Novusun CNC NCB01 Manual de usuario
百年品质，值得信赖 —— 您的产品名称
Manual
CNC CONTROLLER BOX
NC
B
0
1
WWW.NVCNC.NET
WWW.NVCNC.NET
M请在这里输入您的公司名称或产品名称
Manual of NCB01
Manual of NCB01
Contects
Chapter 1.Brief Introdution ..........................................................................................................................- 1 -
1.1 Products brief introduction ....................................................................................................................- 1 -
1.2 Specification feature ..............................................................................................................................- 1 -
1.3 Product appearance and dimension........................................................................................................- 1 -
1.4 Notice and Waring .................................................................................................................................- 5 -
Chapter 2.Connection...................................................................................................................................- 6 -
2.1 Connection interface definition..............................................................................................................- 6 -
2.2 Detailed Definition.................................................................................................................................- 7 -
WWW.NVCNC.NET
Chapter 1 Brief Introdution
Manual of NCB01
- 1 -
Chapter 1. Brief Introdution
1.1 Products brief introduction
NCB01 is designed for CNC Amateur. It's a total solution. You only need mechanical
part of CNC machine, connect with NCB01 to constitute a system.
NCB01 is compatible with mach3 by LPT. Using NC200,NCB01 connect with mach3
by USB.
1.2 Specification feature
1) High performance,low prices
2) 4 Axis 4A 1/128 microstep steppermotor driver
3) Spindle driver is 400W BLDC driver without Hall.
4) Maximum Spindle driver motor running speed 12000R/Min
5) LPT controller port.
6) 220VAC power input.
1.3 Product appearance and dimension
NCB01 product appearance pls see picture 1-1 to picture 1-3. NCB01 connect with
NC200 see picture 1-4. NCB01 connect with NC200 and NHC see picture 1-5.
WWW.NVCNC.NET
Chapter 1 Brief Introdution
Manual of NCB01
- 2 -
Figure1-1. NCB01 appearance 1
Figure1-2. NCB01 appearance 2
WWW.NVCNC.NET
Chapter 1 Brief Introdution
Manual of NCB01
- 3 -
Figure1-3. NCB01 appearance 3
Figure1-4. NCB01 connect with NC200
WWW.NVCNC.NET
Chapter 1 Brief Introdution
Manual of NCB01
- 4 -
Figure1-5. NCB01 connect with NC200 & NHC
NCB01's product outline dimension is 118*76*33mm,as picture 1-6 shows.
WWW.NVCNC.NET
Chapter 1 Brief Introdution
Manual of NCB01
- 5 -
Figure1-6. product outline dimension of NCB01
1.4 Notice and Waring
Prohibit staying in the rain, it will cause short-circuit..
Pls use proper voltage power supply and motor.
Note the power supply connection. Prohibit reverse connection of power
supply .
WWW.NVCNC.NET
Chapter 2 Connection
Manual of NCB01
- 6 -
Chapter 2. Connection
2.1 Connection interface definition
Definition of NCB01.see as Figure 2-1.
WWW.NVCNC.NET
Chapter 2 Connection
Manual of NCB01
- 7 -
Figure2-1. NVBDH+panel button speed control+ Panel start/stop control
Mark Definition
1 Spindle Control Panel
2 Estop Button
3 Parallel Control Port
4 Limit Port
5 X axis Steppermotor Port
6 Y axis Steppermotor Port
7 Z axis Steppermotor Port
8 A axis Steppermotor Port
9 Programmable Output Port
10 Probe Port
11 Spindle Port
12 AC power Input Port
13 Main Power Switch
14 Spindle Power Switch
Table 2-1 Block of BOX
2.2 Detailed Definition
1、Spindle Control Panel
This is BLDC driver control panel. Through this panel, you can set BLDC spindle motor
WWW.NVCNC.NET
Chapter 2 Connection
Manual of NCB01
- 8 -
driver's mode. See as manual of NVBD .
2、Estop Button
This button is Estop button. When in an emergency, you can push this button. Estop
button is connected to PIN15 of LPT. Set of ESTOP see as Figure 2-2.
Figure2-2. Set of ESTOP in mach3
3、Parallel Control Port
This is Parallel Control Port of BOX. Mach3 can control machine through LPT port or
through USB port by NC200. Definition of this port see as Table 2-2.
Mark Definition Property
1 PWM, Spindle speed adjust port OUT
2 Step of X axis OUT
3 Dir of X axis OUT
4 Step of Y axis OUT
WWW.NVCNC.NET
Tabla de contenidos
Otros manuales de Controladores de Novusun CNC
Novusun CNC
Novusun CNC NVUMv2.1 Manual de usuario
Novusun CNC
Novusun CNC NCH02 Manual de usuario
Novusun CNC
Novusun CNC NVBDH+ Manual de usuario
Novusun CNC
Novusun CNC NVEMV2 Manual de usuario
Novusun CNC
Novusun CNC NVCM Series Manual de usuario
Novusun CNC
Novusun CNC NC200 Manual de usuario
Novusun CNC
Novusun CNC NVUM_SPv1.1 Manual de usuario
Novusun CNC
Novusun CNC NVUM Manual de usuario
Novusun CNC
Novusun CNC NVUM Manual de usuario
