Olympia electronics GRL-37/90/WL Manual de usuario

Page 1 from 5923037016_09_001

SELF-TESTING NON MAINTAINED EMERGENCY LUMINAIRE WITH WIRELESS COMMUNICATION

TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 5)

220-240V AC/50-60Hz

90 min.

<24 h

POWER-CHARGE indicator, LAMP FAULT–BATT. FAULT indicator, TEST button

From overcharge and deep discharge

IP42

2x12V/7Ah

White Power LEDs

13.3W/14VA

5 to 40 C

Up to 95%

Aluminum, ABS/PC, PC

3 years (1 year for the battery)

3200lm

302 x 94 x 350 mm.

6310gr.

Thank you for your trust in our products

Olympia Electronics - European manufacturer

GRL-37/180/WL

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Pb)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

12V/7Ah

180 min.

4120gr.

GRL-37/90/WL

These luminaires are used (ta 40 C) where

emergency light is needed. Each luminaire must

be connected permanently to the mains power

supply.

OPERATION DESCRIPTION

GENERAL

When the unit is connected to the mains power

supply (after connecting the battery) the indicator

LAMP FAULT – BATT. FAULT remains OFF

whereas the indicator POWER CHARGE blinks to

indicate that the batteries are charging. When the

batteries are fully charged this indicator will light

permanently. If this indicator does not light then

probably the battery has not been connected. If

the batteries are connected and the indicator does

not light then contact a qualified service technician

for assistance. The charging procedure is

monitored by a microprocessor and is based on a

3 stage cycle thus ensuring a fast and full charge

of the battery. The charge current is supplied by a

high efficiency switch mode power supply which

ensures perfect charging even during the

fluctuations of the mains power supply.

BATTERY CUTOFF

The unit enters this state during the power supply

failure and when the battery has been fully

discharged. In this state the luminaire draws the

least power from the battery in order to prevent

deep discharge.

Is accomplished by briefly (<1 sec.) pressing the

TEST button. This permits the user to test the good

operation of the luminaire’s emergency circuit. The

unit simulates a power failure and the lamps are lit

using the batteries. This manual test does not affect

the automatic test.

When the luminaire is in emergency mode, with

corresponding pressings of the button, we can

choose the illumination of 100%, 50%, 33% or

turned off, either to increase the autonomy time or

not to consume the battery power unnecessarily.

This option is canceled when the network is

restored.

MANUAL TESTING

DIMMING OPTION

TX POWER

TX/RX FREQUENCY RANGE

11dBm

868.150-868.450MHz

EN 60598-1, EN 60598-2-22, EN 55015, EN 61547, EN 61000-3-2,

EN 61000-3-3, EN 62311, ETSI EN 303 446-1 V1.1.0, ETSI EN 300 220-2 V3.1.1

Page 2 from 5923037016_09_001

LAMP TESTING

AUTOMATIC DURATION TEST

Erasing errors is accomplished with a prolonged

pressing of the TEST button (>5 sec) when the unit

is connected to the mains power supply. The fault

indicated with the indicator LAMP FAULT / BATT.

FAULT will be erased. If the cause of the fault has

not been restored (i.e burned lamp) then the

indicator will light again. If the fault was caused by

a low emergency duration and you erase the error

then this will be indicated again during the next

duration test after 6 months. In this case (for

duration errors) it is vital to replace the battery

before erasing the error (the error is automatically

erased if the mains power and the battery are

disconnected).

AUTOMATIC EMERGENCY CIRCUIT TEST

The unit automatically tests the emergency circuit

every 15 days (if the battery and mains power are

connected) . During this test the lamps are turned

ON for 3 seconds using the batteries. In some

cases this function might not be acceptable (i.e in

cinema theaters) so the installer must take this

into account during the installation.

This test is conducted every 6 months by

simulating a power failure, if the battery and mains

power supply are connected. The unit lights the

lamps using the charged battery and counts the

time until the stated duration. If the lamps are ON

during the end of the test then the unit is restored

to its normal operation (lamps OFF and battery

charging). If the lamps go OFF before the end of

the test then the unit is restored to its normal

operation but the LAMP FAULT / BATT. FAULT

indicator is lit to show that there is a problem with

the battery and that the battery must be replaced.

Let it be noted that this duration test is also done

during every long power failure. If the power

failure lasts for a long time and the luminaire has

entered the BATTERY CUTOFF mode and the

duration measured is not correct then the fault

indicator will light when the power is restored.

ERASING ERRORS

The luminaire tests the good condition of the

lamps in emergency mode and warns the user for

probable malfunction. If a lamp is found faulty then

the LAMP FAULT indicator starts to blink. To verify

which lamp is faulty use the TEST button. If the

faulty lamp is replaced then the error is

automatically restored and the indicator is turned

OFF.

The WL luminaire models have the ability to

communicate over the air with Olympia’s control

panels for wireless emergency luminaires. The

luminaires can also communicate with a

PC/laptop through a gateway (Ethernet, Wi-Fi,

USB). For more information, please refer to

Wireless Emergency Lighting guides, available

on the company’s website.

procedure must be done only by qualified

Wireless communication

WARNING !!!

1. Every test, installation or maintenance

personnel.

3. The replacement of the battery and the

light source must be done using parts of

2. The unit must be connected to the mains

accordingly.

the same type, by the manufacturer or by

a competent person.

4. If the luminaire must be isolated from the

mains power supply for more than 2

months then the batteries must be

disconnected by removing the battery

power supply using a line fuse rated

connectors.

5. I s not allowed to discard batteries in to t i

common trash bins, they must be

discarded only in battery recycling

points. Do not incinerate.

Battery replacement

It can be done only by a competent person

and after the mains interruption.

1. Follow the step 2 of the installation

procedure.

2. Disconnect the cables and remove the

old battery.

3. Connect the new battery with the same

type (step 3 of the installation procedure)

and place it in the position of the old one.

4. Follow the step 6 of the installation

procedure and power the device.

2. Long press (>2"): Loads factory default

settings to the module.

Button functionality:

The on-board button has the two following

functions:

1. Short press (<2"): a status message will

be sent to the Gateway device of the

wireless network.

Button

LD3

LD2

LD1

Antenna

• SID: 00000001

Default settings:

• RF Channel: 13 ( 869.525MHz )

1. Very fast flash [5 times/s]: received signal

strength is excellent.

3. Moderate flash [1 second ON / 1 second

OFF]: received signal strength is acceptable

for reliable communication.

3. Fast flash [2 times/s]: The device has

5. No light: The device is disconnected.

1. Very fast blink [5 times/s]: the module is

not initialized correctly. In this case you

have to press for more than 2 seconds the

push button, in order to reset the module

(loads default settings).

established connection to a Router device

and at least one more Router device is

available on the same hop level, as an

alternate route (redundant connection).

The bottom LED (LD1-red) indicates

operation status.

(false condition).

This LED may blink according to the

following patterns:

The middle LED (LD2-green) indicates the

received signal strength (RSSI) of the router

module.

2. Rapid flash [5 times/s]: The device has

established direct connection to a single

Gateway device.

1. Steady ON: The device has established

direct connection to a Gateway device, and

at least one more Gateway device is

available for alternate routing

Wireless Communication LED

indications (interior)

The top LED (LD3-green) indicates the

network connection status.

This LED may blink according to the

following patterns:

4. Moderate flash [1 second ON / 1 second

OFF]: The device has established

connection to a single Router device, and

no alternatives exist on the same hop level.

This LED may blink according to the

following patterns:

2. Fast flash [2 times/s]: received signal

strength is good.

4. Very slow [2 seconds ON / 2 seconds

OFF]: received signal strength is not

acceptable for reliable communication, or

no signal.

2. Moderate flash [2 times/s]: The module

is properly operating.

Page 3 from 5 923037016_09_001

Page 4 from 5923037016_09_001

neutral (Fig. 2).

and red cable to (+) pole (Fig. 2).

4. Install the included cable gland or the rubber o-ring. Pass through the mains cable and stabilize it

1. Install the included mounting accessories to hook the device from the mounting holes (Fig.1).

2. Unfasten the 4 mounting screws to remove the front plastic cover (Fig.1).

3. Make sure that the battery’s cables are connected to the respective poles. Black cable to (-) pole

by fastening the cable gland. Connect the wires to the terminal blocks L for live wire and Ν for

1N*m).

5. Refit with care the front plastic cover, by fastening the 4 mounting screws (tightening torque

After the installation has finished, charge the batteries for at least 24 hours so as to obtain the

rated autonomy duration.

WARNING!!

INSTALLATION PROCEDURE (For wall mounting only)

INDICATION LED STATUS (with the mains power supply connected)

Indicator ON Indicator Blinking

Indicator OFF

POWER / CHARGE LAMP FAULT / BATT. FAULT

Disconnected battery / not charging Normal operation mode

Charged battery Low emergency duration (replace battery)

Battery under charge Lamp fault (Check lamps and replace if needed)

TEST

button

Fig. 1

POWER

CHARGE

indicator

Mounting holes

LAMP FAULT

BATT. FAULT

indicator

Cover

retaining

screws

Fig.2

Page 5 from 5923037016_09_001

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of

warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,

which accompanies each product. This warranty ceases to exist if the buyer does not follow the

technical instructions included in official documents given by Olympia Electronics or if the buyer

modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia

Electronics has fully agreed to them in writing. Products that have been damaged can be returned to

the premises of our company for repair or replacement, as long as the warranty period is valid.

www.olympia-electronics.com

72nd km. O.N.R. Thessaloniki-Katerini

WARRANTY

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

HEAD OFFICE

[email protected]

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge

the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or

not the buyer the transportation cost.

NOTE! The light source is non-user replaceable.

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

LED MODULE CHARACTERISTICS

Olympia Electronics S.A.

68 °C max. across the board

Cable connection between main pcb and led module

17.5-20.5V

14W

1005183

Manufacturer

Voltage Range

Connections

Nominal Power

Temperature (tc)

GRL-37/90/WL GRL-37/180/WL

180: 3 hour duration

90: 1.5 hour duration

C: Including inhibiting mode

LABELING EXPLANATION:

B: Including remote test mode

X: Self contained

A: Including test device

F: Automatic test gear complying with IEC 61347-2-7 denoted EL-T

0: Non maintained (*)

(*) Non Maintained operation: The luminaire turns on illumination source, only in case of power

supply failure.

NOTE: LED= Light Emitting Diode

A B C F

X90

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de olympia electronics

olympia electronics

olympia electronics GR-315/15L Manual de usuario

olympia electronics

olympia electronics GR-415/4P Manual de usuario

olympia electronics

olympia electronics GR-60 Manual de usuario

olympia electronics

olympia electronics ZLD-28/EM/ADR Manual de usuario

olympia electronics

olympia electronics KLD-30 Manual de usuario

olympia electronics

olympia electronics POWER LIGHT Series Manual de usuario

olympia electronics

olympia electronics GR-900/30L/SC Manual de usuario

olympia electronics

olympia electronics GR-938/15L/ADR Manual de usuario

olympia electronics

olympia electronics GR-940/15L Manual de usuario

olympia electronics

olympia electronics GRL-29/WL Manual de usuario

olympia electronics

olympia electronics GRL-22 Manual de usuario

olympia electronics

olympia electronics GR-60 Manual de usuario

olympia electronics

olympia electronics KLD-30/ST/ADR Manual de usuario

olympia electronics

olympia electronics KLD-30/CBS/24V/ADR Manual de usuario

olympia electronics

olympia electronics SLD-28/SP Manual de usuario

olympia electronics

olympia electronics TUV COMFORT LIGHT Series Manual de usuario

olympia electronics

olympia electronics GR-1938/4P Manual de usuario

olympia electronics

olympia electronics PLD-25/NiMH Manual de usuario

olympia electronics

olympia electronics GR-460 Manual de usuario

olympia electronics

olympia electronics GR-940/15L Manual de usuario

olympia electronics

olympia electronics GR-316/15L/MAR Manual de usuario

olympia electronics

olympia electronics GR-938/30L Manual de usuario

olympia electronics

olympia electronics GRL-37/90 Manual de usuario

olympia electronics

olympia electronics GR-292/M/HL/ADR Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

olympia electronics GRL-37/90/WL Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas