Olympia electronics GR-577/L/15/ST/WP Manual de usuario

Page 1 from 5923577007_09_001

GENERAL

These luminaires are used in places where

emergency luminaires are needed.

E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y

connected to mains power supply. In normal

operation (L1 connected to L) the led strip

lights and the battery is charging. In case of

a mains power supply failure the luminaire will

light the led strip automatically in emergency

mode (powered by its battery). When the

mains power supply is restored the device

turns to normal operation.

OPERATION

Battery Charging

The battery charging is completely controlled.

In this case, the best possible battery

maintenance is achieved, as well as the

elongation of its duration. When the battery

has completely charged, it charges with a

maintenance current.

Battery Cut-off

The luminaire enters in this operation when

the mains power supply fails and battery has

lost its energy. During this operation the

luminaire enters the idle state and battery

consumption is negligible, in order to be

protected from deep discharge.

Manual Test

This test can be done by placing the test card

on the side of the indications (page 4) and

remove it instantly an operation test is initiated.

The light source and the emergency circuit of

the device is monitored. The manual test can

be conducted only if the mains power supply

and the battery is connected. During this test

period all indication LEDs are OFF.

Automatic Operational Test

This test includes all the operations that provide

the manual test and is conducted automatically

every 15 days. In order to be performed, the

mains power supply and the battery should be

connected.

Automatic Autonomous Test

The Automatic Autonomous Test is conducted

and measures the device’s back up operation

and emergency duration. This test is conducted

automatically every 6 months. In order to be

performed, the mains power supply and the

battery should be connected and fully charged.

If the battery is not fully charged, the test is

postponed until the battery is completely

charged. If during this test, the autonomy is less

than nominal then the battery fault led turned

on continuously and the battery must be

replaced.

220-240V AC/50-60Hz

90 min

7630gr7480gr (double side)

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

LIGHT SOURCE INTENSITY (230V AC/emerg.)

ILLUMINATION SOURCE

24 h

Charge LED, Lamp Fault, Battery Fault

From overcharge and deep discharge

White LEDs

5 to 40 C

Up to 95%

3 years (1 year for the battery)

Painted steel plate (RAL 7036), ABS/PC, PC

IP 66

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

480 x 480 x 105 mm

4.8V/1.5Ah

9W / 9.5VA - PF: 0.95/230V

680lm / 340lm

WATERPROOF SELF TESTING MAINTAINED

EMERGENCY LUMINAIRE SIGNS (for tunnels ) WITH LEDs

GR-577/L/15/ST/WP GR-577/L/15/ST/WP/O

TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see p a ge 5)

Thank you for your trust in our products.

Olympia Electronics - European manufacturer.

Page 2 from 5

Back Up Operation

The autonomous duration of battery during

emergency mode is at least the one that is

stated in the list of the technical

characteristics. During emergency mode, a

light source test is also performed.

Resetting Errors

Place the test card A-1900 on the side of the

indications (page 4) and remove it after the

reset is conducted (the indications light in

sequence), to delete all the indicated LED

errors. Then the luminaire enters regular

operation mode.

Indication LED status (with connected

mains power supply).

Charge

On: Good charge current.

Οff: No battery (No charging current

or disconnected battery).

Lamp Fault (with L1 connected to L)

Οn (with LED strip off): Faulty LED strip

(must be replaced).

Οn (with LED strip on): Problem in the back

up circuit of the LED strip (must be checked

by an authorized personnel).

Off: Good LED strip.

Battery Fault

Οff: Battery OK.

Blink (With Charge LED ON): Autonomy or

low battery problem (the battery must be

replaced).

Blink (With Charge LED Off): No charging

current or disconnected battery.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personnel only, after a mains interruption.

2. The device must be connected to the

mains p o w e r supp l y t h rough a fus e

dependent on the total amount of the line’s

power load.

3. In case of battery or lamp replacement,

these must be replaced by parts of the same

type, by the manufacturer or by a competent

person.

4. In case of inactive use for a period greater

than 2 months, disconnect the battery by

pulling out the battery’s connector.

5. I s not allowed to discard batteries t i

into common trash bins, they must

b e d i s c a r d e d o n l y i n b a t t e r y

recycling points. Do not incinerate.

INSTALLATION

To install the luminaire follow the installation

instructions on page 3.

923577007_09_001

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the

mains power supply or not.

Non Maintained operation: The luminaire lights its illumination source, only in power supply’s

failure.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated

90: 1.5 hour duration

180: 3 hour duration

Page 3 from 5

Cable gland Photo 1 Photo 2

External

switch

Controlled operation of the luminaire

INSTALLATION INSTRUCTIONS

Link

Permanent maintained operation

1. Remove the front cover by unscrewing the retaining screws. Remove the acrylic plate.

2. Always use in any case round mains cable, with a diameter of 12-14mm (H05RN-F type

4x1mm² or any other type, at least equal to it’s mechanical and electrical properties).

ATTENTION!! The cable must not be deformed in any way (This requirement is important

to ensure the tightness isolation IP 66). Pass the round cable through the cable gland and

tighten it all the way.

3. Unfasten the screw to remove the plastic cap (photo1) and connect the battery’s cable as

shown in the photo 2. Replace the plastic cap and fasten the retaining screw.

4. Connect the mains cables as shown in figures 5 and 6. Yellow wire to GND, blue to N, brown

to L and black for maintained operation. The black wire can be connected to an external switch

to control the maintained or non maintained operation of the luminaire. For permanent

maintained operation use three wires to power the luminaire, GΝD for ground N for neutral, L for

live wire and link the brown and black wire to the same terminal.

5. Refit the acrylic plates and the front cover by installing the removed screws in step 1.

6. Power on the device.

923577007_09_001

Page 4 from 5

MOUNTING

The luminaires of this series can be mounted in parallel to the wall of the tunnel (single sided)

for indicating exit routes or vertically to the wall for indicating the position of exit routes or the

position of emergency phones There is also, after request, capability for installation to the wall .

with an angle.

Single sided

luminaire

mounted parallel

to the wall with

indication for

the distance of

the escape exits.

Double sided

luminaire

mounted vertically

to the wall with an

angle with

indication of

escape exit.

Mounting Examples

Double sided

luminaire mounted

vertically to the wall

with indication of

emergency phone.

Single sided

luminaire

mounted in

parallel to the

wall above the

exit door .

TYPICAL SYMBOLS

Except for typical symbols all luminaires can be constructed after request with

any other symbols.

Escape routes Escape exit Emergency phone

923577007_09_001

Page 5 from 5

LED MODULE CHARACTERISTICS

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Olympia Electronics S.A

50 °C max. across the board

Cable connection with polarity

11.6-14.4VDC

5.2W

2809153

GR-577/L/15/ST/WP/O GR-577/L/15/ST/WP

A-1900

Test card

Manual TEST or Resetting Errors with the A-1900 Test card (not included and is available

only after request). In order to test or reset the device you must place the card on the side of the

indications and remove it instantly for TEST or remove it after the reset is conducted (the

indications light in sequence).

LED INDICATIONS

Battery replacement

It can be done only by a competent person and after the mains interruption.

Step 1. Remove the front cover by unscrewing the retaining screws. Remove the acrylic plate.

Step 2. Unfasten the screws to remove the plastic cap and the battery’s plastic holder.

Step 3. Remove the old battery and place a new on of the same type and characteristics.

Connect the battery’s cable as shown in the photo.

Step 4. Replace the removed parts (previous steps 1,2).

2 3

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty

is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which

accompanies each product. This warranty ceases to exist if the buyer does not follow the technical

instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods

provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully

agreed to them in writing. Products that have been damaged can be returned to the premises of our

company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the

buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the

buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

923577007_09_001

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de olympia electronics

olympia electronics

olympia electronics ZLD-28/EM/MAR Manual de usuario

olympia electronics

olympia electronics KLD-30/CBS/24V/ADR Manual de usuario

olympia electronics

olympia electronics GR-938/15L/ADR Manual de usuario

olympia electronics

olympia electronics RT-15 Manual de usuario

olympia electronics

olympia electronics KLD-30/ST/ADR Manual de usuario

olympia electronics

olympia electronics ZLD-28/EM/ADR Manual de usuario

olympia electronics

olympia electronics GR-940/15L Manual de usuario

olympia electronics

olympia electronics SLL-1001/WP Manual de usuario

olympia electronics

olympia electronics LLB-26/CBS/24V/ADR Manual de usuario

olympia electronics

olympia electronics GR-316/15L/MAR Manual de usuario

olympia electronics

olympia electronics GR-940/15L Manual de usuario

olympia electronics

olympia electronics GRL-21/H/90 Manual de usuario

olympia electronics

olympia electronics GR-1938/4P Manual de usuario

olympia electronics

olympia electronics GRL-37/90/WL Manual de usuario

olympia electronics

olympia electronics GR-315/15L Manual de usuario

olympia electronics

olympia electronics POWER LIGHT Series Manual de usuario

olympia electronics

olympia electronics TUV COMFORT LIGHT Series Manual de usuario

olympia electronics

olympia electronics GR-938/30L Manual de usuario

olympia electronics

olympia electronics GR-938/4P Manual de usuario

olympia electronics

olympia electronics GRL-37/90/WP/WL Manual de usuario

olympia electronics

olympia electronics GRL-37/90 Manual de usuario

olympia electronics

olympia electronics SLD-28/SP Manual de usuario

olympia electronics

olympia electronics GR-460 Manual de usuario

olympia electronics

olympia electronics OLY-1004/LT/WP Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

olympia electronics GR-577/L/15/ST/WP Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas