NTI ENVIROMUX E-5D Manual de usuario

E-xD: RESTORE DEFAULTS VIA RS232

This procedure is provided to enable the administrator to restore defaults to the E-5D\16D using the “RS232” port.

Note: This procedure has been tested to work properly using Microsoft®HyperTerminal. We cannot confirm whether

other terminal programs will give satisfactory results.

1.Connect one end of a CAT5 patch cable (supplied) to the port labeled “RS232” on the rear of the E-16D (or front of the E-5D).

Plug the other end of the CAT5 cable into an RJ45-to-DB9F adapter (supplied), and connect the adapter to the RS232 port on the

control terminal.

Connect a terminal for direct RS232 serial communication

2. Using the terminal connected to the ENVIROMUX, start the terminal program (e.g. Windows HyperTerminal) and configure it

as follows:

direct connection (using the appropriate CPU local serial Com port)

115200 bps

8 bits

no parity

1 stop bit

no flow control

VT100 terminal mode.

3. Power ON the ENVIROMUX and as the ENVIROMUX begins to boot, press and hold the <Tab> key. (If you fail to press this

key in time the system will continue booting and you will have to power OFF the ENVIROMUX and start over.)

Erase the configuration of the ENVIROMUX

4. At the “SEMS-16>” prompt, type;

SEMS-16> nand erase config

5. Press <Enter> key.

The ENVIROMUX will erase all configuration settings and restore the ENVIROMUX to factory default settings. ALL USER

CONFIGURATION AND SENSOR CONFIGURATION SETTINGS WILL BE LOST.

When finished, the “SEMS-16>” prompt will return.

6. At the prompt, type reset and press <Enter>. The ENVIROMUX will restart.

and erase confi

eset

Restoring the default configuration of the ENVIROMUX

7. As the ENVIROMUX restarts, it will restore defaults (as shown in image above) and then present the ENVIROMUX login screen

(below).

Text Menu Login Screen

At this point you can either access the ENVIROMUX using the Device Discovery Tool (found on the manual CD and our website

at http://www.networktechinc.com/download/d-environment-monitor-16.html ) to change the network settings back to what they

were, or you can login to the text menu (below) using the default administrative user “root” and password “nti”.

From the text menu, to change the network settings, enter <4>, then <1> to get to the network configuration menu.

Enter your settings.

Be sure to <Tab> to the Save and press <Enter> before exiting the menu.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de NTI

NTI

NTI ENVIROMUX Series Manual de usuario

NTI

NTI ENVIROMUX Series Manual de usuario

NTI

NTI ENVIROMUX Series Manual de usuario

NTI

NTI ENVIROMUX-16D Manual de usuario

NTI

NTI ENVIROMUX Series Manual de usuario

NTI

NTI USB-A+A-5M Manual de usuario

NTI

NTI E-BEEP2-x Manual de instrucciones

NTI

NTI ENVIROMUX-16D Manual de usuario

NTI

NTI ENVIROMUX Series Manual de usuario

NTI

NTI ENVIROMUX-MINI-LXO Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario