Novar ED&S KarizmaPlus Manual de usuario

Intruder alarm system

Operating instructions

Introduction

The purpose of this user guide is to describe how to operate Karizma plus system. Some of the features

described in this guide may not be applicable to your installation and should be ignored. The engineer from the

alarm company will have completed the System Information Sheet (SIS) in this guide which gives information

specific to your installation. You will need to refer to this as you read this guide in order to check if certain

features have been used. If in any doubt consult your alarm company.

Alarm company (Installer) name: __________________________________________

Telephone number: _____________________________________________________

Account number: _______________________________________________________

Installation date: _______________________________________________________

KarizmaPlusTM

Keypad and Entry

codes

Keypads

You operate your intruder alarm system by means of

a keypad. Each keypad has numeric keys (0 to 9),

ENTER and ERROR. Over each key is a label which

describes the secondary function of each key. The

key will perform their secondary function when the red

FUNCTION indicator is lit.

Entry Codes

Before you can do anything with Karizma+ you will

need to key in a code using one of the keypads.

There are several types of entry code, which permit

different levels of control over the system. Check the

System Information sheet to see which codes have

been enabled. The different types of codes are:

ÿNormal - this code allows the system to be set,

unset, and reset after an alarm.

ÿManager - this code has the same functions as a

user code, but in addition the manager code can

add or delete all other codes, test the system,

view the event log, set the time and date, omit

24Hr points, and set the chime function.

ÿCleaner - special code which unsets only part of

the system, providing restricted access only to

certain areas of the premises.

ÿDuress - a special code which although

appearing to work exactly like a standard user

code will also cause the signalling device to

signal a Personal Attack alarm to the central

station. Do not use this code unless you are

under threat to set or unset the system.

"Always press the Enter key

after keying in your code or when making

a selection.

Operating instructions

Thursday 06-Jan

17:00:36

FUNCTION

DAY

DEF

SET B

ABC

SET A

GHI

SET C

VWX

GOTO

STU 9

MNO

AREA

JKL

OMIT

PQR

QSET

SPACE

ERROR ENTER

Karizma

Plus

Display 2 - lines of

16 characters per line

Primary functions

Secondary functions

Secondary functions are actioned when the FUNCTION LED is lit

DAY mode LED

Function LED

ENTER

Setting the

system

Fully Setting the system

When the premises are to completely vacated you

should set the full system. First, check that the

premises are physically secure - are all windows shut,

and all external doors locked ?

Key in a normal user code at the keypad nearest the

final exit door and press the ENTER key.

The exit period will start and the inside sounder will

produce the exit sound - a pip-pip-pip sound. The

display identify the program that you are setting.

The bottom line on the display may have been editted

during installation to read a different message, for

example it may read FULL SYSTEM.

You must now vacate the premises by the exit route

described in the SIS. The length of time that you have

to vacate the premises depends on the exit mode that

has been programmed. Check your SIS to find out the

exit mode of programme A.

Part-Set the System

A part-set allows detection points in part of the

protected premises to be set (turned on), while those

in other areas are not set. In a domestic installation it

is usual for a part-set to be programmed for use at

night time. This would allow the detection points

around the perimeter of the house (doors, windows,

etc), and all downstairs detectors to be enabled, while

detectors in the bedrooms and on the stairs are

disabled.

Karizma+ has 2 different part-set programs called B

and C. Check your SIS to see if these programs have

been enabled. If they have not been enabled then you

will not be able to use them.

If a part-set has been enabled you can part-set your

system by doing the following: Enter your code at a

keypad and press the ENTER key. The system will

begin to perform a full-set (setting programme A).

Within 5 seconds of entering your code (while the red

FUNCTION indicator is still on) you must press either

the SET B or SET C key to select one of the part-set

programmes and press the ENTER key. The display

will acknowledge this by displaying name of the

program being set.

The bottom line on the display may have been editted

during installation to read a different message, for

example it may read NIGHT TIME. Leave the

protected area by the exit route appropriate for that

part-set.

Karizma Plus

Program A Set

PROGRAM A

Program A Set

PROGRAM A

Program B Set

PROGRAM B

1) Set system?

Performing a Quick-Set

It is possible to override the programmed exit time by

use of the Quick Set function. This always gives you

3 seconds to vacate the protected area. Quick Set is

selected during the first 5 seconds of the exit period

(while the red FUNCTION indicator is on) by pressing

the QSET key on the keypad. To use this function

with one of the part-set programmes you must first

select the part-set (SET B or SET C), and then press

QSET.

Omitting points during setting

It is possible to omit one or more detection points

when you set the system. The omitted points will not

be able to cause an alarm when the system has set.

This facility may be useful if one of your detection

points has become faulty and keeps producing false

alarms.

Because omitting a detection point degrades the

security provided by your alarm system, your engineer

may have programmed only a limited number of

points to be omittable. Check your SIS to see which

points, if any, can be omitted.

Points can be omitted by pressing the OMIT key

during the first 5 seconds of the exit period (while the

red FUNCTION indicator is on).

The exit sound will stop, and the keypad will display

the first point from a list of points that can be omitted.

Use the çand èkeys (over the 8 and 9 keys) to

step through the list of points until the point you want

to omit is displayed. Now press the ENTER key. The

ïsymbol will move onto the second line of the

display.

Press the èkey to change the NO to YES, and

press the ENTER key.

The point will be omitted and the exit period will start

again.

You can omit as many points as you want using this

procedure. To omit points from a part-set program you

must first select the part-set by pressing SET-B or

SET-C.

Operating instructions

01:FRONT DOOR

Omit Point: NO

01:KITCHEN PIR

Omit Point:YES

Program QSet

PROGRAM A

Unsetting the

system

Cancelling the Exit procedure

If you key in your code, and then immediately decide

not to set the system, you can cancel the exit

procedure by one of the following ways:

During the first 5 seconds of the exit period and with

the red FUNCTION indicator still on, just press the

ERROR key twice to cancel the exit procedure.

The inside sounder will stop, the keypad will display

the ‘Goodbye’ message for a few seconds and then

display the time and date. The green DAY indicator

will remain on.

After the first 5 seconds of exit period you must key in

your code to cancel the exit procedure.

The inside sounder will stop, the keypad will display

the ‘System Unset by’ message for a few seconds

and display the time and date. The green DAY

indicator will remain on.

Unsetting the System

Entering the premises by the designated entry route

will cause the entry period to start. The inside sounder

will emit a slow beep-beep-beep sound. You must

now key in your code and press the ENTER key at the

nearest available keypad to cancel the entry period.

The length of time that you have is called the entry

time; check your SIS to see how long this is. During

the last 10 seconds of the entry period the entry tone

will raise in pitch to inform you of the urgency to enter

your code.

If you enter your code within the entry period the

inside sounder will stop, the keypad will display the

‘System Unset’ message for few seconds and then

display the time and date.

The green DAY indicator will light. The system is now

unset.

Karizma Plus

System Unset by

MANAGER

System Unset by

MANAGER

Enter your code?

*** Goodbye ***

MANAGER

Silence Alarm and

Reset system

Silencing an Alarm

If an alarm occurs whilst you are in or near to the

premises the alarm can always be silenced by

entering your code. If the system was set it will be

unset at the same time. If the alarm occurs while you

are away from the premises the outside and inside

sounders will automatically stop after the bell time

programmed by the engineer, see your SIS for the

bell time.

When you enter your code after an alarm, the keypad

will display the cause of the alarm on the top line.

The second line shows additional information, such as

the point which caused the alarm. The system will

now need to be reset as described in the next section.

Resetting after an Alarm

After an alarm the system will need to be reset by

entering a suitable reset code. The display will

alternate between the alarm cause and a prompt to

enter a reset code.

If the this prompt is displayed you can reset the

system using your own code. Key in your code and

press the ENTER key.

After the system has been reset it may enter a fault

lockout described in the next section.

If this prompt is displayed you may need to call out

the engineer to reset the system.

Operating instructions

Enter Your

Code

Engineer Reset

Required

INTRUDER

BACK DOOR

Fault Lockout

After resetting the system the keypad display will

either display the ‘System Reset’ message, or it will

show a count of the faults which still exist. This is

called fault lockout.

These faults must be cleared before the system can

return to Day mode.

To see a list of the faults press the ENTER key. The

keypad will display each fault for 5 seconds. When all

of the faults have been displayed it will again display a

count of the faults. It will often be necessary to call out

the engineer in order to clear these faults.

If you can, clear the faults until the display shows no

faults, then press the ENTER key to return to Day

mode.

Remote Reset

If the system needs to be reset by an engineer code

you may need to call out the engineer. Before you do

this, check the SIS to see if either the Remote Reset

or Anti-code Reset options have been enabled. If

either have been enabled it may be possible to reset

the system by following one of the procedures

described here:

Remote Reset

Your engineer will have given you instructions on how

to request a remote reset. Usually you will have to

telephone the central station, give details of the alarm,

and quote a password. The central station can then

reset your system via the signalling device which is

fitted to your system.

When the remote reset is received by your system,

the keypad will display the ‘System Reset’ message

for a few seconds. It will then either revert to the time

and date display, or display the number of faults

which still exist - this is a fault lockout.

Reset by Anti-code

If Anti-code reset has been enabled the keypad will

display the 4-digit Quote code. Make a note of this

number (it is different each time you use this facility)

and telephone your central station. You may need to

give details of the alarm and quote a password. You

will also need to quote the 4 digit number. The central

station will give you a 6 digit number called an

anti-code. Key in the anti-code to reset the system.

The keypad will either display the time and date, or it

will display the number of faults which still exist - this

is a fault lockout.

Karizma Plus

Quote Code

1400

System Reset by

STU

Faults: 1

ENTER to View

Faults: 0

ENTER to Exit

System Unset by

STEVE

Cleaner Access

Karizma+ has a code which permits selected areas of

the protected premises to be unset for the purpose of

cleaning or maintenance. This cleaner code works in

conjunction with cleaner access points which have

been programmed by the engineer. Check your SIS to

see if any points have been programmed for cleaner

access.

"The cleaner code cannot be

used to reset the system in alarm.

Group Shunt

The Group shunt facility allows part of the protected

premises to be unset without unsetting the whole

system. This is often used to allow access to a garage

or loading-bay area independently from the main area

of the protected premises. Check your SIS to see if

this facility has been provided.

The detection points in the group will operate

normally; they will be set when the system is set, and

unset when the system is unset. However, they can

also be unset (dis-armed) at any time by operating the

group shunt keyswitch. Your installation engineer

will give you details on how to do this.

Re-arming the group is done with the keyswitch.

However, if a detection point in the group is in fault,

eg a door has been left open, the group cannot be

re-armed. An led located close to the keyswitch will

light, or a buzzer may sound, when it is not possible to

re-arm the group. You must dis-arm the group by the

keyswitch; this will turn off the led or buzzer. Enter the

protected area and clear the faults before trying to

re-arm the group again.

Operating instructions

Manager Facilities

The manager code is normally used to carry out

system management functions. It is used to allocate

and delete other user codes, test the system, view the

event memory, etc.

On entry of the manager code in Day mode the

keypad will display the first managers menu option

The manager has 10 similar menu options. Use the

çand èkeys to move through the menus. To

perform a function press the ENTER key.

The manager code can be used to unset the system

in the normal way. It can also be used to set the

system, but the procedure is slightly different to the

normal user code.

MENU 1 - Set System

Menu 1 allows the manager to set the system. Go to

this menu and press the ENTER key.

The system will start to set as if a normal user code

had been entered. The options available to the normal

user, such as part-set and omit, are available in the

normal way.

MENU 2 - View Event Log

Menu 2 allows the manager to view the event log,

which is a list of the last 200 events to occur. Go to

menu 2 and press the ENTER key.

The keypad will display the last event to be logged. In

the example here, 145 is the event number (events

are numbered 1 to 200), USER RESET is the

description of the event.

The bottom line is the time and date that the event

was logged. Use the çand èkeys to move through

the event log. Press the ERROR key to return to

menu 2.

Some events have additional information which can

be viewed by pressing the ENTER key when the

event is displayed.

MENU 3 - Print event log

With the ADE Opus-42 printer connected it is possible

to print out the entire event log.

With menu 3 on display press the ENTER key.

Karizma+ will start to print the event log, starting with

the newest event first. Press ERROR at any time to

stop the printer.

Karizma Plus

Printing...

ERROR to Stop

2) View

Event Log?

145) USER RESET

09:36:21 19-Nov

1) Set System?

MENU 4 - Change User Type

and Name

Menu 4 allows you to add, change or delete users

from the system.

With menu 4 on display press the ENTER key.

The keypad now displays the first code from a list of

16. The top line of the display identifies the user, and

the bottom line gives the user type. Use the çand

èkeys to go to the user to be changed and press

the ENTER key.

The ïsymbol moves onto the second line. Now use

the çand èkeys to select the user type (refer to

section 3 for a description of the different user types),

and press the ENTER key.

The keypad now displays the name associated with

the code. The flashing cursor will be at the right of the

name. To change the name press the ERROR key

several times until the existing name has been

deleted and the cursor is at the left of the display.

Names are entered one letter at a time by using the

numeric keys on the keypad. On each key are either 2

or 3 letters, for example on the ‘1’ key are the letters

ABC. To enter the letter C press ‘1’-a1isdisplayed,

press it again and the 1 changes to A, press it again

and the A changes to B, press it again and the B

changes to C. Now press the ENTER key to register

the C and move on to the next letter. Once you have

entered the name press the ENTER key again to

accept it. Momentarily press the ERROR key to exit

the menus.

MENU 5 - Change User Code

Each user hasa2to6digit code. Menu 5 allows this

code to be changed. Use the çand èkeys to

select the code to be changed and press the ENTER

key.

Now key in a code of between 2 and 6 digits, and

press the ENTER key. If the code is already in use by

another user it will be rejected. Momentarily press the

ERROR key to exit the menus.

MENU 6 - Chime Points

The manager can put any security point on chime.

When a chime point is activated keypad will display

the name of the point, and the inside sounder will emit

a single dee-daa sound and then stop. This is often

useful in shops to warn of a customer entering

through the shop door, or in a house to warn of a

potential intrusion through the back door.

Menu 6 allows you to put a point on chime. Select the

point using the çand èkeys and press the ENTER

key.

Use the çand èkeys again to put the point on

chime, or remove it from chime, and press the ENTER

key again. Momentarily press the ERROR key to exit

the menus.

Operating instructions

01:FRONT DOOR

Chime Pt: NO

01:User Code

01:User Name

? USER 2

01:MANAGER

MANAGER

01 : MANAGER

MANAGER

02:USER 2

NOT USED

Tabla de contenidos

Otros manuales de Sistema de seguridad de Novar ED&S

Novar ED&S

Novar ED&S LS400 Manual de usuario

Novar ED&S

Novar ED&S Response PL4 Manual de usuario

Novar ED&S

Novar ED&S Simple Set Reader Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario