OMEGAbilance FREESTYLE COMPACT Series Manual de usuario
VIEW AND DIMENSIONS
MODEL CS
Freestyle Compact user manual Rev.1 Page 2 of 92
MODEL CS / P wall unit
CS / PA MODEL
Freestyle Compact user manual Rev.1 Page 3 of 92
PLC MODEL
Freestyle Compact user manual Rev.1 Page 4 of 92
MODEL PL
Freestyle Compact user manual Rev.1 Page 5 of 92
INSTALLING THE SCALE
POWER SUPPLY
The installation of this scale must be done with great care and attention, in order to ensure
maximum operating safety of the equipment.
Therefore it is essential to strictly observe the following rules:
-Power the scale with a preferential line (220 V ± 10% - 50 HZ) that starts directly from the
meter or from the distribution panel, avoiding that it connects other equipment with high
absorption (refrigerator compressors, slicers, neon lamps, etc. ). The power supply line of
the instruments must be connected to a single electrical phase to avoid imbalances in the
interconnections of the scales.
-Install a socket with side earth contacts (SCHUCO) for each scale; the connection to the
earth line is essential to allow the anti-disturbance filter, with which the scale is
equipped, to work correctly and to intervene when necessary to eliminate them. It is also
advisable that auxiliary sockets useful for test instruments are available near the scales.
ATTENTION!AN ELECTRIC LINE WITHOUT AN EARTH WIRE COULD CAUSE IMPROPER
OPERATION OF THE SCALE OR DAMAGE TO ITS ELECTRONIC CIRCUITS. THEREFORE, WE
DISCLAIM ANY LIABILITY FOR ANY OPERATING DEFECTS OR FOR ACCIDENTS TO THE
OPERATORS RESULTING FROM THE NON-COMPLIANCE OF WHAT WE RECOMMEND.
Freestyle Compact user manual Rev.1 Page 6 of 92
LOCKING THE SCALE
The scale with weight detection by means of a magnetic repulsion transducer or strain
gauge load cell does not require any locking of the weight system.
SWITCHING ON THE SCALE AND AUTOMATIC ZEROING
The switching on of the scale must be carried out only with the plate unloaded, clean and without objects above it and
the scale will be placed with the weight system at “zero”.
After the brand logo, the scale will display the current date and time, kept updated by the
clock incorporated in the scale.
By pressing the key"ENTER "the MASTER, SUBMASTER or SLAVE (according to the scale
configuration), the bank number and the network number assigned to the scale will be displayed for
a few seconds. It is essential that the MASTER scale is switched on and enabled first, while the
switching on order of the other SUBMASTER or SLAVE scales can be random.
If the scale is inserted in a MULTIBANK system, the SLAVE scales must only be switched on after the
respective MASTER or SUBMASTER scale.
The following anomalous conditions may occur and are highlighted by specific reports:
- "ALREADY PRESENT ": indicates that the scale has the same address as another already active in the network
- "MASTER ABSENT ": indicates that a SLAVE scale has been turned on before its" MASTER "or"
SUBMASTER "
- "NO CONFIGURATION ": indicates that a" SUB MASTER "scale was turned on before the"
MASTER "
USE OF THE SCALE
PRICE SETTING
The price per kg can be set indifferently before or after placing the goods on the weighing
pan.
By setting the price with the numeric keyboard, the "Price € / Kg" box will be opened in the viewer. By
pressing the "ENTER”The price will be shown in the" PRICE € / Kg "display for the calculation of the
amount of the item placed on the scale plate.
It is possible to execute the transaction immediately if, after setting the price of the item, you
proceed directly to the identification of the operator.
The button "C.”Allows you to cancel any setting errors.
All the totals of the weighs whose prices have been entered directly with the alphanumeric keyboard
will be totalized as "ARTICLE 0" and "FAMILY 0".
It is possible to inhibit the use of article 0; in this case the operator can only use the prices stored
and associated with the PLUs (see chapter CONFIGURATION - Various Settings).
It is also possible that the set price appears directly on the display of the price per kilogram
(see chapter CONFIGURATION - Various Settings).
RECALL OF PRICES AND STORED TARE (PLU)
To recall a stored price (PLU) press the key"PLU ",use the numeric keypad to compose the
number of the product to be treated and press"ENTER "to confirm. In addition to the price and
the tare, a description and possibly an image will appear on the display according to what has
been programmed.
Freestyle Compact user manual Rev.1 Page 7 of 92
It is possible to execute the transaction immediately if, after setting the article number, you
proceed directly to the identification of the operator.
The scale is equipped with a keyboard designed to quickly recall up to a maximum of 200
stored products (depending on the type of keyboard present).
Normally the keys of this keyboard recall the product codes ranging from 1 to 200, but it is
possible to associate a different address to each of these keys: in this way it is possible to
program the keyboard to recall the data of the most used products regardless of their address
memory (see the paragraph "PLU KEYS" in KEY OPERATIONS).
The maneuver for entering prices and PLU data to be stored is described in the appropriate
chapter under KEY OPERATIONS.
SETTING OF PRICES FOR NON-WEIGHED PRODUCTS
The button "+"Allows you to compose price values for products that are not weighed, that is, sold by the piece.
By pressing the "+"The" Price € / Pcs "box will be opened in the viewer and pressing the"ENTER”The price will be
shown in the displays" PRICE € / Kg "and" AMOUNT € ".
For any multiplication, after setting the price, press the "X", enter the number of pieces and press"
ENTER”To confirm: the number of packages set will be displayed in the weight display, the unit price
in the" PRICE € / Kg "display, and the total amount of packages in the" AMOUNT "display.
It is possible to execute the transaction immediately if, after setting the price of the item, you
proceed directly to the identification of the operator.
The button "C.”Allows you to cancel any setting errors.
As described in the previous chapter, the prices of items that are not weighed, but stored and
associated with a PLU, can be recalled.
Even for non-weighed products it is possible to inhibit the scale from accepting prices set from the
keyboard, allowing the operator to use only the prices previously stored and associated with the
PLUs. (See in the appropriate paragraph "ARTICLE 0" in KEY OPERATIONS).
Freestyle Compact user manual Rev.1 Page 8 of 92
RETURNS or TRANSFERS
The button"-"allows you to compose negative numerical values relating to RETURNS or BANK
TRANSFERS. Again, by pressing the "-”The value that the operator is typing will appear in the appropriate"
Negative € / Pc "box. The scale, inhibited by the normal weighing function for the entire duration of the
operation, returns active only when the operator is identified to record the transaction or by selecting
another PLU or by pressing the key"C ".
It is possible to execute the transaction immediately if, after having set the negative value, you
proceed directly to the identification of the operator.
RETURNS or BANK TRANSFERS are not allowed that make the total determined up to that moment
negative.
MULTIPLICATION OF GOODS SOLD IN BODY OR RETURNS
If the number of products sold in bulk or returns is more than one, after setting the unit
price, or recalling a PLU as explained above, it will be possible to carry out a multiplication
operation.
By pressing the key"X ",by typing the number of pieces on the numeric keypad and confirming with the "
ENTER”The result of the operation will be automatically calculated and displayed together with the
number of items counted and the unit price.
The scale, inhibited by the normal weighing function for the entire duration of the operation, returns
active only when the operator is identified to record the transaction or by selecting another PLU or by
pressing the key"C ".
It is possible to execute the transaction immediately if, after setting the number of pieces, you
proceed directly to the identification of the operator.
DISCOUNTS
Different types of discounts are possible; the selection of the desired discount type must be made on the
MASTER scale, on the SUBMASTER or by an external processor.
DISCOUNT FOR FAMILIES
The "DISCOUNT FOR FAMILIES" is applied to every transaction that uses a PLU combined with a
product family with a discount programmed.
The discount will be highlighted by printing: for each transaction the discount percentage with the relative discount; on
the total amount of the receipt, the total amount, the total discount and the final amount.
The discount provided for each family is introduced in the programming of the product
families (see "FAMILIES" in KEY OPERATIONS).
TOTAL DISCOUNT
The "TOTAL DISCOUNT" is applied to each transaction but is printed only at the end of the
receipt as the sum of the discounts.
The introduction of the total discount percentage is carried out in the programming of
"BANK INFORMATION".
0
Freestyle Compact user manual Rev.1 Page 9 of 92
INDIVIDUAL DISCOUNT
The "INDIVIDUAL DISCOUNT" is applied to all stored items containing a discount
percentage.
The "threshold" value is also present in the data of each stored article; if the threshold is different from 0, the
discount is made every time the net weight is equal to or greater than the threshold.
In the case of full PLU, the "NxM" discount is managed by inserting N (eg I buy 3) in the threshold and M (eg I
pay 2) in the discount. The discount occurs whenever the multiplication in the transaction meets the
requirements stored in the PLU.
Several thresholds are allowed, each of which is associated with a discount.
The relative discount is printed on the receipt for each transaction; the total amount, the total
discounts and the final amount are shown on the total on the receipt.
ATTENTION: If the threshold is set without a discount, this is to be understood as the “minimum
print weight”.
PLU-FAM DISCOUNT.
This type of discount includes both the PLU and the family discount.
If both discounts are present in a transaction, the PLU discount has priority over the family
discount.
OPERATOR DISCOUNT
The operator discount is implemented manually with the "F1" and "F2" keys respectively
used for:
F1 = single transaction discount.Must be used after PLU selection. Pressing it
a message appears on the display indicating the selection of the discount percentage value, once the
desired discount has been selected, press the OPERATOR key.
F2 = discount on the total.It must be used to close the receipt and once pressed yes
set the discount percentage on the total, then pressing the operator key closes the receipt.
The use of one type of discount excludes the other possibility, that is, they cannot be used within the
same transaction both discounts.
When the operator discount is selected on the scale, they cannot be combined with the "F1" and keys
"F2" of the MACRO functions as they are used to activate and insert discounts.
Freestyle Compact user manual Rev.1 Page 10 of 92
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Escala de OMEGAbilance
