Nussbaum SPRINTER Manual de instrucciones

Unpacking & Installing your Sprinter

Things you will need (not provided):

-Side cutters

-Utility knife

-Hammer

-3 mm Allen wrench

-Hammer

-Screwdrivers (both Phillips and Straight)

-Snap ring pliers

-220v plug. Not supplied. Unit requires 20 amp 208/230volts. Your available 208/230v socket might

vary.

-2 gallons AW32 Hydraulic Fluid. DO NOT USE TRANSMISSION FLUID

-Board (to push lift off pallet. The longer the board, the more leverage you have, the easier it is)

Weight & Dimensions of Sprinter Box: 83”X 63”X 18”1,100 Pounds

It would be smart to ask the trucker at delivery to use his pallet jack to position the box with the wide

side across the driveway/parking lot. It will make it easier for you when it comes time to remove the lift.

You need to cut the bands and remove the top of the crate.

This is not how it looks as you unpack it, but these are the contents of your package:

4 2” White “Crushblocks” (THESE ARE NOT PACKING MATERIALS, THEY ARE THE LIFTING BLOCKS

FOR THE LIFT. DON’T THROW THEM AWAY!)

4 Approach / Exit Ramps

1 Front swivel wheel

1 Tow Bar

1 Tow Bar Hanger

1 Bag Hardware (8 axle pins, 16 external snap rings)

1 Owner’s Manual

2 Rear Wheels (not shown as they are mounted under the platform on the lift scissor mechanism)

Make sure to take the end of the crate off where the hoses are attached. This is the front end of the

lift where the front swivel wheel will attach as it comes off the crate. Take care not to hit the hoses with

the hammer when removing the end.

Using the board, start prying the lift off the crate. When the front torsion bar of the lift clears the front

of the crate, place the front swivel wheel into position. This will help as the lift “rotates” off the crate

and onto the ground.

Note the box laying down. Set up the box with the wheels of the control station down, remove packing

material and simply roll it out.

Take off the top cover using the 3mm Allen wrench on the four screws holding it on. Be careful at this

point not to drop the cover as wires could be pulled from the up/down switches housed within.

Locate the main power lead, straighten out and feed it down the back of the control unit and out of the

bottom.

Attach your specific plug. The unit requires a 208/230 volt, 20 amp circuit which the wiring will safely

handle. We realize all shops have different plug configurations (i.e. welder plug, compressor plug, A/C

plug) and most of these require more amperage than your Sprinter lift. Note that if you choose to plug

the unit in one of these outlets, the breaker (30, 40, or 50 amp) will not protect the wiring in the lift.

Wires are Blue, Brown and Yellow/Green. Blue and Brown are your “hot” leads and Yellow/Green is

ground

Remove the dipstick and add 2 gallons of AW32 Hydraulic fluid which is available at most auto parts

stores. Pay NO attention to the level on the dipstick, 2 gallons is the appropriate amount of fluid.

Attach the Quick Connect hydraulic hoses from the lift to the control stations. IT MAKES NO

DIFFERENCE WHICH HOSE IS CONNECTED TO WHICH OUTLET. The system is the Nussbaum exclusive

“Twin Cross Master Hydraulic” system which operates perfectly no matter the hose connection.

Turn on the lift and raise to full height.

Attaching the ramps can be the most challenging item during set up.

1) Make sure the ramps are in the correct positions. The lock release lever on the ramp should be

facing the outside of the lift when installed

2) Attach 1 snap ring on each pin

3) Start two pins from the inside/out in a ramp

4) Turn over and slide pins through openings on platform ends

5) Attach remaining snap rings on the outside of pin

6) To release the ramp, lift the release pin while lifting the end of the ramp slightly, then lower

Putting on wheels.

The lift must be raised to a minimum of 15” to attach wheels for portability. The rear wheels are

stored on top of the plate under the rear scissor. Take them off and place in holes on the side of the rear

scissors.

Place the front swivel wheel over the front transverse bar. There is a “lockdog” built into the transverse

bar which the swivel wheel will slide over.

Lower the lift fully and all three wheels will engage.

Pull to desired location. You can either set the control unit on top of the platforms to change locations

or disconnect the hoses and move separately.

(Note the edge of the driveway. This is what happens if you place the lift with the long side at the edge

of the driveway instead of across it.)

This handy hanger can be mounted in a convenient location to store your tow bar on.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de elevación de Nussbaum

Nussbaum

Nussbaum UNI-LIFT 3500 NT ND Manual del operador

Nussbaum

Nussbaum SMART LIFT 2.30 SL Manual de usuario

Nussbaum

Nussbaum OTTO 18 Manual de usuario

Nussbaum

Nussbaum HF 3S 12000 Manual de usuario

Nussbaum

Nussbaum POWER LIFT HF 7000 Manual de usuario

Nussbaum

Nussbaum ATT COMBI LIFT 4.40 S Manual de usuario

Nussbaum

Nussbaum JUMBO HFK 7000 Guía de inicio rápido

Nussbaum

Nussbaum 4.55 SL Manual del operador

Nussbaum

Nussbaum POWER LIFT HF 4600 Manual de usuario

Nussbaum

Nussbaum 2.60 HL SST Manual del operador

Nussbaum

Nussbaum 4.50 SL Manual del operador

Nussbaum

Nussbaum 2.35 TSK Manual del operador

Nussbaum

Nussbaum UNI-LIFT 4000 MB Manual de usuario

Nussbaum

Nussbaum Sprinter NT Manual del operador

Nussbaum

Nussbaum UNI-LIFT 5000 CLT PLUS Manual del operador

Nussbaum

Nussbaum TSK 8000 Manual de usuario

Nussbaum

Nussbaum SPL 8 Series Manual de usuario

Nussbaum

Nussbaum HF 3S 8000 Manual de usuario

Nussbaum

Nussbaum 2.30 SPL Manual del operador

Nussbaum

Nussbaum HL 2.30 NT Manual de usuario

Nussbaum

Nussbaum 4.65H Plus Manual del operador

Nussbaum

Nussbaum JUMBO HF 7000 Manual de servicio

Nussbaum

Nussbaum ATT HYMAX S 3000 Manual de usuario

Nussbaum

Nussbaum TOP LIFT TSK 12000 DJ Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario