hex Nut (6)
13. Nut Plate, Angled - M10 Hex Nut (2)
14. M10 Washer (8)
Page 4/30
Ensure all components and hardware are provided before beginning installation
process.
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Components List
1
2
3
4
5
6
7
8
9
Surrounds Assembly
1. Front Surround, LH (1)
2. Front Surround, RH (1)
3. Rear Lower Surround, LH (1)
4. Rear Lower Surround, RH (1)
5. Rear Upper Surround, LH (1)
6. Rear Upper Surround, RH (1)
7. Seal, LH (1)
8. Seal, RH (1)
Surrounds Hardware
9. M8x30 Knob (2)
Page 5/30
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Page 6/30
Components List
3
4
6
87
9
10 11
12 13 14 15
51
2
16
Slider System Assembly
1. Front Bow Assembly (1)
2. Rear Bow Assembly (1)
3. Slider Carriage Assembly, LH (1)
4. Slider Carriage Assembly, RH (1)
5. Rail (2)
Slider System Hardware
6. Front Surround Bracket, RH (1)
7. Front Surround Bracket, LH (1)
8. Mid-Rail Bracket, RH (1)
9. Mid-Rail Bracket, LH (1)
10. Rear Rail Bracket, RH (1)
11. Rear Rail Bracket, LH (1)
12. M8x18 Flathead Bolt (6)
13. M8 Nylon Lock Nut (6)
14. M8x70 Socket Cap Bolt (4)
15. M8x25 Socket Cap Bolt (2)
16. 5/16 x 1 1/4 Washer (6)
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
3
4
5
2
1
Soft Top Assembly
1. Soft Top Fabric (1)
2. Rear Window (1)
3. Side Window, LH (1)
4. Side Window, RH (1)
Soft Top Hardware
5. Release Clips (Carabiner) 1.5” ID (2)
Page 7/30
Components List
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Page 8/30
Section A - Preparing for Installation; Removal of Factory Top
1. Soft Top owners: Refer to owners’ manual for instructions
on lowering factory top. Once lowered, unscrew shoulder
bolts fastening it to vehicle’s roll bars. Remove canvas from
assembly.
Hard Top owners: Refer to owners’ manual for instruction on
removing factory hard top. Skip to STEP 4 once hard top is
removed.
Hardtop owners will need to purchase a factory header,
tailgate bar, and tailgate bar retainers (LH, RH).
These factory parts are required:
Header - 68003646AA
Tailgate Bar - 55395757AC
Tailgate Bar Retainer, RH - 55395760AB
Tailgate Bar Retainer, LH - 55395761AB
Note: After removing header and factory soft top, place
assembly on ground as shown on right.
Tools Needed:
Phillips head screw driver
Torx bit socket wrench (T30)
Carefully read and understand all instructions before proceeding. We recommend you save all
parts and hardware if you ever choose to re-install the factory top.
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
2. Remove front and rear door surrounds from each side of
vehicle.
3. Remove metal soft top mounting brackets attached to
roll bar in cargo area.
4. Remove screws from underside of header at each end
that attaches fabric tabs.
Do not discard screws, they are reused in later
steps.
Page 9/30
Section A - Preparing for Installation; Removal of Factory Top
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
6. Loosen all screws from top side of header. Do not
remove completely.
5. Flip header and fabric and remove screws from top of
header at each end. You will now be able to remove OE
soft top frame.
7. Release fabric from header. Keep header and all
hardware for soft top installation.
Page 10/30
Section A - Preparing for Installation; Removal of Factory Top
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Omix-Ada
Omix-Ada
Omix-Ada Rugged Ridge Alloy 13551.18 Manual de usuario
Omix-Ada
Omix-Ada RUGGED RIDGE CJ Manual de usuario
Omix-Ada
Omix-Ada Alloy RUGGED RIDGE 13782.35 Manual de usuario
Omix-Ada
Omix-Ada 11704.05 Manual de usuario
Omix-Ada
Omix-Ada Rugged Ridge Alloy 13216.03 Manual de usuario
Omix-Ada
Omix-Ada Rugged Ridge 12300.52 Manual de usuario
Omix-Ada
Omix-Ada Rugged Ridge 13551.41 Manual de usuario
Omix-Ada
Omix-Ada 13216.01 Manual de usuario
Omix-Ada
Omix-Ada 13551.23 Manual de usuario
Omix-Ada
Omix-Ada Alloy Rugged Ridge X-Clamp Manual de usuario
