Omega DPF700 Manual de usuario

DPF700

Dual Relay Option Board

for the DPF700 Meter

www.omega.com

e-mail: [email protected]

User’s Guide

Shop on line at

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New

Approach Directi es. OMEGA will add the CE mark to e ery appropriate de ice upon certification.

The information contained in this document is belie ed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reser es the right to alter

specifications without notice.

WARNING: These products are not designed for use in, and should not be used for, patient-connected applications.

This de ice is marked with the international caution symbol. It is important to read the Setup Guide before installing or commissioning this de ice as the guide contains important

information relating to safety and EMC.

This de ice is marked with the international caution symbol. It is important to read the Setup Guide before installing or commissioning this de ice as the guide contains

important information relating to safety and EMC.

Servicing North America:

USA: One Omega Dri e, P.O. Box 4047

ISO 9001 Certified Stamford CT 06907-0047

TEL: (203) 359-1660 FAX: (203) 359-7700

e-mail: [email protected]

Canada: 976 Bergar

La al (Quebec) H7L 5A1

TEL: (514) 856-6928 FAX: (514) 856-6886

e-mail: [email protected]

For immediate technical or application assistance:

USA and Canada: Sales Ser ice: 1-800-826-6342 / 1-800-TC-OMEGA®

Customer Ser ice: 1-800-622-2378 / 1-800-622-BEST®

Engineering Ser ice: 1-800-872-9436 / 1-800-USA-WHEN®

Mexico and TEL: (001)800-TC-OMEGA® FAX: (001) 203-359-7807

Latin America: En Español: (001) 203-359-7803

e-mail: [email protected]

Servicing Europe:

Benelux: Postbus 8034, 1180 LA Amstel een, The Netherlands

TEL: +31 20 3472121 FAX: +31 20 6434643

Toll Free in Benelux: 0800 0993344

e-mail: [email protected]

Czech Republic: Frystatska 184, 733 01 Kar iná

TEL: +420 59 6311899 FAX: +420 59 6311114

e-mail: [email protected]

France: 11, rue Jacques Cartier, 78280 Guyancourt

TEL: +33 1 61 37 29 00 FAX: +33 1 30 57 54 27

Toll Free in France: 0800 466 342

e-mail: [email protected]

German /Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

TEL: +49 7056 9398-0 FAX: +49 7056 9398-29

Toll Free in Germany: 0800 639 7678

e-mail: [email protected]

United Kingdom: One Omega Dri e

ISO 9002 Certified Ri er Bend Technology Centre

Northbank, Irlam Manchester M44 5BD United Kingdom

TEL: +44 161 777 6611 FAX: +44 161 777 6622

Toll Free in England: 0800 488 488

e-mail: [email protected]

OMEGAnet® On-Line Service

www.omega.com

Internet e-mail

[email protected]

PREFA E

MANUAL OBJE TIVES

This manual shows you how to install and use the Dual-Relay option board with the DPF700

meter.

In this manual we pro ide procedures for:

* Setting up the Dual-Relay option board

* Installing the Dual-Relay option board

Use this manual with you DPF700 manual (M1676)

NOTES and AUTIONS

Information that is especially important to note is identified by these labels:

• NOTE

• WARNING

• AUTION

• IMPORTANT

NOTE: pro ides you with information that is important to successfully setup

and use the Programmable Digital Meter.

AUTION or WARNING: tells you about the risk of electric shock.

AUTION, WARNING or IMPORTANT: tells you of circumstances or

practices that can effect the meter's functionality and must refer to

accompanying documents

Note ☞

TABLE OF ONTENTS

1.1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.2 SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2.1 INSTALLING THE DUAL-RELAY OPTION BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2.2 SETTING UP THE DUAL-RELAY OPTION BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2.3 ELECTRICAL CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

3.1 RELAY OUTPUT OPTION BOARD SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . .6

FIGURES

2.1 DUAL RELAY OPTION BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2.2 SETPOINT EXAMPLE ILLUSTRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.3 ELECTRICAL WIRING FOR RELAY CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.4 DUAL RELAY CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

TABLES

2.1 SETPOINT EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

1.1 UNPA KING

Remo e the Packing List and erify that all equipment has been recei ed. If there are any

questions about the shipment, use the phone number for the Customer Ser ice Department

nearest you.

Upon receipt of shipment, inspect the container and equipment for any signs of damage. Take

particular note of any e idence of rough handling in transit. Immediately report any damage to

the shipping agent.

The carrier will not honor any claims unless all shipping material is saved for their

examination. After examining and removing contents, save packing material and carton

in the event reshipment is necessary.

1.2 SAFETY ONSIDERATIONS

Refer to your main owners guide manual for complete safety considerations.

This option card is intended for use in a DPF700 panel mount de ice that is protected in

accordance with Class I of EN 61010 (115/230 AC power connections). Installation of this

instrument should be done by Qualified personnel.

• Do not exceed oltage rating on the label located on the top of the instrument housing.

• Always disconnect power before changing signal and power connections.

• Do not use this instrument on a work bench without its case for safety reasons.

• Do not operate this instrument in flammable or explosi e atmospheres.

• Do not expose this instrument to rain or moisture.

• Unit mounting should allow for adequate entilation to ensure instrument does not

exceed operating temperature rating.

• Use electrical wires with adequate size to handle mechanical strain and power

requirements. Install without exposing bare wire outside the connector to minimize

electrical shock hazards.

Note ☞

2.1 INSTALLING THE DUAL-RELAY OPTION BOARD

To install the dual-relay option board, follow these steps (refer to the Figure 2-1):

!AUTION: The meter has no power-on switch, so it will be in operation

as soon as you apply power.

!IMPORTANT: Disconnect the power from the unit before installing this

option board.

1. Hold the board in a horizontal position, with the TB3 connector facing towards the

rear of the meter.

2. Line up the 3 connectors located on the back side of the board with pin groups J3, J4

and J5 on the mother card.

3. Push connectors down to secure on relay board.

Figure 2-1. Dual-Relay Option Board

NC1 N01 CM1 NC2 NO2 CM2

123456

TB3/RELAY

RELAY BD MAIN BD

123

TB1

123456

TB2

OPEN

CLOSED

12345678910

TB3

2.2 SETTING UP THE DUAL-RELAY OPTION BOARD

You may enter a setpoint from -99999 to 999999 with a decimal point in any of the following

positions: 9.9.9.9.9.9. After applying the scale factor and offset, the displayed measurement is

compared to the setpoint alues.

LO ALARM

Displayed alue is less than Setpoint LO

HI ALARM

Displayed alue is more than Setpoint HI

HYSTERESIS

Relay 2 is energized when display alue is more than Setpoint HI. Relay 2 is not

energized when display alue is less than Setpoint LO

Setpoint Example:

Setpoint H is 500.0 and Setpoint LO is 100.0.

Reading changes from 0 to 600 and back to 0.

Figure 10-2 on the following page illustrates Table 2-1.

Table 2-1. Setpoint Example

Alarm Status

Reading LO (Relay 1) HI (Relay 2) HYS

0 On Off Off

99.9 Off Off Off

300 Off Off Off

500.0 Off Off Off

500.1 Off On On

600 Off On On

500.1 Off Off On

100 - 500 Off Off On

99.9 On Off Off

0 On Off Off

2.2 SETTING UP THE DUAL-RELAY BOARD ( ontinued)

Figure 2-2. Setpoint Example Illustration

To con ert Setpoint LO to a second high setpoint, set software switch 3 of the configuration

menu to 1 (ConFIG = XX1XXX). LO ALARM becomes acti e when the reading is greater (more

positi e) than that setpoint.

To con ert both setpoints to latched setpoints, set software switch 2 of the configuration menu to

1 (ConFIG =X1XXXX). When relays are energized, they stay energized until a Reset (either

front-panel or back connector reset).

STANDARD RELAY OPTION

RELAY OPERATION WITH HYSTERESIS

RELAY 1 (LO)

RELAY 2 (HI)

RELAY 1 (LO)

RELAY 2 (HI)

RELAY 1 (LO)

RELAY 2 (HI)

RELAY 1 (LO)

(RELAY ON OR ENERGIZED)

(RELAY ENERGIZED)

99.9

SET POINT 99.90

OFF

OFF OFF

OFF

OFF OFF

500.1

2.3 ELE TRI AL ONNE TION AND SPE IFI ATION

Each relay has a form C contact. Refer to Figure 2-1 and Figure 2-3 to locate contacts and S5

switch.

* Install S5-A to control Relay 2 with hysteresis action.

* Install S5-B to control Relay 2 with setpoint HI.

* TB3-1 is a normally closed contact of relay 1.

* TB3-2 is a normally open contact of relay 1.

* TB3-3 is a common contact of relay 1.

* TB3-4 is a normally closed contact of relay 2.

* TB3-5 is a normally open contact of relay 2.

* TB3-6 is a common contact of relay 2.

Figure 2-3. Electrical Wiring for Relay onnections

Figure 2-4. Dual-Relay onnections

10-1. Dual-Relay Option Board

TB1

123

123456

TB2

TB3

EXTERNAL

LOAD

FUSE

RELAY 1 RELAY 2

NC1

NO1

CM1

NC2

NO2

CM2

TB3—1

TB3—2

TB3—3

NC1

NO1

CM1

TB3—4

TB3—5

TB3—6

NC2

NO2

CM2

RELAY1

RELAY2

K2 A

BS5

SETPOINT LOW OUTPUT

HYSTERESIS OUTPUT

SETPOINT HIGH OUTPUT

3.1 RELAY OUTPUT OPTION BOARD SPE IFI ATIONS

2 Form "C" on/off relays.

Configurable for latched and unlatched by software.

Max Current: 5 Amps, resisti e load.

Max Voltage: 250 Vac or 28 Vdction D

NOTES

aults

Otros manuales para DPF700

Tabla de contenidos

Otros manuales de Instrumento de medición de Omega

Omega

Omega DP25B-E Manual de usuario

Omega

Omega HHF1001A Manual de usuario

Omega

Omega RH62F Manual de usuario

Omega

Omega HHM598F Manual de usuario

Omega

Omega RD-MV100 Series Manual de usuario

Omega

Omega FPD-4000 Series Manual de usuario

Omega

Omega i-SERIES Manual de usuario

Omega

Omega DP26-RTD Manual de instrucciones

Omega

Omega HHG1394 Manual de usuario

Omega

Omega PHH-1X Litmustik Manual de usuario

Omega

Omega FMA 4000 Manual de usuario

Omega

Omega HHF143 Manual de usuario

Omega

Omega APH2 Manual de usuario

Omega

Omega HHF1001A Manual de usuario

Omega

Omega FLR 1000 Manual de usuario

Omega

Omega DP25B-S Manual de usuario

Omega

Omega DMD4008 Manual de usuario

Omega

Omega HHP400 Manual de usuario

Omega

Omega Vortex FV100 Series Manual de usuario

Omega

Omega DPG1001AD Manual de usuario

Omega

Omega LVCN400 Series Manual de usuario

Omega

Omega DP41-B Series Manual de usuario

Omega

Omega iServer 2 Series Manual de usuario

Omega

Omega FL-2000 Series Instrucciones de instalación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario