NORSE SK135 Manual de usuario
SK135
Electric Pressure Washer
OPERATION MANUAL
Read this manual carefully before use and keep it for future reference. Failure to do so
may result in injury, property damage and may void the warranty.
Products covered by this manual may vary in appearance, assembly, inclusions,
specications, description or packaging.
V 3.1
SK135
© NØRSE
2© NØRSE
English
2 Contents
3 Quick Start Guide
5 Parts guide
7 Nozzle / Patio brush
8 Detergent
10 Drawing from a barrel
10 General cleaning
11 Post operation / storage
12 Maintenance
13 Safety Symbols
13 Safety and Warning Information
15 Troubleshooting
15 Technical Data
16 Disposal Regulations
17 CE Certication
Contents
SK135
© NØRSE 3
© NØRSE
English
Quick Start Guide
The following steps describe the quickest method to get your pressure washer up and
running. However, it is essential you fully read this manual to ensure you are familiar with
the general safety features, precautions and functions necessary to operate the product.
Failure to do so may result in injury and damage to your washer or personal items.
1
23
Slide the handle (01) on the reel frame and x
it with two screws (23). Tighten the screws (23)
using a suitable screwdriver.
Push the hose reel crank (02) into the opening of
the reel (10), ensure it clicks in place. Screw the
water hose connector (04) to the water inlet (05)
Push the latch (17e) on the spray gun (17) to open
the connecting port and insert the connector of the
high pressure hose (9). Release the latch (17e) to
lock the hose (09) in place. Check the connection
by pulling on the hose. It should not pull out.
Insert the extension lance (18) into the end of the
spray gun (17) by pushing together and turning
clockwise at the same time.
Insert the variable nozzle (19) into the end of the
extension lance by pressing the blue button on the
end of the extension lance, then press the xed
spray nozzle into the extension lance and turn
clockwise until it “clicks into place.
02
01
23
10
05
04
17e
09
18
17
17f
17
19
SK135
© NØRSE
4© NØRSE
English
Before starting up the appliance check that the water supply hose is connected properly;
use of the appliance without water will damage it; do not cover the ventilation grilles when
the appliance is in use.
Screw the quick hose connector (20) on to your
garden hose and slide onto the quick connector
lter (04), it will “click” into place.
1. Make sure the on/off switch (6) is on ‘’O’’ (off)
2. Insert the plug into a socket.
3. Turn the on/off switch (6) to “I” (on).
4. Deactivate the trigger lock by pressing the
deactivate button (17b).
5. Press the trigger (17d), a water jet sprays out of
the nozzle.
6. Release the trigger (17d) to stop the water
outlet.
7. After use, activate the trigger lock pressing the
activate button (17c) to lock the trigger in its
off-position.
8. Turn the on/off switch (6) to “O’’.
20
04
06
17d
17c
17b
SK135
© NØRSE 5
© NØRSE
English
Parts guide
01
09a
10
09
08
06
05
04 20
17
28
18
16
15
14
13
08
11
12
07b
17f
17e
17d
17a
18a
07a
07c
17c
17b
02
03
25
24
19
SK135
© NØRSE
6© NØRSE
English
1. Handle
2. Hose reel crank
3. Wheel
4. Quick connector lter
5. Water inlet
6. On/off switch
7. Detergent tank
a. Regulator
b. Cap
c. Container
8. Storage compartment (lances)
9. High pressure hose
a. O-ring
10. Hose reel
11. Air vents
12. Cleaning needle
13. Lubricant tube (certain models)
14. Storage compartment (variable nozzle)
15. Storage compartment (plug)
16. Power cord with plug
17. Spray gun
a. Grip
b. Trigger lock (deactivate button)
c. Trigger lock (activate button)
d. Trigger
e. Latch
f. Connection port
18. Lance extension
a. Lock button
19. Detergent nozzle
20. Quick hose connector
21. Triangle brush
a. Adaptor
22. Patio brush
a. Angle connector
b. Regulator
c. Rotating nozzle
23. Screw ST4.8*16mm (x2)
24. Filtered hose
25. Fiber extension hose
26. Rotary brush
27. 90 turbo nozzle
28. 20 xed nozzle
22c
21a21
22a
22b
22 23
27
26
SK135
© NØRSE 7
© NØRSE
English
WARNING! Never use the variable nozzle and patio brush without the lance extension –
danger of injury!
19 - The detergent nozzle creates the correct pressure for detergent to draw and mix, applying an even
mix.
27 - The 90 turbo nozzle angles a powerful rotating jet for hard to reach areas.
28 - The 20 fixed nozzle is used for general cleaning purposes with a focused and powerful spray.
Nozzle / Patio brush
The triangle brush is specially designed to clean
rims and the wheel of vehicles.
Screw the adaptor (21a) on the triangle brush (21).
Then align the tongues of the adaptor (21a) with
the grooves of the spray gun (17) and insert it.
Securely t the accessory by turning it clockwise
and let it lock into place.
Align the angle connector to the top of the patio
brush (22) and the rotating nozzle (22c) to the
bottom side. Screw the rotating nozzle (22c) on
the thread of the angle connector. Tighten it well.
Attach the angle connector (22a) to the lance
extension. (18)
17
21a
21
22b
22c
22
19 27 28
SK135
© NØRSE
8© NØRSE
English
Detergent
Use the detergent setting to apply detergent. Some cleaning tasks can be completed with water alone,
but for most tasks the removal of dirt becomes more effective if a detergent is used.
NOTE: Only use mild, environmentally friendly detergents. Never use aggressive chemicals, abrasive
detergents or similar to avoid damage to your health, the product and the environment.
Unscrew the cap (7b) to open the tank (7c) and ll
with suitable detergent
Screw the cap back onto the tank.
Adjust the detergent ow with the regulator (7a) on
the cap (7b)
WARNING! Avoid skin contact with detergents, in particular contact with eyes! If detergent
gets in your eyes ush your eyes with clean water and seek immediate medical attention!
07b
07c
07a
07b
The following cleaning procedure will ensure that you achieve the most benecial results in the shortest
amount of time.
• Surface preparation
Clear the working area and make sure that all windows and doors are closed tightly. Make sure that all
plants and trees adjacent to the cleaning area are protected by a drop cloth.
• Initial high pressure rinse
The next step is to spray the cleaning surface with water to clear off any dirt or grime that may have
collected on the surface. If you use detergent, this will allow your detergent to attack the dirt that has
worked its way into the cleaning surface. Before triggering the gun, adjust the variable nozzle to a wide
spray pattern and slowly adjust to the desired spray pattern. This will help you avoid applying too much
pressure to the surface that could cause damage.
• Detergent application
Only use detergents formulated for pressure washers. Test the detergent in an inconspicuous area before
use. Follow the manufacturer’s label directions for mixing the correct concentrations of detergent to
water.
SK135
© NØRSE 9
© NØRSE
English
1. Unscrew the top of detergent applicator and ll with detergent.
2. Put the top of detergent applicator back on.
3. Attach the detergent nozzle to the spray gun.
4. Apply the detergent so it thoroughly covers the cleaning surface. Apply from bottom to top to prevent
the detergent from sliding down and streaking.
5. Allow the detergent to remain on the surface for a few minutes. This is a good time to use a brush to
lightly scrub heavily soiled areas. Never allow detergent to dry on the cleaning surface.
6. Remove detergent applicator from gun and replace with the lance.
7. Rinse detergent from surface.
8. Rinse the detergent applicator with clean water following each use.
9. Final rinse. Make sure you thoroughly rinse the surface and that all detergent has been removed.
• Shut down
1. Make sure all detergent is ushed from the system.
2. Turn off the motor.
3. Turn off the water supply.
4. Trigger the gun to de-pressurise the system.
5. After each use, wipe all surfaces of the pressure washer with a clean, damp cloth.
17
19
SK135
© NØRSE
10 © NØRSE
English
Distance from Cleaning Surface
Another factor that determines the impact force of the water is the distance from the spray nozzle to the
cleaning surface
Angle to the Cleaning Surface
When spraying water against a surface, maximum impact is generated when the water strikes the
surface head on. However, this type of impact tends to cause dirt particles to embed in the surface,
thereby preventing the desired cleaning action.
The optimum angle for spraying water against a surface is 45 degrees.
Avoid Damaging Surfaces
Damage to surfaces occurs because the impact force of the water exceeds the durability of the surface.
Never use a narrow high impact stream or a turbo / rotary nozzle on a surface that is susceptible to
damage.
The surest way to avoid damaging surfaces:
1. Adjust the variable nozzle to a wide spray pattern.
2. Place the variable nozzle approximately 4-5 feet from and 45 degrees to the cleaning surface.
3. Vary the spray pattern, spray angle and the distance to the cleaning surface until optimum cleaning
efciency is achieved without damaging the surface.
General cleaning
Drawing from a barrel
First ensure the machine is switched off before connecting / disconnecting any hoses or attachments.
Instead of attaching the hose from pump to tap, use the supplied hose and lter set placing the lter end
in the water supply.
It is advised that the water supply is on the same level as the washer. If you struggle to get initial suction,
remove the outlet hose from the pump and try drawing again - this reduces the pressure on the pump
making it easier to draw. Once owing, turn engine off and reconnect outlet hose before re-starting.
04
24
Tabla de contenidos
Otros manuales de Hidrolavadora de NORSE
