Olympus HST-Lite Manual de usuario
DMTA-20045-01EN — Revision A
October 2012
HST-Lite Scanner
User’s Manual
Olympus NDT, 48 Woerd Avenue, Waltham, MA 02453, USA
© 2012 Olympus NDT, Inc. All rights reserved. No part of this publication may be
reproduced, translated, or distributed without the express written permission of
Olympus NDT, Inc.
This document was prepared with particular attention to usage to ensure the
accuracy of the information contained therein, and corresponds to the version of
the product manufactured prior to the date appearing on the title page. There
could, however, be some differences between the manual and the product if the
product was modified thereafter.
The information contained in this document is subject to change without notice.
Part number: DMTA-20045-01EN
Revision A
October 2012
Printed in Canada
All brands are trademarks or registered trademarks of their respective owners and
third party entities.
DMTA-20045-01EN, Rev. A, October 2012
Table of Contents iii
Table of Contents
Labels and Symbols ........................................................................................... 1
Important Information — Please Read Before Use ..................................... 3
Intended Use .......................................................................................................................... 3
Instruction Manual ................................................................................................................ 3
Instrument Compatibility ..................................................................................................... 4
Safety Symbols ....................................................................................................................... 4
Safety Signal Words ............................................................................................................... 5
Note Signal Words ................................................................................................................. 6
Warnings ................................................................................................................................. 6
WEEE Directive ...................................................................................................................... 7
Warranty Information ........................................................................................................... 7
Technical Support .................................................................................................................. 8
1. HST-Lite Scanner ......................................................................................... 9
1.1 Positioning the Frame Bar ....................................................................................... 10
1.2 Installing a Probe and a Wedge in a Probe Holder .............................................. 11
1.3 Setting the Distance Between Beam Exit Points ................................................... 13
1.4 Positioning the Wheel Encoder ............................................................................... 16
1.5 Installing Tubing and Cables .................................................................................. 16
1.6 Installing the Cable Sheath ...................................................................................... 19
1.7 Scanner Wheels ......................................................................................................... 22
1.8 Installing a Preamplifier .......................................................................................... 24
1.9 Offset Probe Configuration ..................................................................................... 26
2. Parts and Accessories ................................................................................ 29
2.1 Standard Accessories ................................................................................................ 29
2.2 Optional Accessories ................................................................................................ 30
DMTA-20045-01EN, Rev. A, October 2012
iv Table of Contents
3. Specifications .............................................................................................. 31
List of Figures ................................................................................................... 33
List of Tables ..................................................................................................... 35
Index ................................................................................................................... 37
DMTA-20045-01EN, Rev. A, October 2012
2 Labels and Symbols
Table 1 Content of the marking
Marking:
Contains:
S/N The serial number.
The CE marking is a declaration that this product conforms to
all the applicable directives of the European Community. See
the Declaration of Conformity for details.
The WEEE symbol indicates that the product must not be
disposed of as unsorted municipal waste, but should be
collected separately.
DMTA-20045-01EN, Rev. A, October 2012
Important Information — Please Read Before Use 3
Important Information — Please Read Before Use
Intended Use
The HST-Lite Scanner is designed to perform nondestructive inspections on industrial
and commercial materials.
Do not use the HST-Lite Scanner for any purpose other than its intended use. It must
never be used to inspect or examine human or animal body parts.
Instruction Manual
This instruction manual contains essential information on how to use this Olympus
product safely and effectively. Before using this product, thoroughly review this
instruction manual, and use the product as instructed.
Keep this instruction manual in a safe, accessible location.
DMTA-20045-01EN, Rev. A, October 2012
4 Important Information — Please Read Before Use
Instrument Compatibility
The HST-Lite Scanner is compatible with the ancillary Olympus equipment listed in
Table 2 on page 4. For a list of other compatible parts and accessories, refer to chapter
2 on page 29.
Using incompatible equipment could cause malfunction and/or equipment damage.
Safety Symbols
The following safety symbols might appear on the instrument and in the instruction
manual:
General warning symbol:
This symbol is used to alert the user to potential hazards. All safety messages that
follow this symbol shall be obeyed to avoid possible harm.
Table 2 Ancillary equipment
Equipment Description
OmniScan MX Phased array instrument
TomoScan FOCUS LT Phased array instrument (using the optional
C1-DE15F-BXM-0.30M [U8767107] encoder adaptor)
OmniScan MXU OmniScan software
OmniScan MX2 Phased array instrument (using the adaptor
OMNI-A2-ADP20 [U8775201] supplied with the
instrument)
TOFD wedges ST1 and ST2 type
DMTA-20045-01EN, Rev. A, October 2012
Important Information — Please Read Before Use 5
High voltage warning symbol:
This symbol is used to alert the user to potential electric shock hazards greater
than 1000 volts. All safety messages that follow this symbol shall be obeyed to
avoid possible harm.
Safety Signal Words
The following safety symbols might appear in the documentation of the instrument:
The DANGER signal word indicates an imminently hazardous situation. It calls
attention to a procedure, practice, or the like, which, if not correctly performed or
adhered to, could result in death or serious personal injury. Do not proceed beyond a
DANGER signal word until the indicated conditions are fully understood and met.
The WARNING signal word indicates a potentially hazardous situation. It calls
attention to a procedure, practice, or the like, which, if not correctly performed or
adhered to, could result in death or serious personal injury. Do not proceed beyond a
WARNING signal word until the indicated conditions are fully understood and met.
The CAUTION signal word indicates a potentially hazardous situation. It calls
attention to an operating procedure, practice, or the like, which, if not correctly
performed or adhered to, could result in minor or moderate personal injury, material
damage, particularly to the product, destruction of part or all of the product, or loss of
data. Do not proceed beyond a CAUTION signal word until the indicated conditions are
fully understood and met.
DMTA-20045-01EN, Rev. A, October 2012
6 Important Information — Please Read Before Use
Note Signal Words
The following safety symbols could appear in the documentation of the instrument:
The IMPORTANT signal word calls attention to a note that provides important
information, or information essential to the completion of a task.
The NOTE signal word calls attention to an operating procedure, practice, or the like,
which requires special attention. A note also denotes related parenthetical
information that is useful, but not imperative.
The TIP signal word calls attention to a type of note that helps you apply the
techniques and procedures described in the manual to your specific needs, or
provides hints on how to effectively use the capabilities of the product.
Warnings
General Warnings
• Carefully read the instructions contained in this instruction manual prior to using
the instrument.
• Keep this instruction manual in a safe place for further reference.
• Follow the installation and operation procedures.
• It is imperative to respect the safety warnings on the instrument and in this
instruction manual.
• If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment could be impaired.
• Do not install substitute parts or perform any unauthorized modification to the
instrument.
Tabla de contenidos
Otros manuales de Escáner de Olympus
Olympus
Olympus ChainSCANNER Manual de usuario
Olympus
Olympus COBRA Manual de usuario
Olympus
Olympus FlexoFORM Manual de usuario
Olympus
Olympus SteerROVER Manual de usuario
Olympus
Olympus HST-X04 Manual de usuario
Olympus
Olympus HST-X04 Manual de usuario
Olympus
Olympus GLIDER Manual de usuario
Olympus
Olympus HSMT-Compact Manual de usuario
Olympus
Olympus HSMT-Flex Manual de usuario
