Nokia 7088 Guía de inicio rápido
Nokia Customer Care
7088 (RM-219)
Mobile Terminal
Disassembly/Assembly
Issue 1 03/2007 Company Confidential ©2007 Nokia Corporation
7088 (RM-219)
Disassembly/Assembly
Contents Page
Safety Information.................................................................................................... 3
ESD Protection..................................................................................................3
Assembly Instructions .............................................................................................. 4
Disassembly Instructions.......................................................................................... 4
Page 2 ©2006 Nokia Corporation Company Confidential Issue 1 06/2006
6088 (RM-218)
NokiaCustomerCare Disassembly/Assembly
Safety Information
Adhere to the following guidelines when assembling and disassembling the
mobile terminals.
QUALIFIED SERVICE
Only qualified personnel may install or repair mobile terminal equipment.
ACCESSORIES AND BATTERIES
Use only approved accessories and batteries. Do not connect
incompatible products.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user’s guide for detailed
safety instructions. Do not connect incompatible products
ESD Protection
Always follow ESD protection guidelines when disassembling and assembling
the mobile terminal. To avoid potential ESD damage, the recommendation is
to treat all assemblies and components as if they are sensitive to ESD.
(1) All Surface Mounted components must be handled as electrostatic
sensitive components.
(2) Prevent static discharge failures to all semiconductors and modules
containing ESD sensitive components by using appropriate ESD protective
equipment.
(3) Do not touch the component with bare hands, and always wear a
grounded wrist strap or footwear.
(4) A mobile terminal that is ready for use can be handled normally without
ESD protection. The battery can be replaced in normal conditions of use.
(5) All ESD-sensitive parts must be packed in metallized protective bags
during shipping and handling outside any ESD Protected Area (EPA).
Be especially careful to avoid contaminating the mobile terminal with any dust
during assembly.
Issue 1 06/2006 ©2006 Nokia Corporation Company Confidential Page 3
7088 (RM-219)
Disassembly/Assembly
Assembly Instructions
To assemble the mobile terminal, follow the “Disassembly Instructions” in reverse
order.
Disassembly Instructions
Use the following steps to disassemble the mobile terminal.
Disassembly Instructions
1. Tools for disassembly and reassembly.
2. Protect the main display surface with a film.
3. Press and slip off Battery Cover.
4. Pull upward to remove Battery.
6IP
Film
Tweezers
6IP
4IP
SRT-6
Page 4 ©2006 Nokia Corporation Company Confidential Issue 1 06/2006
6088 (RM-218)
NokiaCustomerCare Disassembly/Assembly
5. Use a TORX 6IP screw driver to loosen and
remove the four Torx screws (M1.4x3). When
using torque driver, set torque to 10Ncm @
700 rpm. The tolerance is +/-2Ncm.
6. Place the SRT-6 into the gap between
C-cover and D-cover, moving along with
perimeter, and lever the snaps to separate
C-cover and D-cover.
Issue 1 06/2006 ©2006 Nokia Corporation Company Confidential Page 5
7088 (RM-219)
Disassembly/Assembly
7. Pull D-cover away from hook of C-cover. 8. Disconnect the FPC from connector on
PCB.
9. Remove PCB from D-cover. 10. Remove keymat.
11. Remove the screw sponge from B-cover.
12. Use a TORX 6IP screw driver to
loosen and remove the two Torx screws
(M1.4x3). When using torque driver, set
torque to 10Ncm @ 700 rpm. The
tolerance is +/-2Ncm.
6IP
Page 6 ©2006 Nokia Corporation Company Confidential Issue 1 06/2006
6088 (RM-218)
NokiaCustomerCare Disassembly/Assembly
13. Place the SRT-6 into the gap between
A-cover and B-cover, moving along with
perimeter, and lever the snaps to separate
A-cover and B-cover.
14. Pull A-cover away from hook of B-cover.
15. Use a TORX 6IP screw driver to loosen
and remove the four Torx screws (M1.4x3).
When using torque driver, set torque to 10Ncm
@ 700 rpm. The tolerance is +/-2Ncm.
16. Remove PCB from D-cover.
17. Disconnect FPC from PCB. 18. Gently remove camera module by hand.
6IP
Issue 1 06/2006 ©2006 Nokia Corporation Company Confidential Page 7
7088 (RM-219)
Disassembly/Assembly
19. Gently remove FPC of LCD from PCB. 20. Remove LCD from PCB carefully.
21.Use tweezers and pull upward to remove
headset jack.
22. Use tweezers and pull upward to remove DC
jack.
23. Remove speaker by tweezers.
24. Use a TORX 4IP screw driver to loosen and
remove the four Torx screws (M1.4x2). When
using torque driver, set torque to 10Ncm @ 700
rpm. The tolerance is +/-2Ncm.
Page 8 ©2006 Nokia Corporation Company Confidential Issue 1 06/2006
6088 (RM-218)
NokiaCustomerCare Disassembly/Assembly
25. Use a TORX 4IP screw driver to loosen and
remove the six Torx screws (M1.4x2). When
using torque driver, set torque to 10Ncm @
700 rpm. The tolerance is +/-2Ncm.
26. Pull out the sheet metal gently by hand
27. Remove side keys by tweezers.
Issue 1 06/2006 ©2006 Nokia Corporation Company Confidential Page 9
Otros manuales para 7088
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Portátil de Nokia
Nokia
Nokia RM-51 Manual de usuario
Nokia
Nokia RM-761 Manual de usuario
Nokia
Nokia RM-364 Manual de usuario
Nokia
Nokia RM-779 Manual de usuario
Nokia
Nokia 1265 Guía
Nokia
Nokia 2255 Guía
Nokia
Nokia 2700c-2 Manual de usuario
Nokia
Nokia 6235 Manual de usuario
Nokia
Nokia 6255 Instrucciones de instalación
Nokia
Nokia RH-66 Instrucciones de funcionamiento
Nokia
Nokia RM-429 Manual de usuario
Nokia
Nokia 6088 Guía de inicio rápido
Nokia
Nokia 6255 Guía
Nokia
Nokia RM-801 Manual de usuario
Nokia
Nokia RM-42 Manual de usuario
Nokia
Nokia RM-164 Manual de usuario
Nokia
Nokia RM-609 Manual de usuario
Nokia
Nokia RM-701 Manual de usuario
Nokia
Nokia RH-77 Guía de inicio rápido
Nokia
Nokia RM-237 Manual de usuario
