Olivetti EXPLOR@ 950 LED Manual de usuario
Web Cash
EXPLOR@ 950 LED
Code: Y116500-1
SERVICE MANUAL
PUBBLICATION ISSUED BY:
Olivetti S.p.A.
Gruppo Telecom Italia
Via Jervis, 77 - 10015 Ivrea (TO)
Copyright © 2014 Olivetti
All rights reserved
PREFACE
This manual, intended for Explor@950 LED system installation and servicing technicians, contains all the
information necessary for correct installation and maintenance of the product.
SUMMARY
This manual is divided into following chapters.
•Chapter 1 – Provides general information about the system and connection of peripherals.
•Chapter 2 – Describes the technical specifications of the product.
•Chapter 3 – Describes servicing disassembly and reassembly procedures
LIABILITY DISCLAIMER
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use or inability to use the product or documentation, even if advised of the possibility of such
damages.
The information in this document is subject to change without prior notice in order to improve reliability, design
and function and does not represent a commitment on the part of the manufacturer.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this
manual may be reproduced by any mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
All trademarks are property of their respective owners.
PREREQUISITES
The approach to the topics covered in this manual requires knowledge of similar products.
REFERENCES
Spare Parts Catalogue Explor@ 950 LED - code Y116510-2
Product Support Plan Explor@ 950 LED - code 808165-00
Product Logistic Support Explor@ 950 LED – code 808176-00
DISTRIBUTION: General
FIRST EDITION:July 2014
Y116500-1 Service Manual III
Page Intentionally blank
CONTENTS
CHAPTER 1 - HARDWARE SETUP..................................................................................................................1-1
PACKING CONTENTS ......................................................................................................................................1-1
QUICK TOUR .....................................................................................................................................................1-2
Front View and Rear View................................................................................... 1-2
LED Indicator....................................................................................................... 1-2
Back Panel I/O..................................................................................................... 1-3
BASIC PERIPHERALS INSTALLATION ..........................................................................................................1-3
CUSTOMER DISPLAY.......................................................................................................................................1-6
A. Hardware Installation ...................................................................................... 1-6
B. Customer Display Power Supply Configuration............................................. 1-7
MSR............................................................................................................................ 1-8
2ND DISPLAY................................................................................................................................................... 1-10
Base Type 2nd Display Kit Installation ............................................................... 1-11
Pole Type 2nd Display Kit Installation ................................................................ 1-15
2nd Display Power Supply Configuration ........................................................... 1-18
TURN ON THE DEVICE.................................................................................................................................. 1-19
CONNECTIONS .............................................................................................................................................. 1-20
Mother board connections................................................................................. 1-20
I/O DEFINITION............................................................................................................................................... 1-21
Power Connector............................................................................................... 1-21
Serial Port (COM 1, 2 and 5)............................................................................. 1-21
Cash Drawer...................................................................................................... 1-22
Connector .......................................................................................................... 1-22
Cash Drawer Control......................................................................................... 1-22
BIOS CONFIGURATION................................................................................................................................. 1-23
Serial Port Configuration ................................................................................... 1-23
Video Function Configuration ............................................................................ 1-26
CHAPTER 2 - SPECIFICATION ........................................................................................................................2-1
EXPLOR@950 LED- TROUBLESHOOTING ....................................................................................................2-3
System errors ...................................................................................................... 2-3
Peripheral errors.................................................................................................. 2-4
CHAPTER 3 - DISASSEMBLING PARTS.........................................................................................................3-1
SEPARATE THE BASE AND OPEN THE DEVICE ..........................................................................................3-1
MAINBOARD SIDE COMPONENTS REPLACEMENT ....................................................................................3-2
SMONTAGGIO DEL GRUPPO VIDEO.............................................................................................................3-8
HDD REMOVING ............................................................................................................................................ 3-10
Y116500-1 Service Manual v
Page Intentionally blank
Chapter 1 - HARDWARE SETUP
PACKING CONTENTS
1. EXPLOR@950 LED X 1
5. Recovery DVD X 1
2. Power Adapter X 1
6. Cable Cover X 1
3. Power Cord X 1
7. Safety and Disposal Information X 1
4. Drive and Utility DVD X 1
Y116500-1 Service Manual 1-1
QUICK TOUR
Front View and Rear View
LED Indicator
The Power indicator will glow green when power is on.
The HDD indicator will blink green when the HDD is accessed.
The LAN indicator will blink green when transferring data though the LAN.
1-2 Service Manual Y116500-1
Back Panel I/O
BASIC PERIPHERALS INSTALLATION
1. All cables and wires from peripherals to the POS device are recommended to be fed through the base in the
direction as shown below.
WARNING: Before the cable cover is removed, please make sure the power is off! Disconnect the Power Cord
from the socket.
Y116500-1 Service Manual 1-3
1. Power Adapter
Connect the DC cable to the DC in jack.
2. Computer Mouse and Computer Keyboard
Connect your computer mouse and keyboard to USB 1/2, UBS 3/4 or the KB/MSport, depends on which type
of computer mouse/keyboard used.
3. USB ODD
Connect your USB ODD to USB 1/2 or UBS 3/4 port.
1-4 Service Manual Y116500-1
Tabla de contenidos
Otros manuales de Terminal táctil de Olivetti
