NPC ReverseTap RD BF1 Manual de usuario

ReverseTap In-counter Models

Installation Guide

( KEGERATOR SYSTEM )

Incounter Models

RD BF1

RD SF1

RD SF2

RD SF3

RD SF4

V2.0

ReverseTap In-counter Models Installation Guide ( Kegerator )

1. Decide a desired install position and cut out by the size shown below.

- Please refer to ReverseTap website for hole dimension for each dispenser model.

* Required tools : Drill, Jig-saw, Driver, Hose cutter, Knife, Hose clamps, etc.

V2.0

*Hand-drill

*Jig-saw

*Screw driver

*Hose-cutter

*Wrench

*Clamps

*Tape

*Scissors

*Tapeline

Model RD-BF1 RD-SF1 RD-SF2 RD-SF3 RD-SF4

Vertical 175mm 285mm

Horizontal 175mm 164mm 300mm 436mm 572mm

- To be installed on flat and smooth surface. ( Insulating cold air is a critical issue in kegerator system )

- Be careful not to get hurt by the flying debris during the cut out process.

( Wearing safety goggles is recommended )

- Clear the debris after the cut out process.

2. Connect the Flow meter to the Solenoid valve set.

①Remove a lid from the solenoid valve set and insert the flow sensor.

( Please aware that the flow sensor is to be inserted as the indicated direction only )

②Insert the flow sensor connector to the Board assembled with solenoid valve set.

( The flow sensor connector and the Board socket are 3-pin )

③Organize the cables.

( The flow sensor cable can be neatly wrapped around the solenoid valve set before inserted to the socket. )

* Please be careful not to have substances into the flow sensor.

①①

②③

3. Put ReverseTap on the desired surface.

- Silicone is wrapped around the bottom borders of the dispenser for sealing purpose.

Please be careful not to have it escape.

*Silicone for sealing

ReverseTap In-counter Models Installation Guide ( Kegerator )

4. Connect DC 24 V CONNECTOR CABLE with the main power cable of ReverseTap.

①The end part of DC 24 V CONNECTOR CABLE is a waterproof connector.

②DC plug of DC 24 V CONNECTOR CABLE is not waterproof, therefore keep it away from water and tape

around the joint part.

*DC 24 V CONNECTOR CABLE

* Organize the cables after connecting DC 24 V CONNECTOR CABLE with ReverseTap.

②

V2.0

6. Connect the power and run a function test.

-①ReverseTap power turns ON as soon as power is connected.

-②To individually turn ON/OFF each unit, press START/STOP button in its keypad for a few seconds.

-③Check if a cup is easily inserted and properly sensed.

-④Check if LED is lit properly.

-⑤Check if solenoid valves are opened with clicking sound.

-⑥Check if all buttons in each key pad work properly. ( the sensitivity of each button may slightly differ )

* Press START/STOP button in its keypad for a few

seconds to turn ON/OFF units individually.

* Assemble PROTECT COVER and NOZZLE COVER.

* Insert a cup to check LED, Solenoid valve functions correctly, and check all buttons work fine.

①

②②

③~⑥

ReverseTap In-counter Models Installation Guide ( Kegerator )

7. Tightly fasten main body of ReverseTap with the included Bracket set to the desired surface.

①Assemble bolts(M4 X 100mm) with wing nuts.

②Locate fastening clamps beneath the kegerator and fasten the bottom part of the dispenser with bolt-wing nut

assemblies. ( Total of 4 ea of fastening clamps are included in the product )

③Fasten wing nuts to tightly fix ReverseTap to the kegerator with fastening clamps.

( Loosened wing nuts may cause cold air escape and foreign substances flow in )

* Check the number of bracket sets and assemble bolts with wing

nuts.

①

②

③

* Bracket set and bolts fastening spots

V2.0

8. Connect beverage tubing to the flow sensor and the other end of beer line with a coupler.

①Flow sensor has fitting assembled already for 1/4 inch beer line.

( The inlet of flow sensor is 5/16 inch )

②For draft beer line : Approximately 3m long 1/4 inch(O.D) beer line must be used.

( Wind up a beer line several times and finish with taping for organizing )

ReverseTap In-counter Models Installation Guide ( Kegerator )

9. Connect the Drain hose set.

- Be careful not to bend drain hose too much, and organize for the easy drain.

- Connect the end of the drain hose to the sewers or a drain bucket.

5/16 inch

V2.0

ReverseTap In-counter Models Installation Guide ( Kegerator )

10. Install a coupler to a keg and set the CO2 gas pressure.

①Install a coupler to a keg and open the mid-valve, then set the gas pressure.

* Recommended pressure for draft beer : 13 psi ~ 16 psi

②Lock the gas pressure setting by fastening the lock nut.

③Gas pressure tend to adjust itself after some drinks are dispensed, so some calibrations are required initially.

①

②

11. Settings (Preset Mode, Dispensing Amount, FOB Mode)

- Now all steps for installing the ReverseTap dispenser is complete.

-Kegs must be cooled down to 2℃~4℃ for proper use of ReverseTap.

- For initial use, initial settings must be done in steps as the following.

- When a cup is inserted for the first time, the following screen will show due to the FOB Mode (Function for blocking

foam popping )

-Press the ‘STOP’ button to deactivate FOB Mode, and proceed in order of Cleaning →PRESET →Dispensing Amount →

FOB Mode Activation ( For detailed information, please refer to the S/W Manual or Quick User’s Manual)

Cleaning PRESET Dispensing

Amount FOB

* FOB Mode is activated in

the first cup insertion.

* Press the ‘STOP’ button to

deactivate the FOB Mode.

* Remove foam from the tubing

by operating Cleaning Mode.

* Measure the flow rate by

operating PRESET Mode.

* Enter the desired volume of

dispensing.

* Activate FOB Mode. * Confirm the FOB Mode turned

ON in the Standby screen.

V2.0

ReverseTap Customer Service

•Information regarding Certified Service Center (CSC) can be collected via regional distributors

and our website. ( www.reversetap.com )

Trademarks

•ReverseTap and ReverseTap logo are registered trademarks of NPC Co., Ltd.

•Other names and marks are the property of their respective owners.

Refunds / Exchange / Warranty Policy

•Refunds or exchange may be offered within 15 days after purchase if the product cannot be

used due to its defect.

This does NOT apply if the customer is responsible for the damage due to one’s carelessness.

NPC CO., LTD.

129 Idang-ro, Gunpo-si,

Gyeonggi-do, Republic of Korea 15853

www.reversetap.com

www.youtube.com/reversetap

www.facebook.com/reversetap

This manual is protected under international copyright laws. No part of this

guide may be reproduced, distributed, translated, or transmitted in any form

or by any means, electronic or mechanical, including photocopying, recording,

or storing in any information storage and retrieval system, without the prior

written permission of NPC Co., Ltd.

Webpage QR Code

FDA certified

by SGS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Kegerator de NPC

NPC

NPC ReverseTap Manual de usuario

NPC

NPC ReverseTap RD-B1 Manual de usuario

NPC

NPC ReverseTap Instrucciones de instalación

Manuales populares de Kegerator de otras marcas

Nostalgia Electrics

Nostalgia Electrics KEG9000DTSS Manual de usuario

Nostalgia Electrics

Nostalgia Electrics KRS2100 SERIES Manual de usuario

AMD DIrect

AMD DIrect SSRFR-24DK Manual de usuario

PolyKeg

PolyKeg PRO Manual de usuario

PolyKeg

PolyKeg PRO one-way keg Manual de usuario

KegLand

KegLand Fermzilla Manual de usuario

EdgeStar

EdgeStar KC3000 Manual de usuario

Nostalgia Electrics

Nostalgia Electrics Kegorator KRS-2150 Manual de usuario

Nostalgia Electrics

Nostalgia Electrics KEGORATOR KRS-2000 SERIES Manual de usuario

KegLand

KegLand Benchy Carbon KL18210 Manual de usuario

KegLand

KegLand Benchy - Glycol Manual de usuario

Kegco

Kegco Hot Draft KC HDT301 Manual de usuario

Vinotemp

Vinotemp VT-FULLKEG Manual de usuario

Midea

Midea WHS-199BSS1 Manual de usuario

U-Line

U-Line Single Tap Tower Kit Manual de usuario

WILLIAMSWARN

WILLIAMSWARN BrewKeg50 Manual de usuario

EdgeStar

EdgeStar ECK24 Manual de usuario

EdgeStar

EdgeStar BR1500BL Manual de usuario