NovaStar MCTRL 4K Manual de usuario

XI'AN NOVASTAR TECH CO.,LTD.

Statement

Welcome to use the product from Xi’an NovaStar Tech Co., Ltd. (hereinafter

referred to as “Novastar”). It is our great pleasure to offer this manual to help

you understand and use the product. We have striven for precision and reliability

during the compilation of this manual, and the contents of this manual are subject

to change at any time without further notice. If you have any problem during

use or you have any suggestion, please feel free to contact us according to the

contact information provided in this manual. We will do our utmost to satisfy your

needs. We would like to express our sincere appreciation to your suggestions and

make assessment for adoption as soon as possible.

All the intellectual property rights involved in this document belong to NovaStar.

No part of this document may be reproduced or extracted in any form or by any

means without prior written consent of NovaStar. All rights are reserved.

Trademark

is the registered trademark of NovaStar.

Safety Statement

To avoid potential hazards, please use this controller according to regulations.

Power outlet should be installed near the controller and easy to reach. In the

event of breakdowns, non-professionals are not allowed to disassemble the

controller for maintenance. Please contact the after-sales department of NovaStar

timely.

High voltage danger: The operating voltage range of this product is

100-240V AC.

Grounding: This product is grounded through the grounding cord of

power supply. Please keep the grounding conductor well grounded.

Electromagnetic interference: Keep this product far away from

magnets, motors and transformers.

Moisture proof: Keep this product in a dry and clean environment. In

case of liquid immersion, please pull the power plug out immediately.

Keep this product away from flammable and explosive substances.

Prevent liquids or metal fragments from dropping into the product in

order to avoid safety accidents.

XI'AN NOVASTAR TECH CO.,LTD.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment .This equipment should be installed and operated with

minimum distance 20cm between the radiator& your body.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

XI'AN NOVASTAR TECH CO.,LTD.

Table of Contents

1 Appearance...................................................................................................... 1

Front Panel .........................................................................................................................1

Rear Panel ...........................................................................................................................1

2 Signal Connection........................................................................................... 3

3 Dimensions...................................................................................................... 4

4 Operating Motion Instruction....................................................................... 4

5 Main Interface................................................................................................. 5

6 Menu Operation.............................................................................................. 6

Step 1 Input Mode........................................................................................................... 6

Step 2 Input Resolution.................................................................................................. 6

Step 3 Quick Config.........................................................................................................7

Step 4 Brightness Adjustment ..................................................................................... 8

Screen Settings .................................................................................................................9

Display Control .................................................................................................................9

Advanced Settings.........................................................................................................10

Communication Settings .............................................................................................12

Language ..........................................................................................................................12

7 Technical Specifications ............................................................................... 13

8 FAQs and Precautions .................................................................................. 14

XI'AN NOVASTAR TECH CO.,LTD.

-1-

MCTRL4K User‘s Manual

1 Appearance

Front Panel

① : Power button; Press the button for startup. After startup, press and hold the

button for 4~5 seconds to power off.

② : USB interface for connecting USB drives only(unable to connect computers).

③ : Operation screen

④：Knob; Pressing the knob indicates Enter or OK, rotating the knob allows us to

select or adjust.

⑤：BACK; Back to the previous menu.

Rear Panel

XI'AN NOVASTAR TECH CO.,LTD.

MCTRL4K User‘s Manual

-2-

Inputs

DP 1.2 DP 1.2 interface

HDMI 2.0 HDMI 2.0 interface

DUAL DVI-D1/D2 Dual-link DVI interface

Outputs

1~16 16-channel Neutrik Gigabit Ethernet outputs

OPT1~4

4-channel optical fiber outputs

OPT1 is corresponding to Ethernet port 1~8.

OPT2 is corresponding to Ethernet port 9~16.

OPT3 is the backup of OPT1. OPT4 is the backup of

OPT2.

Control

ETHERNET Control interface

USB IN: cascade input or connecting PC;

OUT: cascading next unit.

GenLock

Genlock synchronous signal, making sure the picture

on LED display is in sync with external Genlock

source.

Genlock type: Blackburst

LOOP Genlock loop output

Power

AC 100-240V ～ 50/60HZ AC power interface

Note: Type A(flat) USB interface is not allowed to be connected to control computer

directly.

XI'AN NOVASTAR TECH CO.,LTD.

-3-

MCTRL4K User‘s Manual

2 Signal Connection

Please refer to the previous chapter of interface intrduction and the figure

below to connect requied hardwares.(Note: Please disconnect the power of the

equipment while connecting signal.)

If it is required to control multiple MCTRL4K units, please connect them according

to the figure below.

XI'AN NOVASTAR TECH CO.,LTD.

MCTRL4K User‘s Manual

-4-

3 Dimensions

(mm)

4 Operating Motion Instruction

Knob:

While in main interface, press the knob to enter menu interface;

While in menu interface, rotate the knob to select menus and press the

knob to select current menu or enter submenus;

Select a menu with parameters and rotate the knob to adjust the

parameters. Please remember to press the knob again for confirmation after

adjustment.

BACK: A return button to exit from current menu or operation.

Lock /Unlock buttons: Press and hold the knob and ESC key simultaneously.

XI'AN NOVASTAR TECH CO.,LTD.

-5-

MCTRL4K User‘s Manual

5 Main Interface

Switch on the controller and the main interface of its screen is shown as below:

A: Input state of signal sources. Blue indicates it has signal while gray indicates no

signal;

B: Current input source and its resolution, frame rate. For example, the information

of two DVI sources will be displayed alternately here when dual-link DVI is selected

as input.

C: Width, height and frame rate of the LED display being configured;

D: Status, the meanings of each status icon are introduced as follows:

Supply voltage of mainboard core

Temperature inside the controller

Brightness of LED display

/DVI1 and DVI2 are not synchronous/synchronous

/ / Control interface, not connected/connected to USB port/

connected to Ethernet port

/Screen unlocked/locked

E: Connection status of Ethernet ports. Blue indicates that the connection is available

and the port works as master control while gray indicates the port is not connected

or the connection is unavailable. Mark on the upper left corner of the icon indicates

that the connection is available and the port is in redundancy state.

F: Connection status of optical fiber ports. Blue indicates that the connection is

available and the fiber port works as master control while gray indicates the port is

not connected or the connection is unavailable. Mark on the upper left corner of the

icon indicates that the connection is available and the port is in redundancy state.

XI'AN NOVASTAR TECH CO.,LTD.

MCTRL4K User‘s Manual

-6-

6 Menu Operation

MCTRL4K is powerful and easy-to-use. In general, users can start a LED display and

operate it normally through first four steps. Users also can set other options in the

menu selectively for better display effects.

Step 1 Input Mode

MCTRL 4K supports two input modes: mosaic and muli-card.

Main

Brightness

Input Settings

Screen Settings

Display Control

Advanced Settings

Communication Settings

Language

Input Settings

Input Mode

Input Resolution

Input Mode

DVI Mode Mosaic

Input Source

Mosaic Mode

In mosaic mode, Auto, DP, HDMI or DVI×2(Mosaic direction is optional.) can be

selected as video input source.

In multi-card mode, MCTRL4K is used as two independent controllers and the

loading capacity of each is up to 3840×2160@30Hz. Now both DVI 1 and DVI 2

inputs are available and can be displayed on LED display simultaneously. But only

one of them can be set at the same time, namely, the currently selected video

input source.

In multi-card mode, the corresponding outputs of DVI 1 are Ethernet port 1~8 or

OPT1 while the corresponding outputs of DVI 2 are Ethernet port 9~16 or OPT2.

Tip: When input source is set to "Auto", the controller will automatically detect input

source depending on the priority order of DP>HDMI>DVI.

Step 2 Input Resolution

Users are capable of setting the resolution of each input source as required.

Input Settings

Input Mode

Input Resolution

Preset

Custom

Input resolution is able to be set through the following two methods:

I: Preset

XI'AN NOVASTAR TECH CO.,LTD.

Tabla de contenidos

Otros manuales de Controladores de NovaStar

NovaStar

NovaStar NovaPro UHD Manual de usuario

NovaStar

NovaStar MCTRL660 PRO Manual de usuario

NovaStar

NovaStar MCTRL660 PRO Manual de usuario

NovaStar

NovaStar MX40 Pro Manual de usuario

NovaStar

NovaStar CX80 Pro Manual de usuario

NovaStar

NovaStar NovaPro HD Manual de usuario

NovaStar

NovaStar NovaPro UHD Manual de usuario

NovaStar

NovaStar NovaPro UHD Jr Manual de usuario

NovaStar

NovaStar NovaPro UHD Jr Manual de usuario

NovaStar

NovaStar MX40 Pro Manual de usuario

NovaStar

NovaStar C1 Manual de usuario

NovaStar

NovaStar NovaPro UHD Manual de usuario

NovaStar

NovaStar MX6000 Pro Manual de usuario

NovaStar

NovaStar MCTRL4K Manual de usuario

NovaStar

NovaStar VX6s Manual de usuario

NovaStar

NovaStar VX6s Manual de usuario

NovaStar

NovaStar VX400 Manual de usuario

NovaStar

NovaStar NovaPro UHD Manual de usuario

NovaStar

NovaStar MCTRL4K Manual de usuario

NovaStar

NovaStar VX200 Manual de usuario

NovaStar

NovaStar VX600 Manual de usuario

NovaStar

NovaStar VX4S-N Manual de usuario

NovaStar

NovaStar MX Series Manual de usuario

NovaStar

NovaStar MX20 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario