OHAUS Valor V11P3 Manual de usuario

Valor™ 1000 Series

Instruction Manual

Serie Valor™ 1000

Manual de Instrucciones

Série Valor™ 1000

Guide de I’utilisateur

Serie Valor™ 1000

Bedienungsanleitung

Serie Valor™ 1000

Manuale d’instruzioni

OHAUS ValorTM 1000 Series EN-1

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the

Ohaus ValorTM 1000 Series Scales. Please read the manual completely before using

the scale.

1.1 Safety Precautions

Please follow these safety precautions:

• Verify AC Adapter input voltage matches the local AC power supply.

• Do not immerse the scale in water or other liquids.

• Do not operate the scale in hostile environments.

• Do not drop loads on the platform.

• Do not place the scale upside down on the pan.

• Service should only be performed by authorized personnel

• Disconnect the scale from the power supply when cleaning

1.2. Controls

Figure 1-1. Controls.

EN-2 OHAUS ValorTM 1000 Series

TABLE 1-1. CONTROLS

Item Description

1Low battery indicator

2Battery charge indicator

3Level Bubble

4Center of Zero, NET, Stability Sum icons

57-segment, 6 digit backlit LCD w/ units of measure enunciators

6Over, Under , Accept Check weigh indicators

7Control Buttons

8Adjustable feet

9Power input jack

10 On/Off Power Switch

TABLE 1-2. CONTROL FUNCTIONS.

Button Action Function

Short Press Sets display to zeroZERO

Menu Press Confirms settings

Short Press Tares weight of item on panTARE

Menu Press Decrement over and under settings

Short press Stores displayed weight in accumulation memory

Display accumulation data when display is at zero

Menu Press Increment over and under settings

M+

Units

Long Press Change unit of measure while already pressing

SELECT button

Short press Shift to next digit when setting over and under valuesSELECT

Units

Long Press Change unit of measure together with short press of

M+ button

OHAUS ValorTM 1000 Series EN-3

2. INSTALLATION

2.1 Package Contents

• Valor 1000 Scale

• Stainless steel Pan

• AC Power Adapter

• Instruction Manual

• Warranty Card

2.2 Location

Use the scale on a firm, steady surface. Avoid locations with excessive air current,

vibrations, heat sources, or rapid temperature changes. Adjust the leveling feet so

the bubble is centered in the circle.

Level Bubble 4xLevel

Figure 2-1. Leveling the Scale.

2.3 Power

Connect the AC Adaptor to the AC mains supply. Connect the plug to the DC jack on

the bottom of the scale. The scale may be operated on the AC mains supply or the

built in rechargeable battery. The scale must be turned on to charge the battery.

DC Jack

Figure 2-2. Power Connection

EN-4 OHAUS ValorTM 1000 Series

2.3.1 Battery Power

The scale can be operated on the internal rechargeable battery when AC power is not

available. The scale will automatically switch to battery operation if there is a power

failure or the power cord is removed.

Before using the scale for the first time, the battery should be fully

charged for up to 12 hours. During charging, the battery Indicator

displays the charge level (see table 1-1), and the scale can be operated

during charging. The battery is protected against over charging and the

scale can remain connected to the AC power line.

NOTE:

• Charging the scale must only be performed in a dry environment

CAUTION: Battery is to be replaced only by an authorized Ohaus service

dealer

Risk of explosion can occur if replaced with the wrong type or connected

improperly

Dispose of the lead acid battery according to local laws and regulations

2.4 Initial Calibration

When the scale is operated for the first time, a Span calibration is recommended to

ensure accurate weighing results. Before performing the calibration, be sure to have

the appropriate calibration weight.

Refer to section 4.3 for Span calibration procedures.

OHAUS ValorTM 1000 Series EN-5

3. OPERATION

3.1 Turning Scale On/Off

To turn the scale on, flip the toggle switch below the right front keyboard. The scale

performs a display test, momentarily displays software version, and then enters the

active weighing mode. To turn the scale off, toggle same switch to off position.

3.2 Zero Operation

Zero is set under the following conditions:

• Automatically at Power On (initial zero).

• Manually by pressing the ZERO button.

Press the ZERO button to zero the weight display. The scale must be stable and

weight +/- 2% of capacity to accept zero operation.

3.3 Manual Tare

Place a container on the weighing pan, then press TARE. The display will show a net

value of “0”. To clear the Tare value, press TARE with the pan empty.

3.4 Weighing Mode

Use this mode to measure the weight of a sample in the selected unit of measure.

Press and hold SELECT then press M+ Unit until the desired unit icon is displayed.

Press ZERO to set the display to zero. Put an empty container on the pan, and then

press TARE to tare the container weight. Add material to the container. The display

shows the weight of the material in selected unit of measure.

EN-6 OHAUS ValorTM 1000 Series

3.5 Accumulate Mode

Use this mode to store the weight and HI, LO, SUM statistics from a series of

samples.

Press ZERO to set the display to zero.

Place the sample on the pan, wait for stabilization.

Press M+ to store the weight of the sample. Storage is confirmed by the display [n--

--x], where x is the sample number. The enunciator above SUM text will illuminate to

let user know there are readings in memory. Remove the sample, wait for stable zero

reading, then place the next sample on the pan. Press M+ to store the weight of the

next sample. Repeat this process until all samples have been weighed.

Review the accumulation data by pressing M+ when the display is at zero.

The display shows the number of samples [n----x]

Press M+ to view the maximum sample weight [Hxxxxx].

Press M+ to view the minimum sample weight [Lxxxxx].

Press M+ to view the sum of weights [xxxxx].

Press M+ to return to weighing.

Clear the accumulated data by pressing ZERO when the number of samples is

displayed. Note – when stored values are in memory, unit of measure cannot be

changed.

3.6 Check Weigh Mode

Use this mode to compare samples to a target weight range.

Press ZERO to set the display to zero. Place a sample on the pan and read the

weight and under / accept / over status on display. (Refer to section 4.1 to set

limits)

3.7 Changing Units of Measure

Press and hold the SELECT key, and while still holding the SELECT key, press M+

button to display the next available measuring unit. Repeat process to scroll through

all units.

OHAUS ValorTM 1000 Series EN-7

4. SETTINGS

The scale allows the user to customize several settings including check weigh limits,

backlight operation and calibration.

4.1 Over and Under Limits

Press and hold SELECT, and while still pressing SELECT, press ZERO until [SET---] is

displayed.

Press SELECT to display [SET-F0]

Press ZERO to view the upper limit [000000].

Press SELECT (§), M+ (©), Tare (ª) to edit the digits of the upper limit.

Press ZERO to confirm the setting and display the lower limit [000000].

Press SELECT (§), M+ (©), Tare (ª) to edit the lower limit.

Press ZERO to confirm the lower setting and display will show Run---X where x is the

alarm setting. In this case x=

0 = Turns off check weigh mode

1 = under / accept / over indicators are displayed, alarm beeps when weight is

outside accept range.

2 = under / accept / over indicators are displayed, alarm beeps when weight is

within accept range.

3 = under / accept / over indicators are displayed, alarm is off.

Press TARE to change the alarm to desired setting.

Press ZERO to confirm setting and display [End]

When [End] is displayed, Press and hold SELECT, and while still pressing SELECT,

press ZERO key to return to weighing.

4.2 Backlight

Press and hold ZERO button until [b9---x] is displayed, where x=

0 = backlight is turned off

1 = backlight is on during weighing (15 seconds of no activity)

2 = backlight is always on

Press TARE to change the setting. Press ZERO to confirm the setting and return to

weighing.

EN-8 OHAUS ValorTM 1000 Series

4.3 CALIBRATION

Span Calibration:

Turn on the scale. When display flashes all segments ("888888") press and hold

ZERO and SELECT at the same time until "SET--- " is displayed at the end of power

on sequence. Press the SELECT key until "SET-F1" is shown on the display.

Press ZERO key to display "A____x" (x=divisions in grams:1,2,5,10.20.50).

Press ZERO key to accept the default division setting which is shown on the display.

Do not change default.

Display shows "b____x" (x=decimal point:0,1,2,3,4). Press ZERO key to accept the

default decimal point setting which is shown on the display. Do not change default.

Display shows "Cxxxxx" (xxxxx=Capacity of scale). Press ZERO key to accept the

default Capacity setting which is shown on the display. Do not change default.

Display shows "dx" (x=Zero tracking setting:0-9 from 0.125d to 1.25d). Press

ZERO key to accept the default setting which is shown on the display.

Press ZERO and display will show "Load 0". Make sure pan is empty then press

ZERO key to accept. Display will show "CAL 0" briefly, then "Load F” will be

displayed.

Press ZERO to display "Fxxxxx" (xxxxx=Span weight ). To accept default span

weight, put displayed weight on the scale, and press ZERO to accept.

If span weight is not available, user can select a lower span calibration point value.

Use the SELECT (scroll to next digit), TARE (decrease blinking digit) and M+

(increase blinking digit) keys to increment or decrement span calibration values.

Once desired span calibration weight is set, place displayed weight on the scale,

and press ZERO to accept. After completion, scale will be in weighing mode.

To abort calibration at any point, turn scale off. To restart calibration, follow

calibration procedure from beginning.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Escala de OHAUS

OHAUS

OHAUS Defender D12RQR Manual de usuario

OHAUS

OHAUS PS121 Manual de usuario

OHAUS

OHAUS CHAMP II BASE Manual de usuario

OHAUS

OHAUS Catapult 1000 Series Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS Ranger Count 3000 Series Manual de usuario

OHAUS

OHAUS HP-120 Manual de usuario

OHAUS

OHAUS RC31P1502 Manual de usuario

OHAUS

OHAUS ES6R Manual de usuario

OHAUS

OHAUS Compass CR221 Manual de usuario

OHAUS

OHAUS PX Series Manual de usuario

OHAUS

OHAUS JE 120 Manual de usuario

OHAUS

OHAUS CL Series Manual de usuario

OHAUS

OHAUS ANALYTICAL Plus Series Manual de usuario

OHAUS

OHAUS VALOR 5000 H Series Manual de usuario

OHAUS

OHAUS 4000W Series Manual de usuario

OHAUS

OHAUS SHRK07AL1 Manual de usuario

OHAUS

OHAUS Navigator Manual de uso y cuidado

OHAUS

OHAUS ES series Manual de usuario

OHAUS

OHAUS Valor 3000 Manual de usuario

OHAUS

OHAUS RE-C series Manual de usuario

OHAUS

OHAUS TROOPER SCALE Manual de usuario

OHAUS

OHAUS Scout STX Manual de funcionamiento

OHAUS

OHAUS BW1.5US Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario